Flux Core vs Stick for Home Garage: Two Wires Compared
Two PGN E71T-11 gasless flux core wires in .030 and .035 inch compared for a home garage, since both picked listings sit on the flux core side of the question.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
PGN E71T-11 .030" Gasless Flux Core Welding Wire 29.5/10View on Amazon - 2
PGN E71T-11 .035" Gasless Flux Core Welding Wire 29.5/10View on Amazon
Verdict. Both wires below are flux core: PGN’s E71T-11 gasless wire in .030 and .035 inch, each on a 2-pound spool. Pick the .030-inch spool when your machine is set up to feed .030-inch wire; pick the .035-inch spool when your setup takes .035-inch wire. The listings state both for mild steel with single and multi-pass welds on T, butt and lap joints, so the diameter your welder feeds decides it.
A home garage weld usually comes from a wire-fed machine or a stick welder, and the choice between flux core vs stick for home garage starts with what is on the bench. This comparison works through the question with two concrete examples, both on the flux core side: PGN’s E71T-11 gasless flux core welding wire in .030 inch and in .035 inch. Neither example is a stick product, so the listings below speak only for the flux core side; the notes alongside say where a stick comparison would need its own listing.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The two wires

PGN E71T-11 .030" Gasless Flux Core Welding Wire 2
A 2-pound spool of E71T-11 gasless flux core wire in 0.030-inch diameter for mild steel, stated for single and multi-pass welds on T, butt and lap joints.
Pros
- E71T-11 gasless wire, so no shielding gas is needed per the listing
- Single and multi-pass welds stated, with T, butt and lap joints named
- 0.030-inch diameter and 2-pound spool stated in title and bullets
- Packaging described as tangle-resistant for storage and feeding
Cons
- No duty cycle stated
- No rated thickness stated
- No warranty term stated

PGN E71T-11 .035" Gasless Flux Core Welding Wire 2
A 2-pound spool of E71T-11 gasless flux core wire in 0.035-inch diameter for mild steel, stated for single and multi-pass welds on T, butt and lap joints.
Pros
- E71T-11 gasless wire, so no shielding gas is needed per the listing
- Single and multi-pass welds stated, with T, butt and lap joints named
- 0.035-inch diameter and 2-pound spool stated in title and bullets
- Spool dimensions of 4.5 x 4.5 x 2 inches stated
Cons
- No duty cycle stated
- No rated thickness stated
- No warranty term stated
- Fewer application details than the .030 listing's bullets
Other welders and gear to compare
GNI Multiprocess Portable MINI WelderCheck price on Amazon
ARCCAPTAIN 130A Flux Core Welder MIG Welder 110V Gasless MIGCheck price on Amazon
Bestarc 145A MIG WelderCheck price on Amazon
160Amp 3 IN 1 WelderCheck price on Amazon
145A MIG WelderCheck price on Amazon
SOARFLY 135A MIG WelderCheck price on Amazon
Side by side
| Wire | Gear Score | Diameter | Spool |
|---|---|---|---|
| PGN E71T-11 .030 Wire | 9.5/10 | 0.030 inch | 2 lb |
| PGN E71T-11 .035 Wire | 9.5/10 | 0.035 inch | 2 lb |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 23 October 2026. Neither listing states a duty cycle, a rated thickness, a CSA, UL or ETL listing, or a warranty term.
Flux core vs stick for home garage
The honest frame for this comparison is that both picked listings are flux core wires, not a flux core wire against a stick electrode. What the two listings state about the flux core side is consistent: E71T-11 wire for gasless welding, with the flux filling acting as the shielding agent so no external shielding gas is needed, and a formulation the maker says protects the weld pool and supports welding outdoors. For the stick side of the keyword, there is no example listing here, so any stick comparison has to be made against a stick product’s own listing, not against these two spools.
Wire diameter
This is the one stated difference between the two spools: 0.030 inch against 0.035 inch, both E71T-11. The .030 listing states its diameter in the title, the bullets and the spec table, which also gives an item weight of 2.23 pounds against the 2 lb in the title and bullets. The .035 listing is consistent everywhere: 0.035 inch and 2 pounds, and it alone states spool dimensions of 4.5 x 4.5 x 2 inches. The .030 listing carries the more detailed application notes, naming professional welding, fabrication, metalworking, maintenance, repair and DIY projects, while the .035 listing names professional welders, metalworking hobbyists and DIY enthusiasts. For a broader look at wire sizes, see 030 vs 035 flux core wire.
Gasless and outdoor use
Both listings describe gasless welding with no external shielding gas. The .030 listing says the flux core formulation helps protect the weld pool and supports reliable welding performance in outdoor environments; the .035 listing says the flux filling acts as a shielding agent to create welds and calls the wire suited for outdoor use. This is the practical core of the flux core side for a home garage: no gas cylinder to buy, keep or refill, according to the listings. The comparison with stick on outdoor work is covered in flux core vs stick for outdoor use.
Spool size and packaging
Both wires come on a 2-pound spool, trusting the title and bullets over the .030 spec table’s 2.23-pound figure. Only the .035 listing states spool dimensions: 4.5 x 4.5 x 2 inches. Both listings describe packaging meant to prevent tangling during storage and use. New to buying wire by the spool? See best flux core wire for beginners.
Choose the .030-inch wire if
- Your machine is set up to feed .030-inch wire.
- You want the listing with the more detailed application notes, naming professional welding, fabrication, metalworking, maintenance, repair and DIY projects.
- You are fine with the weight contradiction in the spec table and go by the 2 lb in the title and bullets.
Choose the .035-inch wire if
- Your machine is set up to feed .035-inch wire.
- You want stated spool dimensions (4.5 x 4.5 x 2 inches) to check against your spool holder.
- You prefer the listing whose spec table agrees with its title on weight: 2 pounds.
Before You Strike an Arc
- Match the wire diameter to what your drive rolls and contact tips are set for: 0.030 inch or 0.035 inch, as each listing states.
- Confirm a 2-pound spool fits your machine’s spool holder before ordering.
- Keep the spool in its packaging to prevent tangling, as the listings describe.
- Both wires are stated for mild steel only; the listings do not name other metals.
- Neither listing states a duty cycle, so check your welder’s own rating before long welds.
FAQ for welders
Can I use these wires with shielding gas?
Both listings describe E71T-11 gasless wire: the flux filling shields the weld pool, so no external shielding gas is needed. Neither listing describes a gas-shielded use for these spools.
What is the difference between the .030 and .035 wires?
The stated difference is the wire diameter: 0.030 inch against 0.035 inch. Both are E71T-11 gasless wires for mild steel on 2-pound spools, with single and multi-pass welds stated on T, butt and lap joints. Buy the diameter your machine is set up to feed.
Do the listings state a duty cycle or thickness rating?
No. Neither listing states a duty cycle or a rated thickness. The .030 listing names T, butt and lap joints for single and multi-pass welds; the .035 listing names the same joints and passes.
Can I weld outdoors with these wires?
The listings state the gasless flux core formulation protects the weld pool and supports welding performance in outdoor environments. That is the outdoor case stated for both spools.
Related: flux core vs MIG for outdoor use, best flux core wire under 30, and the welding consumables hub.
Scoring, line by line
Both wires are scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| PGN E71T-11 .030 Wire | 9.5 | 28 | 19 | 19 | n/a | 0 |
| PGN E71T-11 .035 Wire | 9.5 | 27 | 19 | 19 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




