Cowhide vs Split Leather Welding Gloves: Which One Should You Buy?
Cowhide vs split leather welding gloves explained with two stated gloves: leather grade, heat ratings, EN standards and cuff length compared.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Black Stallion9.6/10View on Amazon - 2
Wells Lamont Leather Welding Gloves9.6/10View on Amazon - 3
Leather Welding Jacket9.5/10View on Amazon - 4
Cowhide Welding GlovesView on Amazon - 5
MOUNTAIN ESSENTIALS Leather Work GlovesView on Amazon - 6
SAFEGEAR Cowhide Leather Work Gloves with Keystone ThumbView on Amazon - 7
Black Stallion Unisex Adult Top Grain Leather Cowhide MigView on Amazon - 8
Cowhide Leather Work GlovesView on Amazon
Cowhide vs split leather welding gloves: split leather is the inner layer of the cowhide, rougher and usually thicker than the top grain, and both gloves in this guide state split cowhide. The OZERO states 1.2 mm split cowhide with stated EN ratings; the Cuwiny states a split palm with a stated 1112F heat figure. For the stated standards, the OZERO is the pick; for the stated cuff length, the Cuwiny is.
Other welders and gear to compare
Wells Lamont Leather Welding GlovesCheck price on Amazon
Cowhide Welding GlovesCheck price on Amazon
MOUNTAIN ESSENTIALS Leather Work GlovesCheck price on Amazon
SAFEGEAR Cowhide Leather Work Gloves with Keystone ThumbCheck price on Amazon
Black Stallion Unisex Adult Top Grain Leather Cowhide MigCheck price on Amazon
Cowhide Leather Work GlovesCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The difference in one paragraph
A cowhide is split into layers: the top grain is the smooth outer layer, and split leather is the fibrous inner layer. Split leather is usually thicker and rougher, and it takes heat and abrasion well at the cost of a coarser feel. Both listings here state split cowhide: the OZERO states 1.2 mm split cowhide with a cotton lining and aluminum foil, and the Cuwiny states a split palm with a cotton liner and aluminum foil. Neither listing states top grain, so the stated comparison is split against split.
Side by side
| Glove | Length | Leather | Heat rating | Standards | Warranty |
|---|---|---|---|---|---|
| OZERO | 14 in | 1.2 mm split cowhide | 932F / 500C 15+ s | EN407 43314X, EN388, EN12477 A | Not stated |
| Cuwiny | 16 in | Split palm leather | 1112F | Not stated | Not stated |
The stated heat figures are the maker’s claims; always check the listing’s stated rating before hot work. Listings were collected 21 October 2026.
When the OZERO is the better choice
The OZERO states 1.2 mm split cowhide with a reinforced palm, Kevlar stitching and a cotton lining with air-isolated aluminum foil. The listing states EN407 43314X for 500C/932F dry heat surfaces for 15+ seconds, EN407 flame behavior level 4 and small splash level 4, plus EN388 abrasion, tear and puncture at level 3 each. The listing states EN12477 Type A with Dexterity 2. For the stated standards, the OZERO is the only pick that names them.
When the Cuwiny is the better choice
The Cuwiny states a 16 in glove with a split palm, Kevlar stitching and a hook and loop closure, the longest stated cuff here. The title states 1112F heat resistance. The spec table states overall item dimensions of 16 x 6 x 0.3 in and 14.89 ounces, a heavyweight fabric class and hand wash care. The listing states no bullets and no standards. For the stated cuff length and the stated 1112F figure, the Cuwiny is the pick.
The two gloves as stated
The OZERO 932F states a 14 in glove in brown with a wing thumb, ambidextrous, medium weight fabric and double stitching. The stated uses run from welding to BBQ, fireplace and forge work. The warranty description states it depends on its condition, which is not a concrete term, so warranty scores zero. The Cuwiny states a yellow and black 16 in glove, ambidextrous and right hand orientation, with cut, oil and puncture resistance stated. Its warranty points to a warranty page with no term, so warranty scores zero there too.
How to tell cowhide vs split leather welding gloves apart
Read the stated material line on the listing. The OZERO states genuine cowhide split leather with an insulated lining; the Cuwiny states leather with a split palm. If the listing states no grain, treat it as unstated rather than assuming top grain. The checkable leather thickness figure is the OZERO’s stated 1.2 mm split cowhide. The Cuwiny states no leather thickness figure: its 16 x 6 x 0.3 in figure is overall item dimensions, not leather thickness, so no leather thickness comparison between the two gloves is possible. Match the stated material to the work: the OZERO states EN ratings for hot work, the Cuwiny states none.
What the EN ratings mean
The OZERO listing states EN407 43314X, which the listing ties to 500C/932F dry heat handling for 15+ seconds, flame behavior level 4 and small splash level 4. The listing states EN388 abrasion, tear and puncture at level 3 each, and EN12477 Type A with Dexterity 2. The Cuwiny states no EN ratings. For the stated ratings, the OZERO is the only glove that names them; the Cuwiny rests on its stated 1112F title figure alone.
Fit and construction
The OZERO states a regular fit with a wing thumb and ambidextrous hand orientation, in a 14 in size as 1 pair. The spec table states a medium weight fabric class, no stretch, double stitching and a cotton glove liner. The Cuwiny states a one-size fit with a positive fit sentiment, a wing thumb, ambidextrous and right hand orientation, and a heavyweight fabric class with Kevlar stitching. The OZERO states a unit count of 2 against a stated number of items of 1, a contradiction in the spec table worth noting. For the stated fit detail, the OZERO names the most.
Lining and water
The OZERO states a cotton lining with air-isolated aluminum foil and insulated cotton with aluminum film in the palm structure. The Cuwiny states a cotton glove liner with leather and aluminum foil in the material features. Both state Not Water Resistant, so neither is a wet-work glove. The OZERO states heat resistant, flame retardant, puncture resistant and cut resistant material features; the Cuwiny states cut resistant, oil resistant and puncture resistant. For the stated lining, both name cotton and aluminum foil.
Care
The Cuwiny states hand wash care instructions. The OZERO states no care instructions in the shown text. The Cuwiny states a heavyweight fabric class against the OZERO’s stated medium weight. For stated care, the Cuwiny is the only one that names it.
FAQ for welders
Which states a heat rating?
The OZERO states 932F/500C for 15+ seconds with stated EN407 figures. The Cuwiny states 1112F in its title with no stated standard.
Which states the longer cuff?
The Cuwiny states 16 in with a hook and loop closure. The OZERO states 14 in with a long cuff.
Which states EN ratings?
The OZERO states EN407 43314X, EN388 level 3 figures and EN12477 Type A. The Cuwiny states no EN ratings.
Which states Kevlar stitching?
Both state Kevlar stitching: the OZERO states it with a reinforced palm, and the Cuwiny states it with a split palm.
Are either stated as top grain?
No. Both state split cowhide or split palm. Neither states top grain.
Related: our best leather welding gloves and best welding gloves for dexterity.
Back to all welding safety gear reviews.




