Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Post Vise Parts: Replacement and Repair Guide

Jaws, jaw plates, screws and handles wear out on a vise, and each one can be swapped while the vise body stays on the bench.

Post Vise Parts: Replacement and Repair Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 16" Wire Wheel for Bench Grinder6" Wire Wheel for Bench Grinder9.6/10View on Amazon
  2. 2VEVOR 15L Ultrasonic CleanerVEVOR 15L Ultrasonic Cleaner9.6/10View on Amazon
  3. 3VEVOR 6L Ultrasonic CleanerVEVOR 6L Ultrasonic Cleaner9.6/10View on Amazon

A vise that slips on the work, or a handle that spins without moving the jaw, can mean a part has worn out, not that the whole vise is done. Post vise parts are the pieces that wear: jaws, jaw plates, screws and handles, each made to swap out while the vise body stays on the bench. This guide names each part, shows how to measure for a match, and walks through fitting a replacement step by step.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Post vise parts: what each part does

Each part of a vise has a job, and each wears in its own way. Jaws grip the work, and serrated jaws bite into metal to hold it still. Jaw plates cover the jaw faces and take the wear, so a worn plate can be swapped while the jaw body stays put. The main screw moves the jaw in and out, and the handle turns the screw. A locking screw holds a rotating head in place. When a part wears, the vise loses grip or travel, and replacing that part can bring the vise back to work. The replacement parts listed here are made for bench vises; see the bench vise vs post vise guide for how the two vise types differ.

Side by side

Jaws Jaw plates Screws and handles
What it replaces Worn vise jaws Worn jaw plates Worn screw or handle
Size listed 6 1/2 in wide, 3/4 in high (motoparty) 5-inch plates M8x15 locking screw
Material Aluminum (motoparty jaws) Hardened steel High-strength metal (locking screw)
Fits Older 6 1/2 in reversible gray vises; Yost Model 445 and MV-5 Number-5 Mechanic’s vises Yost 880-D2 and 865-D2 vises; COGNATIVE multi-purpose bench vise
Count 2 1 1

The table above shows the spread of replacement parts the makers list. Jaws and plates are measured in inches and matched to the vise model, while screws are matched by thread size and handles by the vise model they fit. Match the part before ordering, and the repair stays a simple swap.

Name the worn part

Start by finding which part has failed. Worn serrations on the jaws let work slip, and the Yost 445-2 listing names replacement serrated jaws for Bench Vise Model 445 and the MV-5 Homeowners Vise. Worn jaw plates show the same fault, and the IRWIN T5D (on Amazon) listing names replacement jaw plates and screws for Number-5 Mechanic’s Vise, with jaws made from hardened steel and plates fully machined on all load-bearing surfaces. A handle that spins or a screw that binds points to the main screw and handle, and Yost lists a replacement main screw handle for Bench Vise Model 880-D2 and another for Bench Vise Model 865-D2. A rotating head that will not stay put points to the locking screw, and COGNATIVE lists an M8x15 locking screw for the rotating head of a multi-purpose bench vise.

Measure the vise

Measure before ordering, because a part that looks right can still miss by a fraction. The motoparty replacement jaws (on Amazon) list 6 1/2 in wide, 3/4 in high, 7/16 in thick, and 2 1/2 in C-C on the mounting screw holes, with 2 grooves on one side and a reversible fit. The IRWIN jaw plates list 5-inch plates that fit Number-5 Mechanic’s vises. The COGNATIVE locking screw (on Amazon) lists thread size M8x15. Measure the jaw width, the jaw height, the plate size and the hole spacing on the vise in hand, and compare each figure with the listing before ordering. See the bench vise parts guide for the name of each part on the vise.

Match the part by model

Model is the surest match. Yost lists its serrated jaws for Bench Vise Model 445 and the MV-5 Homeowners Vise, and lists its main screw handles for Model 880-D2 and Model 865-D2, each as an original replacement part for the Yost bench vise named. IRWIN lists its jaw plates and screws for Number-5 Mechanic’s Vise, with 5-inch plates. The motoparty jaws list fitment for many older American model 6 1/2 in reversible gray vises, and name Craftsman and Columbian vises. The COGNATIVE locking screw lists fitment for the COGNATIVE multi-purpose bench vise rotating head, with chrome plating and a precise fit. Check the model cast or stamped on the vise body, and match it to the listing.

Fit the part

Take the worn part off, clean the seat it sat on, and fit the new part in its place. Jaw plates go on with the screws the listing includes, and the IRWIN T5D listing names replacement jaw plates and screws together. Jaws with 2 grooves on one side can be turned over for a fresh face, and the motoparty jaws are reversible for that reason. The main screw handle goes on the main screw, and the locking screw threads into the rotating head. Tighten the screws snug, then work the vise through its travel and check that the jaw moves smooth and the handle turns without binding.

Check the repair

Close the jaws on a piece of scrap and check that it holds without slipping. Open and close the vise through its full travel and check that the handle turns the screw without binding. Turn the rotating head and tighten the locking screw, then check that the head stays where it is set. If the work still slips, check the jaw serrations and the plate faces again, and check that the part fitted matches the model and size the listing names.

Vise repair safety. Wear eye protection when cleaning rust and scale from a vise, and keep fingers clear of the jaws while working the handle. Clamp the vise body to the bench before fitting parts, and check that the vise sits steady before putting work in it. A vise that moves on the bench is a vise that needs bolting down before use.

FAQ for welders

What parts wear out on a post vise?

Jaws, jaw plates, screws and handles are the parts that wear. Serrated jaws lose their bite, jaw plates wear on their faces, the main screw and handle wear with use, and a locking screw wears where it holds the rotating head. Each part is listed as a replacement, so the vise body stays in service.

How are vise jaws measured?

Measure width, height, thickness and hole spacing. The motoparty replacement jaws list 6 1/2 in wide, 3/4 in high, 7/16 in thick, and 2 1/2 in C-C on the mounting screw holes. Compare each figure with the jaws on the vise in hand before ordering.

Will replacement jaws fit any vise?

No, fit is by size and model. The motoparty jaws list fitment for many older American model 6 1/2 in reversible gray vises, and name Craftsman and Columbian vises. Yost lists its serrated jaws for Bench Vise Model 445 and the MV-5 Homeowners Vise. Check the model on the vise body.

What is a main screw handle?

It is the handle that turns the main screw and moves the jaw. Yost lists a replacement main screw handle for Bench Vise Model 880-D2 and another for Bench Vise Model 865-D2, each as an original replacement part for the Yost bench vise named.

What size is a vise locking screw?

It depends on the vise. COGNATIVE lists an M8x15 locking screw for the rotating head of its multi-purpose bench vise, with high-strength metal and chrome plating. Check the thread size the vise needs before ordering.

Related: bench vise parts, bench vise types, bench vise vs post vise, best heavy duty bench vise, and the metal fab tools hub.

More buying guides

Welding Tables and Carts ·

Bench Vise Parts: Names and What Each Does

Bench vise parts are the jaws, screw, handle, slide and base that hold work still, and this guide names each one and shows how…