Quick Change Disc vs Flap Disc: Which One Should You Buy?
Two twist-on quick change discs and one flap disc set compared on size, grit, backing, pack and tool fit for die grinder work.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
HOMO FABER 50Pcs Die Grinder Sanding Discs9.6/10View on Amazon - 2
Benchmark Abrasives 2" Zirconia Quick Change9.6/10View on Amazon - 3
Benchmark Abrasives 2" Zirconia Quick Change9.6/10View on Amazon
Verdict. Pick the quick change disc side if you work tight areas and contours with a 2-inch die grinder and want a twist-on disc. Pick the flap disc side if you want one set that covers heavy removal through fine finishing with 4 grits and 2 holders.
A weld bead needs blending, a frame needs rust stripped back to bare metal, and the disc on the grinder decides how that work goes. This comparison puts quick change disc vs flap disc side by side, using three listings as concrete examples: two twist-on quick change discs and one flap disc set.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The three listings

HOMO FABER 50Pcs Die Grinder Sanding Discs
A 50-piece flap disc set with 3-inch discs in 4 grits and 2 quick-change holders for drill and die grinder work.
Pros
- 4 grits in one set: 40, 60, 80 and 120
- 2 quick-change holders with reinforced steel shafts
- 3-inch flap discs with zirconia-coated fibers
- Fits drill and die grinder in the 4,500 to 24,000 RPM range
Cons
- No warranty term is stated
- Mixed grits only; no single-grit pack is stated
- No weight is stated
- No holder shaft size is stated

Benchmark Abrasives 2" Zirconia Quick Change
A 25-count set of 2-inch zirconia quick change discs in 36 grit with Male R Type twist-on backing for die grinders.
Pros
- 36 grit, the coarsest grit here, for stock removal
- Male R Type twist-on backing for quick attachment
- 2-inch size for control in tight areas and contours
- Zirconia grains for deburring, leveling and finishing
Cons
- No warranty term is stated
- Single grit only; no other grit in this listing
- No weight is stated
- No RPM range is stated

Benchmark Abrasives 2" Zirconia Quick Change
A 25-count set of 2-inch zirconia quick change discs in 40 grit with Male R Type twist-on backing for die grinders.
Pros
- 40 grit for stock removal, deburring, leveling and finishing
- Male R Type twist-on backing for quick attachment
- 2-inch size for control in tight areas and contours
- Zirconia grains for consistent abrasion
Cons
- No warranty term is stated
- Single grit only; no other grit in this listing
- No weight is stated
- No RPM range is stated
Other welders and gear to compare
Tshya Quick Change Grinding DiscCheck price on Amazon
Benchmark Abrasives 3" Zirconia Quick Change Sanding DiscsCheck price on Amazon
HOMO FABER 50Pcs Die Grinder Sanding DiscsCheck price on Amazon
EZARC Zirconia Flap Disc SetCheck price on Amazon
S SATC 25PCS Quick Change DiscCheck price on Amazon
33 PCS 2" Quick Change Diamond Sanding Discs Set Easy StripCheck price on Amazon
Side by side
| HOMO FABER 50-Piece | Benchmark 36-Grit | Benchmark 40-Grit | |
|---|---|---|---|
| Gear Score | 58 | 57 | 56 |
| Side | Flap disc | Quick change disc | Quick change disc |
| Size | 3 inches | 2 inches | 2 inches |
| Grit | 40, 60, 80, 120 | 36 | 40 |
| Backing | Roll lock with 2 quick-change holders | Male R Type twist-on | Male R Type twist-on |
| Pack | 50 pieces | 25 discs | 25 discs |
| Tool fit | Drill and die grinder, 4,500 to 24,000 RPM | 2-inch die grinder | 2-inch die grinder |
| Thickness | 0.1 inches | 0.039 inches | 0.039 inches |
| Warranty | Not stated | Not stated | Not stated |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 1 November 2026.
Quick change disc vs flap disc: what separates them
The separation starts at attachment. The Benchmark discs twist on with Male R Type backing, while the flap set’s roll lock discs load onto quick-change holders. Size splits the same way: 2 inches for the quick change discs, 3 inches for the flap discs. Grit splits third: each Benchmark listing covers one grit, while the flap set covers 4 grits in one box. Neither side states a warranty term, so warranty does not separate them.
Size and grit
The quick change discs are 2 inches, with control in tight areas and contours stated in the listing. The flap discs are 3 inches. On grit, the quick change side offers 36 grit on one listing and 40 grit on the other, while the flap set offers 40, 60, 80 and 120 grits, with 12 discs in each grit. The flap set labels its 40-grit discs for heavy material removal, its 60-grit discs for medium smoothing, its 80-grit discs for fine finishing and its 120-grit discs for ultra-smooth polishing.
Holders and tool fit
The Benchmark discs fit 2-inch die grinders, and the listing states compatibility with pneumatic and air grinders. The flap set fits a drill or die grinder in the 4,500 to 24,000 RPM range, and it includes 2 quick-change holders with reinforced steel shafts. The Benchmark listings state no RPM range, so RPM does not compare across the sides.
Pack and value
Each Benchmark listing packs 25 discs in one grit. The flap set packs 50 pieces: 12 discs in each of 4 grits plus 2 holders. No listing here states a warranty term or a weight.
Choose the quick change disc side if
- You work tight areas and contours with a 2-inch die grinder.
- You want a disc that twists on and off the tool.
- You want one grit, 36 or 40, for stock removal and deburring.
- You run a pneumatic or air grinder.
Choose the flap disc side if
- You want 4 grits in one set, from 40 through 120.
- You want 3-inch discs.
- You want 2 holders in the box.
- You run a drill or die grinder in the 4,500 to 24,000 RPM range.
Before You Strike an Arc
- Match the disc to the tool: 2-inch discs for 2-inch die grinders, and the flap set for a drill or die grinder in the stated 4,500 to 24,000 RPM range.
- Check the backing before buying: Male R Type twist-on for the Benchmark discs, roll lock discs on quick-change holders for the flap set.
- Check the pack counts: 25 discs in each Benchmark listing, and the flap set with 12 discs in each of 4 grits plus 2 holders.
- Pick the grit for the job: 36 grit and 40 grit for stock removal and deburring, 120 grit for ultra-smooth polishing, as the listings describe them.
FAQ for welders
What is the difference between a quick change disc and a flap disc?
The Benchmark quick change discs are single discs that twist onto the tool with Male R Type backing, as their listings describe them. A flap disc is a set of overlapping flaps on a backing, and the HOMO FABER set loads its roll lock flap discs onto quick-change holders. The flap set uses quick-change holders for swaps, while the Benchmark discs twist on directly.
Which grit removes the most material here?
The lowest grit number here is 36, on the Benchmark 36-grit disc, described for stock removal. The flap set labels 40-grit for heavy removal, 60-grit for medium smoothing, 80-grit for fine finishing and 120-grit for ultra-smooth polishing.
Do these discs fit a die grinder?
The Benchmark discs fit 2-inch die grinders, including pneumatic and air grinders. The flap set fits a drill or die grinder in the 4,500 to 24,000 RPM range stated in its listing.
How many discs come in each pack?
Each Benchmark listing packs 25 discs in one grit. The flap set packs 12 discs in each of 4 grits plus 2 holders, for 50 pieces in total.
Do any of these listings state a warranty?
None of the three listings states a warranty term, so warranty scores zero for all three.
Related: aluminum oxide vs ceramic flap disc, bench grinder vs die grinder, best abrasive pad for paint removal, best abrasive pads for metal, and the metal fab tools hub.
Scoring, line by line
The three listings are scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| HOMO FABER 50-Piece | 9.6 | 28 | 20 | 22 | n/a | 0 |
| Benchmark 36-Grit | 9.6 | 29 | 20 | 20 | n/a | 0 |
| Benchmark 40-Grit | 9.6 | 28 | 20 | 20 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.




