Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Sandblasting Nozzle Size Chart

4 nozzle sizes, from 6mm to 8mm, compared by bore, liner material and the air figures their listings state, so you can match the nozzle to the blaster.

Sandblasting Nozzle Size Chart
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Sandblaster Nozzle Combo Pack for AccessoriesSandblaster Nozzle Combo Pack for Accessories9.7/10View on Amazon
  2. 2Large Ceramic Sandblaster Assembly: C1 (5/16" ID)Large Ceramic Sandblaster Assembly: C1 (5/16" ID)9.6/10View on Amazon
  3. 3HOLDWIN Sandblaster Gun Nozzles 10Pcs Tip SandHOLDWIN Sandblaster Gun Nozzles 10Pcs Tip Sand9.6/10View on Amazon
  4. 4Jewboer Sand Blaster Gun Kit,SandblasterJewboer Sand Blaster Gun Kit,Sandblaster9.5/10View on Amazon

A rusty bracket goes into the cabinet, and the nozzle, the media and the air behind it set how fast the rust comes off and how clean the metal looks after. A sandblasting nozzle size chart answers one question: which bore fits the job and the air supply behind it. The chart below lists the nozzles in this guide by bore, material and the air figures their listings state, so you can match the nozzle to the blaster before you buy.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Sandblaster Nozzle Combo Pack for Accessories

Sandblaster Nozzle Combo Pack for Accessories

HEBRAR9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A steel nozzle combo pack with 5 nozzles, 2 air jets and gaskets for most siphon blasters, with a 1/4 in bore, 10-15 cfm and 60-100 psi stated.

Pros

  • 5 steel nozzles, 2 air jets, 2 air jet gaskets and 1 nozzle gasket in one pack
  • 1/4 in bore with 10-15 cfm and 60-100 psi stated
  • Case hardened steel with strong wear resistance, per the listing
  • Air jet size matches the nozzle size, per the listing

Cons

  • Each nozzle lasts about 1-2 hours, per the listing
  • No warranty term is stated in the listing
  • No certification is stated in the listing
  • No ceramic or boron carbide option in the pack
Large Ceramic Sandblaster Assembly: C1 (5/16" ID)

Large Ceramic Sandblaster Assembly: C1 (5/16" ID)

SandblasterINFO9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A large ceramic nozzle assembly with a 5/16 in bore, a 3/4 in stainless steel ball valve and a 3-3/4 in Kennametal tip for pressure pot systems.

Pros

  • 5/16 in bore for larger pressure pot systems
  • Alumina oxide ceramic tip, 3-3/4 in long, for longer wear
  • 3/4 in stainless steel N.P.T. ball valve and holder included
  • Kennametal tip, USA assembled, per the listing

Cons

  • No warranty term is stated in the listing
  • No certification is stated in the listing
  • No air figure is stated in the listing
  • No smaller bore option in the listing
HOLDWIN Sandblaster Gun Nozzles 10Pcs Tip Sand

HOLDWIN Sandblaster Gun Nozzles 10Pcs Tip Sand

HOLDWIN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-piece set of 6mm ceramic nozzles for deep engraving, rust removal and paint stripping on glass, marble and metal parts.

Pros

  • 10 ceramic nozzles in one set
  • 6mm bore for medium to deep blasting, per the listing
  • Stated for garnet, corundum, walnut shells, soda and beads
  • 0.8 by 0.8 by 1.4 inches, per the spec table

Cons

  • No warranty term is stated in the listing
  • No certification is stated in the listing
  • No air figure is stated in the listing
  • No air jet or gasket is included
Jewboer Sand Blaster Gun Kit,Sandblaster

Jewboer Sand Blaster Gun Kit,Sandblaster

Jewboer9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A sand blaster gun kit with an 8mm boron carbide nozzle for box manual and automatic sandblasting machines.

Pros

  • 8mm boron carbide nozzle, per the listing
  • Gun kit for box manual and automatic sandblasting machines
  • Stated for sand glass, surface polishing and machinery parts
  • Taper and length set pattern and velocity, per the listing

Cons

  • No warranty term is stated in the listing
  • No certification is stated in the listing
  • No air figure is stated in the listing
  • No dimensions, pack count or pressure is stated

Sandblasting Nozzle Size Chart: The Sizes in This Guide

The chart lists each nozzle by its bore, the liner material, and the air figures its listing states. Bore sizes run from 6mm to 8mm in this guide, with 1/4 in and 5/16 in in between. Where a listing states no air figure, the chart says so rather than borrowing a figure from another nozzle.

Gear Score Bore size Material Air and pressure stated
HEBRAR Nozzle Combo 9.7/10 1/4 in I.D. Case hardened steel 10-15 cfm, 60-100 psi
SandblasterINFO C1 9.6/10 5/16 in I.D. Alumina oxide ceramic Not stated
HOLDWIN 6mm Nozzles 9.6/10 6mm Ceramic Not stated
Jewboer 8mm Gun Kit 9.5/10 8mm Boron carbide Not stated

Read the chart with the listing behind each row. The HEBRAR figures for air and pressure belong to its 1/4 in nozzle only, and the other listings state no air figure at all. A bore size on its own does not set the air supply: check the manual for the blaster and the compressor behind it.

How to Read the Chart

Start with the bore. The bore is the hole the air and media pass through, and the Jewboer listing says the taper and length of the nozzle inlet and outlet set the pattern and velocity of the media leaving the nozzle. Match the bore to the work: the HOLDWIN 6mm ceramic (on Amazon) tips suit deep engraving, surface rust removal and paint stripping on glass, marble and metal parts, per the listing.

Then match the air jet. The HEBRAR listing says the size of the air jet must match the size of the nozzle, and its combo pack includes 2 air jets, 2 air jet gaskets and 1 nozzle gasket for that reason. The same listing says each steel nozzle lasts about 1-2 hours before the orifice wears larger, and that after 2-3 nozzles, the air jet and gasket go too. Change the nozzle when the bore grows, not when the finish goes bad.

Ceramic vs Steel vs Boron Carbide

Ceramic is the common liner here. The HOLDWIN tips are ceramic, made for garnet, corundum and walnut shells, and the listing calls them durable and resistant to corrosion. The SandblasterINFO C1 (on Amazon) uses an alumina oxide ceramic tip, 3-3/4 in long, and the listing says the longer tip outlasts small nozzles several times. That is the maker’s claim, and it rests on the extra material the long tip carries.

Steel is the workhorse in the HEBRAR combo (on Amazon): case hardened steel nozzles the maker says work better than ceramic ones, with strong wear resistance and long life. Boron carbide is the other liner here: the Jewboer gun kit (on Amazon) pairs a boron carbide nozzle with a blaster gun for box machines, and the listing says the liner material sets how well the nozzle resists wear. Match the liner to the media: the HOLDWIN listing names garnet, corundum, walnut shells, soda and beads as media its ceramic tips handle. See the blasting media chart for media types and grit sizes.

The Nozzles in This Guide

Each nozzle below fits a different setup: the HEBRAR combo for a siphon blaster that needs a matched air jet, the SandblasterINFO C1 for a pressure pot, the HOLDWIN tips for engraving and rust removal, and the Jewboer kit for a blast cabinet gun.

Before You Blast

Blasting throws media and dust, so wear eye and face protection and a respirator rated for the dust it makes, and blast in a cabinet or with ventilation that keeps the dust out of the shop air. Never point the nozzle at skin, and keep the air supply at the pressure the manual calls for. Check the manual for the media, the nozzle and the blaster before the first job.

FAQ for welders

What size sandblasting nozzle do I need?

Match the bore to the job and the air supply behind it. The HEBRAR 1/4 in nozzle states 10-15 cfm and 60-100 psi, and its listing says the air jet must match the nozzle size. The other listings in this guide state no air figure, so check the manual for the blaster and the compressor before you buy.

How long does a sandblasting nozzle last?

The HEBRAR listing says each steel nozzle lasts about 1-2 hours before the orifice wears larger to the next size, and that after 2-3 nozzles, the air jet and gasket go too. Change the nozzle when the bore grows. The other listings in this guide state no wear life, so their nozzles give no figure to plan against.

What is the difference between ceramic and steel nozzles?

Ceramic is the common liner here: the HOLDWIN tips are ceramic for garnet, corundum and walnut shells, and the SandblasterINFO C1 uses an alumina oxide ceramic tip. Steel is the HEBRAR combo: case hardened steel the maker says works better than ceramic, with strong wear resistance. Boron carbide is the liner on the Jewboer kit, and its listing says the liner material sets how well the nozzle resists wear.

Can I use a 5/16 in nozzle on a small pot blaster?

The SandblasterINFO C1 is made for larger pressure pot systems, and its listing says it can convert smaller garage pot systems such as Clarke and Harbor Freight. Check the manual for the air supply and the pot before you fit it, since the listing states no air figure.

Does the air jet size matter?

Yes, per the HEBRAR listing: the size of the air jet must match the size of the nozzle. Its combo pack includes 2 air jets, 2 air jet gaskets and 1 nozzle gasket, and the listing says to replace the air jet and gasket after 2-3 nozzles, so change them together.

Related: best sandblasting gloves, sandblasting vs wire wheel for rust removal, best large sandblasting cabinet and the metal fab tools hub.

More buying guides

Metal Fab Tools ·

Sandblasting Nozzle Tips and How to Choose

Sandblasting nozzle tips shape the abrasive stream, and the orifice size, material and air supply decide how fast the surface cleans and when the…

Metal Fab Tools ·

Sandblasting Nozzle Types and Uses

Ceramic, steel and boron carbide nozzles compared by bore size, wear life and air supply, with the sizes the listings state and how to…