Types of Sanding Discs and Their Uses
Flap discs and resin fiber discs cover most angle grinder sanding, and the grit on the face decides whether the disc removes stock fast or leaves a smooth finish.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
BHA 4.5 Zirconia Resin Fiber Disc for Angle9.6/10View on Amazon - 2
14 Pack Zirconia Flap Discs 4 1/2 for Angle9.6/10View on Amazon - 3
Sali 10 Pack Flap Disc 60 Grit 4.5" x 7/8-Inch9.6/10View on Amazon
A weld bead stands proud of the plate, a cut edge carries burrs, and paint peels off in flakes. The disc on the angle grinder decides how fast that metal comes clean and how smooth it ends up. Types of sanding discs split mainly by build, flap discs and resin fiber discs, and by the grit on the face. This guide explains each type, the grit to start with, and the discs that show the range.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

BHA 4.5 Zirconia Resin Fiber Disc for Angle
A 24 grit zirconia resin fiber disc for stock removal and weld blending, in a 25 pack, rated to 13,200 RPM.
Pros
- Self-sharpening zirconia grain stays sharp as the disc wears
- 7/8 inch center hole fits 4.5 inch right-angle grinders
- Listed in 24, 36, 60, 80, and 120 grit for each stage of the work
- Contaminant free for stainless steel
Cons
- Needs a backing pad and disc retainer nut, sold separately
- 25 disc pack is more than a one-off job needs
- Rated to 13,200 RPM, so check the grinder speed before fitting
- No warranty term is stated

14 Pack Zirconia Flap Discs 4 1/2 for Angle
A 40 grit zirconia flap disc for wood and metal grinding, in a 14 pack, rated to 13,300 RPM.
Pros
- 40 grit zirconia abrasive for fast material removal
- 4-1/2 inch face with a 7/8 inch arbor fits most angle grinders
- 14 disc pack keeps spares on hand for repeat jobs
- Zirconium oxide abrasive for durability and strength
Cons
- 40 grit only in this pack, so finer finishing needs another disc
- 40 grit leaves a rough finish, so paint prep needs a finer disc after it
- No warranty term is stated
- Rated to 13,300 RPM, so check the grinder speed before fitting

Sali 10 Pack Flap Disc 60 Grit 4.5" x 7/8-Inch
A 60 grit zirconia alumina flap disc for edge grinding and weld blending, in a 10 pack, rated to 13,300 RPM.
Pros
- 60 grit coarse zirconia alumina for aggressive grinding on hard materials
- Type 29 bevel shape for contours, edge and weld blending
- Fiberglass backing plate absorbs vibration without smearing the work piece
- Covers rust removal, paint removal, blending, cleaning and finishing
Cons
- 60 grit only in this pack, so heavy removal needs a coarser disc
- 10 disc pack runs out fast on heavy grinding days
- Rated to 13,300 RPM, so check the grinder speed before fitting
- Fits 4.5 inch grinders, so it does not suit larger grinders
Types of sanding discs for an angle grinder
A sanding disc for an angle grinder is an abrasive disc that spins on the grinder spindle and cuts by rubbing grit across metal. This guide covers two builds: the flap disc and the resin fiber disc. Both come in the same common size for small grinders, a 4-1/2 inch face on a 7/8 inch arbor, and both wear down as they cut, so the grit choice matters more than the name on the label.
Flap discs
A flap disc is a ring of overlapping abrasive flaps glued to a backing plate. As the flaps wear, fresh grit shows, so the disc keeps cutting without loading up as fast as a flat sheet. The two flap discs in this guide are Type 29, a bevel shape angled for contours, edges and weld blending. Pukamam lists its 40 grit flap disc for wood and metal grinding, sanding and finishing, and Sali lists its 60 grit flap disc for rust removal, paint removal, weld blending and cleaning on ferrous metals, stainless steel, non-ferrous metals, wood and plastics. Flap discs suit blending best: knocking a weld bead flush, easing a sharp edge, and cleaning a surface before paint. For heavy stock removal, the fiber disc below is the stronger pick.
Resin fiber discs
A resin fiber disc is a flat disc of abrasive on a stiff vulcanized fiber backing. It has no flaps, so the full face cuts at once, which suits flat stock removal and weld blending. BHA lists its zirconia resin fiber disc for stock removal and weld blending, with self-sharpening zirconia grain that stays sharp as the disc wears and resin bonding that helps prevent clogging. The disc is contaminant free for stainless steel. A fiber disc needs a backing pad and a disc retainer nut, and BHA states both are sold separately. Fit the pad, seat the disc flat, and tighten the nut before the grinder starts.
Grit: what the number means
Grit is the size of the abrasive grain on the face. A low grit number means coarse grain, fast cutting, and a rough finish. A high grit number means fine grain, slow cutting, and a smooth finish. BHA lists its fiber disc in 24, 36, 60, 80, and 120 grit, which spans the full range from heavy weld removal to finer finishing. Start coarse only when there is real stock to remove: a tall weld bead, heavy rust, or a rough cut edge. Step up through the grits instead of jumping from coarse to fine, since each pass erases the scratches the last one left.
Side by side
| BHA 4.5 Zirconia Fiber Disc | Pukamam 14 Pack Flap Disc | SALI 10 Pack Flap Disc | |
|---|---|---|---|
| Disc type | Resin fiber disc | Type 29 flap disc | Type 29 bevel flap disc |
| Grit | 24 | 40 | 60 |
| Size | 4.5 in | 4-1/2 in | 4-1/2 in |
| Arbor | 7/8 in | 7/8 in | 7/8 in |
| Top speed | 13,200 RPM | 13,300 RPM | 13,300 RPM |
| Pack | 25 discs | 14 discs | 10 discs |
| Abrasive | Zirconia | Zirconium oxide | Zirconia alumina |
| Gear Score | 60 | 59 | 56 |
Each disc here has a 4-1/2 inch face and a 7/8 inch arbor, so the choice comes down to build and grit. The fiber disc cuts hardest at 24 grit, the 40 grit flap disc sits in the middle for cleanup, and the 60 grit flap disc finishes the blend.
Match the disc to the job
- Heavy weld removal and deburring. A 24 grit fiber disc, with its full face cutting at once.
- Weld blending and edge work. A Type 29 flap disc, 40 grit to knock the bead down, then 60 grit to blend it flush.
- Rust and paint removal. A 60 grit flap disc, which the Sali maker lists for rust, paint, ferrous metals and stainless steel.
- Stainless steel. A contaminant free fiber disc, so the ground surface stays rust free.
- Wood and plastic. A flap disc, which both flap disc makers list for wood, and Sali also lists for plastics.
Check the job against the disc before the grinder starts: the wrong grit wastes time, and the wrong build leaves marks the next step has to erase.
Speed and fit checks
Every disc here lists a top speed: the BHA fiber disc (on Amazon) is rated to 13,200 RPM, and both flap discs are rated to 13,300 RPM. Check the speed on the grinder body and fit only a disc rated at or above it. Each disc here uses a 7/8 inch arbor, so they fit grinders with that spindle size. Keep the guard in place, wear eye protection, and clamp the work before the disc touches metal. Goggles and other safety precautions are recommended for use, as Pukamam states.
The gear: discs that show the range
The discs below cover the builds this guide calls for: a fiber disc for the heavy removal step, a flap disc for the blending step, and a finer flap disc for the finishing step. Each card states what its maker lists, and the scores rank them on the stated specs.
FAQ for welders
What grit sanding disc starts a weld cleanup?
Start with 24 grit for a tall bead or heavy removal, then step to 40 grit and 60 grit to blend. The BHA fiber disc lists 24 grit for heavy weld removal, and the flap discs here run 40 grit and 60 grit for blending and finishing. Each step erases the scratches the last one left, so do not jump straight from coarse to fine.
Can a flap disc clean wood?
Yes, the makers say so. Pukamam lists its 40 grit flap disc for wood and metal grinding, and Sali lists its 60 grit flap disc for wood and plastics as well as metals. Keep the grinder moving so the disc does not burn one spot.
Do resin fiber discs need a backing pad?
Yes. BHA states its fiber disc requires a compatible backing pad and disc retainer nut, sold separately. Fit the pad, seat the disc flat, and tighten the nut before the grinder starts.
What arbor size fits these discs?
Each disc in this guide uses a 7/8 inch arbor. Check the grinder spindle size and the top speed on the grinder body before fitting a disc: the fiber disc is rated to 13,200 RPM and the flap discs to 13,300 RPM.
Related: flap disc uses, best 4 1/2 sanding disc for angle grinder, angle grinder types, and the metal fab tools hub.




