Propane Regulator O Ring Size Chart
The soft-nose POL rings in this guide share an inner size, and the flat gasket is a different shape to check before ordering.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
BOXOB 30pcs Propane O-Rings for Soft Nose POL Seal9.7/10View on Amazon - 2
Hooshing 6PCS Propane O Ring for Soft Nose P.O.L.9.6/10View on Amazon - 3
Timsec Propane Tank Gasket for Soft Nose P.O.L.9.6/10View on Amazon - 4
YUEARN 15Pcs Propane Tank Gasket and 15Pcs O-Rings9.5/10View on Amazon
A regulator that hisses at the fitting, a grill that will not hold a flame, a ring that has gone hard and flat with age: the fix is a seal that matches the fitting face. Propane regulator o ring size comes down to a shared inner size across the sized kits in this guide, with a larger outer size on the flat gasket to tell apart from the round rings.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

BOXOB 30pcs Propane O-Rings for Soft Nose POL Seal
30 soft rubber O-rings for soft-nose POL fittings, with a stated outer size of 0.58 inch and inner size of 0.39 inch.
Pros
- 30 O-rings, the largest count of round rings here
- Stated outer and inner sizes, 0.58 inch and 0.39 inch
- Premium soft rubber, flexible and durable for long term use
- Fits adapters, connectors, valves, regulators and cylinders
Cons
- Thickness is not stated
- O-rings only, no flat gaskets or tape in the box
- One size only, so the old ring must match 0.58 by 0.39 inch
- No warranty term is stated

Hooshing 6PCS Propane O Ring for Soft Nose P.O.L.
6 soft rubber O-rings for soft-nose POL fittings, with a stated outer size of 0.579 inch and inner size of 0.394 inch.
Pros
- Stated outer and inner sizes, 0.579 inch and 0.394 inch
- Soft, wear resistant rubber, not easy to deform or corrode
- Fits adapters, converters and pipe connectors
- Simple swap for the old washer
Cons
- Only 6 rings, the smallest pack here
- Thickness is not stated
- No flat gaskets or tape in the box
- No warranty term is stated

Timsec Propane Tank Gasket for Soft Nose P.O.L.
10 flat soft rubber gaskets for soft-nose POL fittings, with a stated outer size of 0.716 inch and inner size of 0.394 inch.
Pros
- Full sizes stated: outer, inner and thickness in inches and mm
- Flat design gives full contact around the fitting when correctly sized
- Flexible rubber fits the sealing surface of a compatible connector
- 10 pieces cover maintenance and future replacements
Cons
- Flat shape, not a round O-ring
- 0.716 inch outer size is larger than the round rings here
- No PTFE tape or round O-rings in the box
- 10 pieces, fewer than the 30-piece kits

YUEARN 15Pcs Propane Tank Gasket and 15Pcs O-Rings
15 O-rings, 15 gaskets and a roll of PTFE tape for soft-nose POL fittings, with no ring sizes stated.
Pros
- 15 O-rings plus 15 gaskets in a single box
- PTFE tape included as a sealing supplement
- Soft rubber, wear-resistant and not easy to break
- Spares on hand for regular replacement
Cons
- No ring sizes are stated
- No thickness is stated for the rings or gaskets
- The gaskets' shape is not described
- No single fitting size is named, so confirm the POL fit before ordering
Propane regulator o ring size: what the listings state
The sized round O-rings here share an inner diameter of 0.39 inch to 0.394 inch: the BOXOB rings (on Amazon) list 0.39 inch inside and 0.58 inch outside, and the Hooshing rings (on Amazon) list 0.394 inch inside and 0.579 inch outside. The flat Timsec gasket lists 0.394 inch inside, 0.716 inch outside and 0.12 inch thick. The YUEARN set states no ring sizes, so match it against the old ring before ordering.
Round O-ring or flat gasket
The shape matters as much as the size. The Timsec piece is a flat propane tank gasket, not a round O-ring, and the maker states that the flat design gives full contact around the fitting when correctly sized and installed. The BOXOB and Hooshing pieces are round O-rings for soft-nose POL fittings, and the YUEARN set holds both O-rings and gaskets. Check the old seal’s shape before ordering: the flat gasket is made for soft-nose POL fittings that use a flat sealing washer, while the round rings fit soft-nose POL fittings that take a round ring.
How to measure the old ring
Pull the old ring off the fitting and measure the inner diameter across the hole, the outer diameter across the whole ring, and the thickness. Match the shape too, round or flat, and check the original gasket shape and dimensions before ordering. If the old gasket has become worn, hardened, cracked or compressed, replace it rather than reusing it.
Side by side
| Kit | Inner diameter | Outer diameter | Pieces | Gear Score |
|---|---|---|---|---|
| BOXOB 30 O-Rings | 0.39 in | 0.58 in | 30 | 9.7/10 |
| Hooshing 6 O-Rings | 0.394 in | 0.579 in | 6 | 9.6/10 |
| Timsec 10 Flat Gaskets | 0.394 in | 0.716 in | 10 | 9.6/10 |
| YUEARN 30-Piece Set | Not stated | Not stated | 30 | 9.5/10 |
The O-ring kits
The kits below cover the sizes above: round O-rings in the shared inner size, a flat gasket in the larger outer size, and a mixed set with tape for the rest of the fitting.
FAQ for welders
What size O-ring fits a propane regulator?
The sized round O-rings in this guide share an inner diameter of 0.39 inch to 0.394 inch, with outer diameters of 0.58 inch and 0.579 inch. The flat Timsec gasket measures 0.716 inch outside, 0.394 inch inside and 0.12 inch thick. Measure the old ring before ordering, since the YUEARN set states no sizes.
Is a flat gasket the same as an O-ring?
No. The Timsec piece is a flat propane tank gasket, not a round O-ring, and its flat design gives full contact around the fitting when correctly sized and installed. Round O-rings fit soft-nose POL fittings, so check the shape of the old seal before ordering.
How do I measure an O-ring for a propane regulator?
Measure the inner diameter across the hole, the outer diameter across the whole ring, and the thickness, then match the shape, round or flat. The Timsec listing advises checking the original gasket shape and dimensions before ordering.
Do these O-rings fit a propane regulator?
The kits list regulators among the fittings they suit, along with adapters, connectors, valves and cylinders, and each kit is made for soft-nose POL fittings. Check that the regulator connection uses a soft-nose POL fitting before ordering.
What is the PTFE tape for?
The YUEARN set includes a roll of PTFE thread sealing tape, which the maker describes as a sealing supplement when a connector rusts or otherwise needs extra sealing. It comes with 15 O-rings and 15 gaskets in the same box.
Related: best propane gas regulator, what a propane regulator is, can you use an acetylene regulator for propane, and the metal fab tools hub.




