Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Parts of a TIG Welder: Torch, Collets and Consumables

A TIG torch is a handful of parts: a collet grips the tungsten, a gas lens or collet body shapes the gas, a cup directs it at the puddle, and a back cap holds the collet in place.

Parts of a TIG Welder: Torch, Collets and Consumables
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YOBEL 100Pcs TIG Torch Consumables & AccessoriesYOBEL 100Pcs TIG Torch Consumables & Accessories9.7/10View on Amazon
  2. 236 Pcs TIG Welding Torch Tools Accessories Stubby36 Pcs TIG Welding Torch Tools Accessories Stubby9.7/10View on Amazon
  3. 3Alffun 5Pcs TIG Welding 57Y02 Long Back CapAlffun 5Pcs TIG Welding 57Y02 Long Back Cap9.6/10View on Amazon
  4. 4RIVERWELD Welding Cables Connector Fitting 5/8"-18RIVERWELD Welding Cables Connector Fitting 5/8"-189.6/10View on Amazon

A bead that wanders, a cup that fogs, a tungsten that will not stay put: the torch is where a TIG weld is made or lost. The parts of a TIG welder at the torch are the collet and collet body or gas lens, the nozzle or cup, and the back cap, with cables bringing power and gas to the torch. This guide names each part, says what it does, and shows the consumables below that fit the torches listed.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

YOBEL 100Pcs TIG Torch Consumables & Accessories

YOBEL 100Pcs TIG Torch Consumables & Accessories

YOBEL9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 100-piece TIG consumables kit for WP-17, WP-18 and WP-26 torches, with #12 glass cups, stubby gas lens 53N61, alumina nozzles, 13N11 copper collets and back caps in a hard case.

Pros

  • 100 pieces: cups, collets, gas lens, nozzles and back caps in one kit
  • Stubby gas lens 53N61 and #12 glass cup for a wide, visible arc
  • 13N11 copper collets, same threads as the torch takes, per the listing
  • Hard case keeps the parts sorted

Cons

  • No warranty term is stated
  • No stated count for each part type in the 100 pieces
  • Fits some CK torches, not all, per the listing
  • No stated tungsten sizes for the collets
36 Pcs TIG Welding Torch Tools Accessories Stubby

36 Pcs TIG Welding Torch Tools Accessories Stubby

Telooco9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 36-piece TIG torch accessories kit for WP-17, WP-18 and WP-26 torches, with glass cups from #4 to #12, electrode clips and rings, and copper parts.

Pros

  • 36 pieces: shield cups, electrode clips and rings
  • Glass cups from #4 to #12 for different cup sizes
  • Copper parts for good electrical conduction, per the listing
  • Fits WP-17, WP-18 and WP-26 torches

Cons

  • No warranty term is stated
  • No stated count for each cup size
  • Stated uses are carbon steel and some low-alloy steel only
  • No stated gas lens part number
Alffun 5Pcs TIG Welding 57Y02 Long Back Cap

Alffun 5Pcs TIG Welding 57Y02 Long Back Cap

Alffun9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-pack of 57Y02 long back caps, 118 mm long, for 17 and 26 series air cooled torches and 18 series water cooled torches.

Pros

  • 5 long back caps in one pack
  • 118 mm long, per the listing
  • Fits 17 and 26 series air cooled and 18 series water cooled torches
  • Lists Lincoln PTA-17, PTA-18 and PTA-26 torches by name

Cons

  • No warranty term is stated
  • Bullets list the diameter as 3/8 in and 32 mm, which do not agree
  • Back caps only, no cups or collets in the pack
RIVERWELD Welding Cables Connector Fitting 5/8"-18

RIVERWELD Welding Cables Connector Fitting 5/8"-18

RIVERWELD9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-pack of 5/8-18 male cable connector fittings for a WP-26 TIG torch with separate gas and water cables.

Pros

  • 2 fittings in the pack
  • 5/8-18 male thread stated in the title
  • Made for WP-26 torch gas and water separate cables
  • Title, bullets and spec table agree on the size

Cons

  • No warranty term is stated
  • No material stated
  • WP-26 only, no other torch series stated
  • One short bullet, with no install notes

Parts of a TIG welder

A TIG welder has a power source, a torch, and the cables between them. The torch holds the tungsten electrode in a collet, and a collet body or gas lens around the collet shapes the gas flow. An alumina nozzle or a glass cup sits over the collet body and directs the shielding gas at the puddle. A back cap screws on behind the torch head and holds the collet in place. Power and gas reach the torch through cables, joined by fittings like the 5/8-18 connector below.

How the parts fit together

Start at the tungsten. The collet grips the tungsten, the collet body or gas lens threads into the torch head around it, and the cup threads over the collet body. The back cap screws into the back of the torch head and presses the collet into place. Gas flows from the machine through the cable, through the gas lens or collet body, and out of the cup around the tungsten. When a part wears, swap that part, not the whole torch: a worn cup comes off and a new one goes on, which is why the YOBEL kit (on Amazon) carries cups, collets and back caps together, and the Telooco kit (on Amazon) carries cups, clips and rings.

Compare the parts

Gear Score Pieces Fits torches Key part
YOBEL 100-Piece TIG Kit 9.7/10 100 WP-17/18/26 Stubby gas lens 53N61
Telooco 36-Piece TIG Kit 9.7/10 36 WP-17/18/26 Glass cups #4 to #12
Alffun 57Y02 Back Caps 9.6/10 5 17/18/26 series Long back cap 57Y02
RIVERWELD Cable Connector 9.6/10 2 WP-26 Cable connector 5/8-18

The YOBEL kit carries the consumables that wear out: cups, collets, a gas lens and back caps, and the Telooco kit carries cups, clips and rings. The back caps and the cable fitting are for a torch that needs one part, not a whole kit.

Parts and consumables for the bench

The torch parts above are the pieces you swap when a cup cracks, a collet loses its grip, or a back cap goes missing, so the kits and back caps below cover those swaps for WP-17, WP-18 and WP-26 torches while the cable fitting below is made for a WP-26 torch.

How to match parts to your torch

Match the torch series before anything else. The kits here fit WP-17, WP-18 and WP-26 torches, and the YOBEL kit also fits some CK torches. The Alffun back (on Amazon) caps fit 17 and 26 series air cooled torches and 18 series water cooled torches, including Lincoln PTA-17, PTA-18 and PTA-26 torches. Check the thread names on the parts you already have: the YOBEL kit uses 13N collets, a 53N gas lens and screw-on back caps, and the listing states no adapter is needed. When a listing does not name your torch series, ask the maker before you buy, since a part that threads on but seats wrong can leak gas or grip the tungsten poorly.

FAQ for welders

What does the collet do in a TIG torch?

The collet grips the tungsten electrode and holds it centered in the torch head. The YOBEL kit carries 13N11 copper collets. Match the collet to the tungsten and the torch series, since a collet that does not fit will not hold the tungsten steady.

What is a gas lens, and when does it help?

A gas lens is a collet body with a screen that steadies the gas flow out of the cup. The YOBEL kit carries a stubby gas lens, part 53N61, and the listing states it keeps gas flow steady so stainless and aluminum welds stay clean. Reach for the gas lens when the weld needs that steady coverage, and check the thread name, 53N, against your torch.

What does the back cap do?

The back cap screws onto the back of the torch head and holds the collet and tungsten in place. The Alffun 57Y02 is a long back cap, 118 mm long, for 17, 18 and 26 series torches. A long cap leaves room for more tungsten behind the torch head, while a short cap fits where space is tight.

Will these parts fit my torch?

Start with the torch series in the listing. The YOBEL and Telooco kits fit WP-17, WP-18 and WP-26 torches, the Alffun back caps fit 17 and 26 series air cooled torches and 18 series water cooled torches, and the RIVERWELD fitting (on Amazon) is for a WP-26 torch. The YOBEL kit also fits some CK torches. When your torch series is not named, ask the maker before you buy.

When should I swap a cup?

Swap a cup when it is cracked or chipped, or when the arc and gas flow look uneven. The YOBEL listing states you can swap a worn cup mid-job. The kits here carry spare cups, so a worn cup is a quick swap on the bench.

Related: parts of a TIG torch, TIG torch set up, TIG welding cup sizes, best TIG collets, best TIG welder, and the welding consumables hub.

More buying guides

Welders ·

Parts of a MIG Welder Explained

A MIG welder is a set of parts that work together: a power source, a wire feeder, a gun, a ground clamp, a gas…