Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Types of Toggle Clamps for Fabrication

Horizontal and vertical hold-downs, pull-action latches and auto-adjust clamps compared by holding capacity, handle position and mounting, so you can pick the shape that fits the jig.

Types of Toggle Clamps for Fabrication
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Amarite Steel Plate Lifting Clamp 0.8 TonAmarite Steel Plate Lifting Clamp 0.8 Ton9.7/10View on Amazon
  2. 2GleamRad 11-Inch Locking C-Clamp PliersGleamRad 11-Inch Locking C-Clamp Pliers9.6/10View on Amazon
  3. 3HORUSDY 4-Pack 12-Inch Bar Clamp SetHORUSDY 4-Pack 12-Inch Bar Clamp Set9.6/10View on Amazon

A toggle clamp holds work still with a flick of the handle, and the linkage locks past center so the bar stays put while you weld, drill or sand. The shape of the handle and the direction the bar moves decide which clamp fits a jig, and the wrong shape gets in the way of the torch or the drill. This guide explains the types of toggle clamps used in fabrication, what each shape does, and how to match the clamp to the job on the bench.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Types of toggle clamps at a glance

4 shapes cover most shop work: horizontal hold-down, vertical hold-down, pull-action latch and auto-adjust. The table below lines them up by holding capacity, handle position and mounting. For the wider family, see the types of metal clamps guide.

Horizontal hold-down Vertical hold-down Pull-action latch Auto-adjust
Holding capacity 360 lbs on the GH-201-B, 198 lbs on the E-TING 201B, 60 lbs on the Acrux7 201-L 500 lbs on the POWERTEC 12130, 397 lbs on the Auniwaig GH-101-D 7716 lbs on the KEILEOHO, 7480 lbs and 4000 lbs on the MOUYAT latches 25 to 550 lbs clamping force, 700 lbs max holding on the BESSEY STC-HH70
Handle position when clamped Horizontal Vertical Lever pulls a U-bolt tight Horizontal
Bar motion Arm opens 85 degrees, handle moves 80 degrees on the GH-201-B Bar moves 100 degrees, handle moves 60 degrees on the Auniwaig GH-101-D U-bolt draws the latch closed Spindle adjusts on its own to work thickness
Best for Jigs, fixtures, welding and drill press work Hold-down work where the handle stays clear Lids, toolboxes, cases, trailers and cabinets Mixed work thickness with no spindle adjustment
Mounting M4 or M5 screws; screws not included in the 12 piece packs Flanged base; 1/4 inch holes spaced 3/4 by 1-1/4 inches on the POWERTEC 12130 Screws fix the latch and hook to the lid or box Flanged base for 1/4 inch or M6 fasteners

Horizontal hold-down clamps

The horizontal handle clamp is the common jig clamp. The handle lies flat when the clamp locks, and the bar swings down over the work. The GH-201-B pattern shows up in 12 piece packs with a holding capacity of 360 lbs and a 163 kg figure in the same listing, an arm that opens 85 degrees and a handle that moves 80 degrees, a 6 mm mounting hole and a U-shaped clamping bar. Mount it with M4 or M5 screws; the packs state the screws are not included.

Smaller horizontal clamps suit light jigs. The Acrux7 201-L holds (on Amazon) 60 lbs, or 27 kg, in a 3.1 by 0.9 by 0.7 inch body, with a handle that opens 75 degrees and a bar that opens 90 degrees, and it comes in a 16 piece pack. The E-TING 201B (on Amazon) holds 198 lbs in a 3.7 by 2.56 by 1.5 inch body. The E-TING body is cold-rolled carbon steel with a zinc plated coating and red vinyl grips; the Acrux7 body is the same steel with a galvanized coating and a red vinyl-coated handle. Each carries an adjustable rubber pressure tip.

The auto-adjust horizontal clamp is a separate shape worth knowing. The BESSEY STC-HH70 (on Amazon) sets its own clamping force from 25 to 550 lbs, with a max holding capacity of 700 lbs, and it adjusts to varied work thickness without manual spindle adjustment. It carries a 1 year warranty against manufacturing defects and a 2 1/4 by 2 1/2 inch flanged base for 1/4 inch or M6 fasteners.

Vertical hold-down clamps

A vertical handle clamp locks with the handle standing upright, which keeps the handle clear of the work and the tool path. The POWERTEC 12130 (on Amazon) holds 500 lbs, measures 1-3/8 by 1-7/8 inches, and has mounting holes of 1/4 inch spaced 3/4 by 1-1/4 inches apart and a bolt length of 2-1/2 inches including the rubber foot. It comes in a 4 pack and fits the 71416 Toggle Clamp Mounting Plate and T track for 1/4 inch hex head bolts and 5/16 inch t-bolts.

The Auniwaig GH-101-D (on Amazon) is a vertical clamp with a long U-bar and a holding capacity of 397 lbs, or 180 kg. Total height is 145 mm, or 5.7 inches, when clamped, and the base measures 39.4 by 42 mm, or 1.55 by 1.65 inches. The thread is M8 by 65 mm, the handle moves 60 degrees and the bar moves 100 degrees. The body is high carbon steel with a zinc plated coating and a molded-on rubber tip.

Pull-action latch clamps

A pull-action latch clamp, also called a toggle latch, pulls a U-bolt tight to hold a lid, door or case shut instead of pressing down on a workpiece. The KEILEOHO latch holds 7716 lbs, or 3500 kg, with a lock hole in the lever, a U bolt and locking plates with a bottom thickness of 10 mm. The installation distance is 35 by 57 mm, and it comes in a 2 pack.

The MOUYAT latches come in the same shape at lower capacities: 7480 lbs on the 40380 and 4000 lbs on the 40370, each in a 2 pack with an adjustable threaded U bolt and an alloy steel body. These latches suit toolboxes, cases, wooden boxes, machinery, automobiles and jig assemblies.

How to pick the right type

Start with the direction of the load. A hold-down clamp presses work onto a bench or jig, while a latch pulls a lid or case closed. Pick the shape that matches the motion, then check the holding capacity against the work. Light circuit boards and paper need far less force than a welding fixture. A small horizontal clamp in the listings holds 60 lbs, while a heavy latch holds 7716 lbs.

Check the mounting before ordering. Horizontal 201-B packs mount with M4 or M5 screws that the packs do not include, the POWERTEC vertical clamp uses 1/4 inch holes spaced 3/4 by 1-1/4 inches, and the BESSEY auto-adjust base takes 1/4 inch or M6 fasteners. Check the swing too: the GH-201-B arm opens 85 degrees, the Acrux7 bar opens 90 degrees, and the Auniwaig bar moves 100 degrees, so a clamp that swings into a fence or a wall will not close.

Think about the spindle and the pad. A fixed spindle needs manual adjustment when the work thickness changes, while the BESSEY auto-adjust clamp changes its own force from 25 to 550 lbs as the thickness varies. The BESSEY includes a removable non-marring plastic cap on steel pressure pads, and the POWERTEC and Acrux7 clamps use rubber tips.

Mounting and setup checks

Mount the clamp on a flat, solid surface and tighten the fasteners fully before loading it. A clamp that rocks on its base will not hold its rated capacity. Keep fingers clear of the pivot and the bar while closing the clamp, wear eye protection when drilling, grinding or cutting near clamped work, and check the hold by hand before the cutter touches metal.

FAQ for welders

What is the difference between a horizontal and a vertical toggle clamp?

The handle position when clamped is the difference. A horizontal clamp locks with the handle lying flat, as on the GH-201-B, while a vertical clamp locks with the handle standing upright, as on the POWERTEC 12130 and the Auniwaig GH-101-D. Pick the shape that keeps the handle clear of the torch, the drill or the cutter.

How much holding capacity do I need for a welding jig?

Match the capacity to the job, not to the clamp. A small horizontal clamp in the listings holds 60 lbs, the GH-201-B holds 360 lbs, the POWERTEC 12130 holds 500 lbs, and heavy pull latches hold 4000 lbs and 7716 lbs. A light jig for circuit boards or paper needs the small end of that range.

Do toggle clamps come with mounting screws?

Not always. The 12 piece GH-201-B packs state the screws are not included and mount with M4 or M5 screws, while the BESSEY STC-HH70 base takes 1/4 inch or M6 fasteners. Check the listing for the fastener size and buy screws to match before the clamp arrives.

What does auto-adjust mean on a toggle clamp?

It means the clamp changes its own clamping force to suit the work thickness. The BESSEY STC-HH70 applies a clamping force from 25 to 550 lbs and holds up to 700 lbs, with no manual spindle adjustment between pieces of varied thickness. A standard clamp needs the spindle set by hand for each thickness.

Related: types of metal clamps, magnetic clamp vs toggle clamp, toggle clamp vs bar clamp, best welding clamps under 35, best quick clamps for metal, best CNC mill fixture clamps, and the types of toggle clamps hub.

More buying guides

Metal Fab Tools ·

Toggle Clamp Parts and Components

The handle, linkage, spindle, pad, base and spring of a toggle clamp, and how to match their holding capacities to jigs and fixtures.

Metal Fab Tools ·

Toggle Clamp Uses in Metal Fabrication

A toggle clamp holds work still with a pull of the handle, and the right type depends on the job: hold down clamps for…