Best Welding Square Fixture (2026): 5 Fixture Pin Picks for 5/8-Inch Tables
Five fixture pin sets and clamp kits for 5/8-inch welding tables, compared on piece count, pin size, material and stated clamp force.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMoxweyeni T-Handle Clamp Kit9.5/10View on Amazon - 2
Most PiecesYaocom 15-Piece Pin Set9.5/10View on Amazon - 3
Best for Round TubeRCTUTEIAO 12-Piece Pin Set9.4/10View on Amazon - 4
Quickest ChangeTeche Ball Lock Pins 4-Pack9.4/10View on Amazon
A frame goes together square or it does not, and the difference shows up when a corner pulls out of true and the door or gate binds. A welding square fixture holds tube and angle in place on the table while the bead goes in, so the joint stays where it was set. This guide compares the best welding square fixture picks for tables with standard holes, scored on fit, material and what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Moxweyeni T-Handle Clamp Kit: Two T-handle clamps plus 12 pins, a stated 300 lb clamp force, and an 8-1/2 inch opening. Check price on Amazon
- Most Pieces Yaocom 15-Piece Pin Set: 15 carbon steel pins with a black zinc coating, deep cold and heat treated. Check price on Amazon
- Best for Round Tube RCTUTEIAO 12-Piece Pin Set: 6 V-groove pins for round tube and 6 square pins, in aluminum alloy that sheds slag. Check price on Amazon
- Quickest Change Teche Ball Lock Pins 4-Pack: Push-button ball lock pins that fit 5/8-inch and 16 mm tables without threading. Check price on Amazon
The machines

Moxweyeni 2 Pcs Welding Fixture with T-handle 12
A 2-clamp kit with 12 fixture pins, a stated 300 lb clamp force, and an 8-1/2 inch opening for 5/8-inch tables.
Pros
- Two T-handle clamps plus 12 pins in one kit
- Stated 300 lb clamp force with an 8-1/2 inch opening and a 3-1/4 inch throat depth
- 6 V-groove pins for round tube and 6 square pins for square tube
- High-carbon steel guideways and Q235 arms, chrome-plated and black anodized; pins are high-temperature aluminum alloy that sheds slag
Cons
- Aluminum alloy pins are softer than the steel pins here and can dent under heavy stock
- Only 2 clamps in the kit, so a frame with several joints needs more clamps than the kit holds
- 300 lb is a maximum rating, and the listing does not say how it was measured
- No warranty term is stated

Yaocom 15 Pcs 5/8" x 1" x 1.5" Welding Table
A 15-piece set of carbon steel fixture pins with a black zinc coating, sized 5/8 x 1 x 1.5 inches.
Pros
- 15 pins, the largest count here
- Carbon steel, deep cold and heat treated
- Black zinc coating for rust resistance
- 1.5 inch height with a 1 inch outer diameter and a 5/8 inch bottom diameter for a secure hold
Cons
- No V-groove shape for round tube is stated
- No clamp is included, so holding force comes from the pins alone
- No stated clamp force or load rating
- No warranty term is stated

RCTUTEIAO Welding Table Fixture Pins 12 Pcs 5/8 x
A 12-piece aluminum alloy pin set with 6 square pins and 6 V-groove pins for square and round tube.
Pros
- 6 square pins and 6 V-groove pins cover square and round tube
- Aluminum alloy sheds weld slag, so the pins stay clean between jobs
- High precision machining for a tight fit in the table holes
- 12 pins for 5/8-inch tables, with MIG work stated
Cons
- Aluminum alloy is softer than steel and can dent under heavy stock
- No clamp is included, so holding force comes from the pins alone
- No stated clamp force or load rating
- 12 pieces is fewer than the 15-piece set here

Teche 5/8" Quick-Release Ball Lock Pins
A 4-pack of push-button ball lock pins in quenching treated alloy steel, sized for 5/8-inch and 16 mm tables.
Pros
- Push-button quick release for fast setup and teardown
- Fits both 5/8-inch and 16 mm tables
- Hardened ball bearings expand and lock under the table surface
- Quenching treated alloy steel for wear resistance
Cons
- Only 4 pins in the pack
- No square or V-groove stops are included, pins only
- The push-button ball lock has moving parts, where a solid pin has none
- No stated holding force

Hicarer 10 Pcs 5/8" x 1" x 1.5" Welding Table
A 10-piece set of 45 carbon steel fixture pins with a galvanized surface, sized 5/8 x 1 x 1.5 inches.
Pros
- 45 carbon steel with a galvanized surface
- 10 pieces for positioning, alignment and repeat setups
- Sized for 5/8-inch tables, the common hole size
- Pin size of 1.5 x 1 inches for a steady stop
Cons
- No V-groove shape for round tube is stated
- No clamp is included, so holding force comes from the pins alone
- No stated holding force or load rating
- Fewer pieces than the 15-piece set here
Spec sheet comparison
| Model | Gear Score | Pieces | Pin size | Material | Clamp force | Type | Warranty |
|---|---|---|---|---|---|---|---|
| Moxweyeni T-Handle Clamp Kit | 9.5/10 | 2 clamps + 12 pins | 5/8 in | High-carbon steel, Q235 steel, aluminum pins | 300 lb | Clamps + pins | None stated |
| Yaocom 15-Piece Pin Set | 9.5/10 | 15 | 5/8 x 1 x 1.5 in | Carbon steel, black zinc | Not stated | Pins | None stated |
| RCTUTEIAO 12-Piece Pin Set | 9.4/10 | 12 | 5/8 x 1 x 1.5 in | Aluminum alloy | Not stated | Pins | None stated |
| Teche Ball Lock Pins 4-Pack | 9.4/10 | 4 | 5/8 in | Alloy steel, quenching treated | Not stated | Ball lock pins | None stated |
| Hicarer 10-Piece Pin Set | 9.3/10 | 10 | 5/8 x 1 x 1.5 in | 45 carbon steel, galvanized | Not stated | Pins | None stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 21 November 2026.
Buying guide: the best welding square fixture
Pin size and table holes
Every pick here is made for 5/8-inch holes, the common size on modular fixture tables. and two picks also state a 16 mm fit for metric tables. Check the hole size on the table before ordering, since a pin that is too small will rock and a pin that is too large will not drop in.
Square pins and V-groove pins
Square pins stop square tube and angle against a flat face, while V-groove pins cradle round tube so it cannot roll while it is tacked. Two kits here include both shapes, which covers a mixed job without a second order.
Material: steel or aluminum
Steel pins take knocks and hold up under heavy stock, and the steel sets here are carbon steel or alloy steel with a coating against rust. Aluminum pins are lighter, and weld slag does not stick to them as readily. Either material works for light layout work; for heavy plate, steel is the safer choice.
Clamps or pins alone
Pins locate the work; they do not squeeze it. A clamp kit adds holding force, and the one clamp kit here states 300 lb with an 8-1/2 inch opening and a 3-1/4 inch throat depth. For thin tube and light angle, pins alone can be enough; for a frame that must stay put, a kit with clamps does more.
Piece count
Sets here run from 4 pieces to 15 pieces. More pins let you set more stops at once, which matters on a frame with several joints. Count the stops the job needs before choosing a pack size.
Use as directed. Check that every pin drops cleanly into the table holes before striking an arc, and keep hands clear of the joint while clamps are set. Spatter falls through fixture holes, so keep the floor under the table clear of anything that can burn. Never exceed a stated clamp force, and keep cords and gas hoses where hot slag cannot land on them.
Before You Strike an Arc
- Check the table holes against the pin size: every pick here is made for 5/8-inch holes, and two also fit 16 mm tables.
- Count the pins against the job: a frame with several joints needs more stops than one jig.
- For the clamp kit, check the 8-1/2 inch opening and 3-1/4 inch throat depth against the work before tightening the T-handle.
- Brush slag off the pins after each job, since buildup keeps pins from seating fully in the holes.
- Ground the welder to the workpiece itself, since coated pins can break the ground path.
FAQ for welders
What is a try square in welding?
A try square is a layout tool that checks whether two faces meet at a right angle. In welding, a square fixture does the same job on the table: pins and stops hold tube at a right angle while the joint is tacked, so the frame stays square after the weld cools.
What size pins fit a 5/8-inch welding table?
Pins sized for 5/8-inch holes, which is what every pick here uses. Two picks also state a 16 mm fit, so they drop into metric tables with the same hole size. Measure the table holes before ordering, since a pin that is too small will rock in the hole.
Do fixture pins work for round tube?
Plain pins hold square tube against a flat face, but round tube needs a V-groove to keep it from rolling. Two kits here include V-groove pins, 6 in each kit, alongside square pins for square tube.
What is the difference between a square pin and a V-groove pin?
A square pin gives a flat face for square tube and angle to sit against. A V-groove pin has a notch that cradles round tube and stops it rolling. Kits that include both shapes cover square and round stock without a second order.
How many fixture pins do I need?
Sets here run from 4 pieces to 15 pieces. One jig may need only a few pins, while a frame with several joints needs a stop at each corner. Count the joints on the job before choosing a set.
Related: welding square fixture, cast iron vs steel welding square, welding magnets for squaring, angle clamps for welding, best welding clamps for fabrication, types of welding clamps, best 6 inch combination square, best 90 degree corner clamp, fixture table vs steel plate welding table, best welding vise for table.
Scoring, line by line
Each fixture is scored out of 10 on performance, build, value, safety listing and warranty, Fixture pins carry no electrical safety listing and no listing here states a warranty term, so every pick scores zero on both; the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Moxweyeni T-Handle Clamp Kit | 9.5 | 30 | 21 | 21 | 0 | 0 |
| Yaocom 15-Piece Pin Set | 9.5 | 29 | 21 | 21 | 0 | 0 |
| RCTUTEIAO 12-Piece Pin Set | 9.4 | 28 | 20 | 21 | 0 | 0 |
| Teche Ball Lock Pins 4-Pack | 9.4 | 28 | 21 | 19 | 0 | 0 |
| Hicarer 10-Piece Pin Set | 9.3 | 26 | 19 | 19 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.




