Best Bench Vise Under $100 (2026): 5 Shop Picks
Five bench vises under $100 compared on jaw width, clamping force, swivel base and warranty, from what each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallForward 1305 5 Inch9.7/10View on Amazon - 2
Best WarrantyZGJDYSM 6 Inch Dual Jaw9.6/10View on Amazon - 3
Best Pipe ViseVEVOR 5 Inch Multipurpose9.6/10View on Amazon - 4
Biggest JawsNakkaa 8 Inch9.5/10View on Amazon
Most fab jobs reach a point where two hands are not enough. You need to grind a bevel, drill a clean hole pattern, hold a fitting at an angle while you tack it, or cut a short length of pipe square. That is when a bench vise earns its bench space: it holds the work still so both hands are free and the angle grinder does not kick. This guide covers the best bench vise under 100 for a home or farm shop: five vises compared on jaw width, clamping force, swivel base, materials, warranty and what each listing puts in the box.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Forward 1305 5 Inch: 5,500 lbs clamping force, 60,000 PSI ductile iron, 120 degree swivel, 1 year warranty. Check price on Amazon
- Best Warranty ZGJDYSM 6 Inch Dual Jaw: 2 year replacement promise, two jaw sets, clamp on base, no drilling needed. Check price on Amazon
- Best Pipe Vise VEVOR 5 Inch Multipurpose: Pipe jaw for 0.59 to 2.36 in stock, 360 degree base, bolts in the box. Check price on Amazon
- Biggest Jaws Nakkaa 8 Inch: 8 in jaws, 360 degree base, ductile iron, replaceable microgroove steel jaws. Check price on Amazon
The machines

Forward 1305 5 Inch Bench Vise Workbench Vise
A 5 inch ductile iron bench vise with a stated 5,500 lbs clamping force, a 120 degree swivel base, a 1.9 by 1.9 in anvil and a 1 year limited parts replacement warranty.
Pros
- 5,500 lbs clamping force, the highest stated here
- 60,000 PSI ductile iron body
- Replaceable microgroove top jaws
- 1 year limited parts replacement warranty
Cons
- Swivel base rotates 120 degrees, not a full 360
- No pipe jaws are stated
- Anvil is small at 1.9 by 1.9 in
- Listed for home workshop use, not heavy fabrication

Bench Vise, 6" Jaw Width
A 6 inch clamp on bench vise with two interchangeable jaw sets, a 270 degree swivel base and a 2 year unconditional replacement promise, for woodworking, welding and DIY.
Pros
- 2 year unconditional replacement promise
- Two jaw sets: aluminum alloy V-groove and rubber jaws
- Clamp on base, no drilling the bench
- 270 degree swivel base
Cons
- No clamping force is stated
- 270 degree swivel, not a full 360
- 3.6 in max opening is modest for a 6 in vise
- Cast iron body, not ductile iron

VEVOR Bench Vise, 5" Jaw Width
A 5 inch ductile iron bench vise with a stated 4496 lbs clamping force, a 360 degree swivel base, built in pipe jaws and mounting bolts in the box.
Pros
- 4496 lbs clamping force (19.96 kN) from ductile iron
- 360 degree swivel base with a 4 bolt mounting pattern
- Built in pipe jaw for 0.59 to 2.36 in round stock
- Mounting hardware in the box: 4 M10 nuts and 4 M10*50 bolts
Cons
- No warranty term is stated
- No safety listing is stated
- Anvil area is smaller than the PONY's
- No replaceable jaws are stated

PONY 5-Inch Heavy-Duty Bench Vise with Swivel Base
A 5 inch gray iron bench vise with 3968 lbs clamping force, a 360 degree swivel base, pipe jaws and a 2-3/4 by 2-3/4 in anvil.
Pros
- 3968 lbs clamping force
- Largest anvil area here: 2-3/4 by 2-3/4 in
- Pipe jaws plus flat jaws for tube and pipe
- One pair of jaw pads in the box
Cons
- Gray iron body, not ductile iron
- 4 in jaw opening is the smallest of the 5 in vises
- No warranty term is stated
- No safety listing is stated

Nakkaa 8 Inch Heavy Duty Cast Iron Bench Vise 360°
An 8 inch ductile iron bench vise with a 360 degree swivel base, a chrome plated spindle and replaceable microgroove steel jaws, for garage and DIY metalwork.
Pros
- 8 in jaw width, the widest here
- 5.9 in maximum opening per the bullets
- Chrome plated spindle and nuts
- Replaceable microgroove steel jaws
Cons
- No clamping force is stated
- No warranty term is stated
- 12.59 kg is light for an 8 in vise
Other welders and gear to compare
MYTEC 2-In-1 Bench Vise Heavy Duty for WorkbenchCheck price on Amazon
AV Steel 4-1/2" Bench Vise with 240° Flexible Swivel LockingCheck price on Amazon
Forward 1750B 5 Inch Bench Vise Heavy Duty with Anvil andCheck price on Amazon
MYTEC Bench Vise or Table ViseCheck price on Amazon
MYTEC 2-In-1 Work Bench ViseCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Jaw width | Jaw opening | Clamping force | Swivel base | Warranty |
|---|---|---|---|---|---|---|
| Forward 1305 5 Inch | 9.7/10 | 5 in | 5 in | 5,500 lbs | 120 degrees | 1 year |
| ZGJDYSM 6 Inch Dual Jaw | 9.6/10 | 6 in | 3.6 in | Not stated | 270 degrees | 2 years |
| VEVOR 5 Inch Multipurpose | 9.6/10 | 5 in | 5 in | 4496 lbs | 360 degrees | Not stated |
| PONY 29050 5 Inch | 9.5/10 | 5 in | 4 in | 3968 lbs | 360 degrees | Not stated |
| Nakkaa 8 Inch | 9.5/10 | 8 in | 5.9 in | Not stated | 360 degrees | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (22 October 2026). Where a listing states a figure two ways, the table shows both.
Buying guide: best bench vise under 100
Jaw width and opening
The Nakkaa has the widest jaw here at 8 in, with the bullets giving a 5.9 in maximum opening while the specification table says 4.72 in. The ZGJDYSM has a 6 in jaw with a 3.6 in opening. The other three are 5 in vises: the Forward and the VEVOR open to 5 in, the PONY to 4 in. Buy jaw width for the stock you hold most, and check the opening against the thickest part you will clamp, because a wide jaw with a short opening still will not swallow a tall fitting.
Clamping force
The Forward states 5,500 lbs of clamping force, the highest figure in this guide. The VEVOR states 4,496 lbs (19.96 kN) and the PONY 3,968 lbs. The Nakkaa and the ZGJDYSM give no clamping force figure at all, so their holding power has to be judged on jaw width and build alone. A stated number beats a vague one when you plan to crank the handle down hard.
Swivel base and mounting
The VEVOR, PONY and Nakkaa state a 360 degree swivel base, so the work can turn to face you instead of you walking around the bench. The ZGJDYSM turns 270 degrees and the Forward 120 degrees, which covers most shop positions but not a full turn. Mounting differs too: the VEVOR ships 4 M10 nuts and 4 M10*50 bolts for its 4 bolt pattern, the PONY has 4 mounting tabs, the Nakkaa 3 mounting holes and the Forward includes 3 bolts with dual locking nuts. The ZGJDYSM clamps to the bench edge with a 2.3 in clamping range, the only pick here that needs no drilling.
Ductile iron, cast iron and gray iron
The Forward, VEVOR and Nakkaa state ductile iron bodies. The Forward rates its iron at 60,000 PSI and calls it 3 times stronger than gray iron, which is what the PONY states as its material. The ZGJDYSM states cast iron with steel jaws that have been heat treated. Marketing aside, ductile iron is the stronger stated material among these picks, and replaceable jaws, stated on the Forward and the Nakkaa, mean a damaged jaw does not junk the vise.
Warranty and what is in the box
The ZGJDYSM promises an unconditional replacement if the vise malfunctions under normal use within 2 years, the strongest written term here. The Forward gives a 1 year limited parts replacement. The VEVOR, PONY and Nakkaa state no warranty term. Boxes vary: the VEVOR includes 2 magnetic jaw pads, 4 M10 nuts and 4 M10*50 bolts, the PONY includes one pair of jaw pads, the Forward includes 3 mounting bolts and the ZGJDYSM ships a second jaw set.
Vise safety. Clamp the work so it cannot walk out of the jaws before you strike, grind or drill. Wear eye protection when hammering on the anvil or chipping slag near the vise, keep fingers clear of the jaws while you tighten the handle, and bolt the base down before any heavy pounding. See our Safety Disclaimer page for the full text.
Before You Strike an Arc
- Mount it like you mean it: 4 M10 bolts on the VEVOR, 4 tabs on the PONY, 3 holes on the Nakkaa, 3 included bolts on the Forward, or the clamp on base of the ZGJDYSM with its 2.3 in range.
- Check the swivel locks on arrival: the Forward uses dual locking nuts on a 120 degree base, the ZGJDYSM turns 270 degrees, and the rest turn a full 360 degrees.
- Inspect the jaws and anvil before the first job: look for chipped microgroove teeth on the Forward and Nakkaa, and confirm the jaw pads on the PONY and VEVOR sit flat.
- Keep the screw clean: brush scale and spatter off the slide after welding nearby so the handle keeps turning free, especially on the chrome plated spindle of the Nakkaa.
FAQ for welders
What size bench vise do I need for a home shop?
The picks here run from 5 to 8 inch jaw widths, with openings from 3.6 to 5.9 in depending on how you read the Nakkaa listing. A 5 inch vise holds most repair stock, from flat bar to small fittings, and keeps the bench footprint small. The 8 inch Nakkaa swallows bigger stock but weighs in at 12.59 kg and wants a stout bench.
Is ductile iron stronger than cast iron for a bench vise?
The Forward rates its ductile iron at 60,000 PSI and calls it 3 times stronger than gray iron vises. The VEVOR and Nakkaa also state ductile iron, the PONY states gray iron and the ZGJDYSM states cast iron with heat treated steel jaws. Treat the 3 times figure as the maker’s marketing, but ductile iron is the stronger stated material among these picks.
Do I need a 360 degree swivel base on a bench vise?
A swivel base lets you turn the work instead of walking around the bench, which matters in a tight garage. The VEVOR, PONY and Nakkaa state 360 degrees, the ZGJDYSM 270 degrees and the Forward 120 degrees. Lock the base solid before hammering, because a swivel that slips under load does no good.
How do I mount a bench vise without drilling the bench?
The ZGJDYSM clamps to the bench edge with a 2.3 in clamping range and states no drilling is needed. The others bolt down: the VEVOR ships 4 M10 nuts and 4 M10*50 bolts for a 4 bolt pattern, the PONY has 4 mounting tabs, the Nakkaa 3 mounting holes and the Forward includes 3 bolts. Whichever you pick, sit the base flat and tighten the hardware evenly.
Can I hammer on the anvil of a bench vise?
The anvil is the small flat for light peening and straightening, not the jaws or the slide. The PONY states the largest anvil here at 2-3/4 by 2-3/4 in, the VEVOR 2.17 by 2.36 in and the Forward 1.9 by 1.9 in. The Forward calls itself light duty, so keep hammer work proportionate to the vise you bought.
Related: best 6 bench vise for a wider lineup, best bench vise for farm shop, and best bench vise under 50. Also see our metal fab tools hub.
Scoring, line by line
Each vise is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. A spec the listing does not publish scores nothing.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Forward 1305 5 Inch | 9.7 | 29 | 22 | 21 | n/a | 3 |
| ZGJDYSM 6 Inch Dual Jaw | 9.6 | 27 | 19 | 20 | n/a | 4 |
| VEVOR 5 Inch Multipurpose | 9.6 | 28 | 21 | 21 | n/a | 0 |
| PONY 29050 5 Inch | 9.5 | 27 | 20 | 20 | n/a | 0 |
| Nakkaa 8 Inch | 9.5 | 26 | 20 | 19 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.





