Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use a Rivet Nut Tool

A rivet nut puts a thread into sheet too thin to tap: drill the hole, thread the insert onto the tool, squeeze to fold it tight, and check the thread before you bolt anything to it.

How to Use a Rivet Nut Tool
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Rivet Nut Tool Kit, 16" Rivnut Tool with 15Rivet Nut Tool Kit, 16" Rivnut Tool with 159.6/10View on Amazon
  2. 2WETOLS Rivet Nut Tool KitWETOLS Rivet Nut Tool Kit9.5/10View on Amazon
  3. 3ASKWAY ASE Pressure Rivet Nut Tool KitASKWAY ASE Pressure Rivet Nut Tool Kit9.4/10View on Amazon
  4. 4Rivet Nut Tool Kit Carbon Steel Mandrel Head SetRivet Nut Tool Kit Carbon Steel Mandrel Head Set9.4/10View on Amazon

Thin sheet metal leaves you with nowhere to put a thread. A bolt needs a nut on the back side, and tapping the sheet itself leaves too little metal to hold. That is the job a rivet nut solves, and learning how to use a rivet nut comes down to drilling a clean hole, threading the insert onto the tool, and squeezing the tool so the insert folds tight against the back of the sheet.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Rivet Nut Tool Kit, 16" Rivnut Tool with 15

Rivet Nut Tool Kit, 16" Rivnut Tool with 15

WOBANK9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 16-inch rivet nut tool kit with 15 mandrels and 290 rivet nuts, plus a wrench, gloves and a carrying case, and the only stated lifetime warranty here.

Pros

  • 15 mandrels cover metric M3 to M12 and SAE 6-32 to 1/2-13
  • 290 rivet nuts included, with metric and imperial sizes in separate boxes
  • Auto release after 2 to 3 squeezes, per the listing
  • Lifetime warranty stated in the listing

Cons

  • No mandrel material grade is stated
  • The split of metric and imperial nuts is not stated
  • Rivet nut material is not stated
  • No stated weight for the full kit
WETOLS Rivet Nut Tool Kit

WETOLS Rivet Nut Tool Kit

WETOLS9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 16-inch hand riveter with 11 metric and SAE mandrels, 110 rivet nuts and a rugged carry case.

Pros

  • 11 interchangeable mandrels in metric and SAE sizes
  • 110 rivet nuts included in the kit
  • Chrome steel mandrels and a 45 carbon steel arm
  • Blow molded carry case keeps every tool in its place

Cons

  • No warranty term is stated
  • No stated insert material or finish
  • Mandrel sizes are listed, but the nut sizes are not broken out
  • No stated weight for the kit
ASKWAY ASE Pressure Rivet Nut Tool Kit

ASKWAY ASE Pressure Rivet Nut Tool Kit

AskWay9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A rivet nut tool set with 770 imperial rivet nuts in 6 sizes, galvanized carbon steel, in a labelled storage box.

Pros

  • 770 rivet nuts, the largest count in this guide
  • 6 imperial sizes from 6-32 to 3/8-16
  • Galvanized carbon steel nuts that the maker lists as rust resistant in storage
  • Long-term service from the maker's operations team

Cons

  • No warranty term is stated
  • Metric inserts are not included
  • Tool length is not stated
  • Mandrel sizes are not listed separately from the nut sizes
Rivet Nut Tool Kit Carbon Steel Mandrel Head Set

Rivet Nut Tool Kit Carbon Steel Mandrel Head Set

IYNRAFW9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A mandrel head set covering metric M3 to M12 for use with a manual wrench or an electric power drill, with no tool or inserts included.

Pros

  • Covers metric M3, M4, M5, M6, M8, M10 and M12
  • GCR15 high-carbon chromium bearing steel with a 12.9-grade alloy mandrel
  • Dual bearing washer design to cut friction
  • Fits a manual hand tool or an electric power drill setup

Cons

  • No tool body or rivet nuts are included
  • No warranty term is stated
  • No stated case or storage

How to use a rivet nut, step by step

Start with the insert and the mandrel that match its thread. Thread the rivet nut onto the mandrel by hand until it sits snug, then slide the nosepiece against the head of the insert. The tool is ready when the insert turns with the mandrel and the nosepiece holds it straight.

Drill the hole in the sheet and clear the chips from both sides. Push the insert through the hole until its head sits flat on the surface. Keep the tool square to the sheet so the insert pulls straight instead of cocking sideways.

Squeeze the handles. The mandrel pulls the threaded end of the insert toward its head, and the body of the insert folds tight against the back of the sheet. The WOBANK kit in the gear section below releases the insert on its own after 2 to 3 squeezes, which is the maker’s stated figure for that tool. On a plain manual tool, keep squeezing until the handles stop moving easily, then unthread the mandrel by turning it back out of the set insert.

Check the thread before you bolt anything to it. Run the bolt in by hand; it should turn freely for the full length of the insert. If it binds, the insert may have spun or folded unevenly, and the fix is to drill it out and set a fresh insert.

Pick the right insert for the sheet

Match the insert thread to the bolt you plan to use, then match the mandrel to the insert. The WOBANK kit below covers metric threads from M3 to M12 and imperial threads from 6-32 to 1/2-13, so a home shop can cover small machine screws up to heavy bolts with one kit. The WETOLS kit (on Amazon) lists 11 mandrels in metric and SAE sizes, and the WOBANK kit lists 15.

Knurled inserts grip better in a round hole than smooth ones. The ASKWAY listing notes its galvanized carbon steel inserts resist rust even after long-term storage. Check the insert length against the sheet: a long insert in thin sheet wastes thread, and a short insert in thick plate may not fold fully.

Side by side

Mandrels Rivet nuts included Tool Warranty
WOBANK 16-Inch Rivet Nut Tool Kit 15, metric and SAE 290 16-inch tool, auto release Lifetime Warranty
WETOLS 16-Inch Rivet Nut Tool Kit 11, metric and SAE 110 16-inch hand riveter Not stated
ASKWAY 770-Piece Rivet Nut Tool Kit Not stated 770 Manual tool, length not stated Not stated
IYNRAFW M3-M12 Mandrel Head Set M3 to M12 nosepieces None, mandrels only Not included, fits manual tool or drill Not stated

The 4 kits below differ mainly in how many mandrels and inserts they include. A mandrel head set on its own, like the IYNRAFW set, suits a shop that already owns a tool and only needs fresh nosepieces.

The rivet nut tool kits

Each kit below handles a step in the job above: the mandrels set the insert size, the tool folds the insert, and the case keeps the sizes sorted for the next repair.

Safety when you drill and set

Drilling and setting. Drilling sheet metal throws sharp chips, so wear eye protection and clamp the work before you drill. Keep fingers clear of the handles while you squeeze, and keep the tool square so the mandrel does not snap under a side load. See the OSHA welding overview for shop safety basics.

FAQ for welders

Can you use a rivet nut in thin sheet metal?

Yes. A rivet nut is made for sheet too thin to tap, because the insert folds against the back of the sheet and gives the bolt a threaded hole to bolt into. The kits in this guide list inserts for metric threads from M3 to M12, which covers the small screws and bolts common in sheet metal work. Drill the hole clean and keep the tool square so the insert sets straight.

What is the difference between a rivet nut and a rivet?

A rivet is a permanent fastener that joins sheets together and leaves no thread behind. A rivet nut folds into the sheet the same way, but leaves a threaded hole you can bolt into and unbolt again. Use a rivet where the joint never comes apart, and a rivet nut where you need to remove the part later for service or repair.

Do you need a special tool to set a rivet nut?

Yes, you need a tool that pulls the mandrel while the nosepiece holds the insert head. The manual kits in this guide do that with long handles, and the IYNRAFW mandrel (on Amazon) set fits a manual wrench or an electric power drill setup.

Can you remove a rivet nut?

Yes, and the usual fix is to drill the insert out and set a fresh insert in the same hole only if the hole is still sound. The how to remove a rivet nut guide covers the steps. If the hole has opened up, move to the next insert size and drill for that size instead.

How do you stop a rivet nut from spinning?

A spinning insert usually means the hole was too large or the insert did not fold fully. Knurled inserts grip better than smooth ones. Set the insert with the tool square to the sheet, and check the bolt by hand before you load the joint.

Related: how to remove a rivet nut, rivet gun vs rivet nut tool, and the metal fab tools hub.

More buying guides