Toggle Clamp Parts and Components
The handle, linkage, spindle, pad, base and spring of a toggle clamp, and how to match their holding capacities to jigs and fixtures.

On this page
A jig holds the work still while the bead goes down, and the clamp on that jig is what keeps the work from moving. Toggle clamp parts are the handle, the linkage, the spindle, the pressure pad, the base and the spring that work together to lock the clamp over center and hold the work against the jig. This guide names each part, shows what it does, and shows how to match the parts to the job.
As an Amazon Associate I earn from qualifying purchases. This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Toggle clamp parts at a glance
A toggle clamp has a small set of parts, and each part has one job. The handle is the lever the hand pulls. The linkage joins the handle to the clamping bar and carries the motion over center, past the point where the clamp locks and stays shut until the handle is pulled back. The spindle is the threaded rod through the bar, and the pressure pad on its end is the part that meets the work. The base is the foot that bolts to the jig, and the spring holds the linkage in place when the clamp is open. Learn the parts in the types of toggle clamps guide, then come back here for the detail on each part.
Side by side
| Horizontal hold down | Push pull | Latch | |
|---|---|---|---|
| What moves | A bar swings down onto the work | A spindle pushes straight ahead | A U-bolt pulls tight to hold a lid shut |
| Holding capacity | 198 to 500 lbs | 110 lbs | 2000 lbs |
| Spindle or catch | Adjustable rubber pressure tip | Rubber indenter | Adjustable U-bolt |
| Typical use | Jigs and fixtures | Cabinets and fixture assembly | Lids, doors and tool boxes |
The table shows the actions the listings cover. A horizontal hold down clamp swings a bar down onto the work, a push pull clamp drives a spindle straight ahead, and a latch pulls a U-bolt tight to hold a lid shut. The holding capacity the maker lists runs from 110 lbs on a push pull clamp to 2000 lbs on a latch, with horizontal hold down clamps rated at 198 lbs and 360 lbs and a heavy duty horizontal model rated at 500 lbs. Pick the action first, then the capacity.
The handle and linkage
The handle is the lever, and the linkage is the set of arms and pivots that turns a pull on the handle into clamping force. On the GH-201-B the maker lists an arm that opens 85 degrees while the handle moves 80 degrees, so a short pull swings the bar clear of the work. The linkage also resists side thrust, so the clamp holds its line when the work pushes sideways. BESSEY lists a cushion grip handle 1 inch by 2 1/8 inches on its auto adjust model, and a clamping force adjustment screw that sets the applied force from 25 to 550 lbs, with a max holding capacity of 700 lbs. Red vinyl grips are common: the maker lists an oil and stain resistant red vinyl hand grip on the GH-201-B, and an oil resistant red vinyl handle on the 225D model.
The spindle and pressure pad
The spindle is a threaded rod that runs through the clamping bar, and turning it sets how far the pad reaches down to the work. The maker lists adjustable rubber pressure tips on the 201-B, an adjustable pressure tip on the 225D model, and a black rubber indenter on the push pull clamps in the 8 piece set. BESSEY lists steel pressure pads with a removable non marring plastic cap, so the pad meets the work without marking it. A latch uses an adjustable U-bolt in place of a spindle, which the maker lists on the latch model with a 2000 lbs capacity. Set the spindle so the pad meets the work with the handle locked over center, and check the hold before welding.
The base and mounting
The base is the foot of the clamp, and it is what bolts the clamp to a jig, a fixture or a bench. The maker lists a flanged base 2 1/4 inches by 2 1/2 inches on the BESSEY model, made for use with 1/4 inch or M6 fasteners. The GH-201-B lists a hole size of 6 mm and installs with M4 or M5 screws, and the maker states that the package does not include screws. A latch base can be fixed with screws or weld, per the maker. Drill the mounting holes to match the base, set the clamp square to the work, and tighten the fasteners before the first weld.
Match the holding capacity to the job
Holding capacity is the force the clamp holds with, and the maker lists it in lbs on each model. Light fixture work suits a push pull clamp rated at 110 lbs, while a 201-B horizontal clamp rated at 198 lbs and a GH-201-B rated at 360 lbs cover jigs and fixtures. The 225D horizontal model rated at 500 lbs suits heavier holding, and the latch rated at 2000 lbs suits lids, doors and tool boxes that need a strong pull shut. BESSEY lists an applied force from 25 to 550 lbs with a max holding capacity of 700 lbs, which covers a range of work piece sizes on one clamp. Match the capacity to the hold the job needs, and leave room for the work to push back. See the best large toggle clamp guide and the best horizontal hold down toggle clamp guide for rated models.
FAQ for welders
What is the spindle on a toggle clamp?
The spindle is the threaded rod through the clamping bar, and the pad on its end is the part that meets the work. Turning the spindle sets the pad height, so the clamp holds work of different thicknesses. The maker lists adjustable rubber pressure tips on the 201-B and an adjustable pressure tip on the 225D model.
How do I pick a holding capacity?
Read the holding capacity the maker lists in lbs, then match it to the hold the job needs. A push pull clamp rated at 110 lbs suits light fixture work, a GH-201-B rated at 360 lbs covers jigs and fixtures, and a latch rated at 2000 lbs suits lids and doors. When the work pushes back hard, pick the higher capacity.
Can I mount a toggle clamp on a welding table?
Yes, when the base and the table match. Bolt the base through its holes with the fasteners the maker lists, such as M4 or M5 screws on the GH-201-B or 1/4 inch or M6 fasteners on the BESSEY model. A latch base can also be fixed with screws or weld. Check the hold before the first weld, and see the magnetic clamp vs toggle clamp comparison for another way to hold work on a table.
What is the difference between a horizontal and a push pull toggle clamp?
A horizontal clamp swings a bar down onto the work from above, while a push pull clamp drives its spindle straight ahead. The GH-201-B horizontal clamp is rated at 360 lbs, and the push pull clamp in the 8 piece set is rated at 110 lbs. Use the horizontal clamp when the work sits flat on a jig, and the push pull clamp when the work needs a push from the side.
Do toggle clamps come with mounting screws?
Not always. The maker states that the GH-201-B package does not include screws, and the clamp installs with M4 or M5 screws. Check what is in the box before ordering, and buy the fasteners the maker lists for the base.
Related: types of toggle clamps, toggle clamp vs bar clamp, best large toggle clamp, and the metal fab tools hub.




