Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Welding Square vs Combination Square: Which One Should You Buy?

A magnetic welding square and a combination square compared head to head on holding power, angles, graduations, build and warranty for fab shop work.

Welding Square vs Combination Square: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Starrett Steel Combination Square with SquareStarrett Steel Combination Square with Square9.7/10View on Amazon
  2. 2Strong Hand Tools MLD600 90° Fixed Angle MagneticStrong Hand Tools MLD600 90° Fixed Angle Magnetic9.6/10View on Amazon

Verdict. Pick the Strong Hand MLD600 magnetic square for fit-up and tacking: its magnets hold sheet, pipe and flat stock at 90 degrees with a stated 40 lbs of pull. Pick the Starrett 11H-12-4R combination square for layout and checking: its 12 inch blade reads to 64ths. The Starrett scores higher here on graduations and build; the Strong Hand is the one that holds the work.

A frame that is out of square at fit-up stays out of square after welding, which is why the welding square vs combination square question comes down to holding versus marking. This comparison puts the Strong Hand Tools MLD600 magnetic welding square against the Starrett 11H-12-4R combination square on what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The two squares

Starrett Steel Combination Square with Square

Starrett Steel Combination Square with Square

Starrett9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12 inch hardened steel combination square with 4R graduations to 64ths, cast iron head, scriber and spirit level.

Pros

  • 12 inch hardened steel blade with 4R graduations down to 64ths
  • Cast iron head with reversible lock bolt, scriber and spirit level
  • Scribes, measures, tri-squares, miters and gauges depth and height
  • One Year warranty on defects in material and workmanship stated

Cons

  • Marks and measures but does not hold work like a magnetic square
  • No shorter blade option in this listing
  • 1.2 pounds, noticeable in an apron pocket
  • Warranty wording is not counted as a concrete term for scoring
Strong Hand Tools MLD600 90° Fixed Angle Magnetic

Strong Hand Tools MLD600 90° Fixed Angle Magnetic

Strong Hand Tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6 inch magnetic welding square with 40 lbs of pull for holding stock at 90 degrees during fit-up.

Pros

  • 40 lbs pull force holds sheet, pipe and flat stock for fit-up
  • 90 degree fixed angle, plus 30 and 60 degree angles
  • Inside and outside magnets; mounting holes link two units
  • Hex hole gives breakaway leverage

Cons

  • No warranty term is stated
  • Holds work but does not mark or measure like a combination square
  • 6 inch size; no larger option in the listing
  • Magnets attract grinding dust and spatter in the shop

Other welders and gear to compare

Side by side

Square Gear Score Type Size Material Warranty
Starrett 11H-12-4R Square 9.7/10 Combination 12 in blade Steel, cast iron Stated, not counted
Strong Hand MLD600 Square 9.6/10 Magnetic 6 in Metal Not stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 22 October 2026. Neither listing states a warranty term the scoring counts.

Welding square vs combination square: holding vs marking

The MLD600 is a fit-up tool: inside and outside magnets, built as two independent units, hold sheet metal, round pipe and square, angled or flat stock at 90 degrees while you tack. The Starrett is a layout tool: its square head scribes right angles and parallel lines, measures, tri-squares, miters, and gauges depth and height. One holds the work, the other marks it; see our best welding magnets for tack welding picks for more holding options.

Angles and graduations

The MLD600 holds fixed angles: 90 degrees, with 30 and 60 degrees. The Starrett has no magnet and no fixed angle; instead its 12 inch blade carries a 4R graduation with 8ths, 16ths, quick-reading 32nds and 64ths. Do not read a winner here: the listings state different kinds of specs, and neither states the other’s.

Size, weight and build

The MLD600 measures 6 by 4.33 by 0.79 inches in metal, with mounting holes to link two magnets for fixturing and a hex hole for breakaway leverage. The Starrett pairs a 12 inch hardened steel blade with a cast iron head, reversible lock bolt, scriber and spirit level, and weighs 1.2 pounds. The MLD600 listing states no weight. See our cast iron vs steel welding square comparison for more on square materials.

Warranty

Neither square earns warranty points: the Strong Hand listing states no warranty term, and the Starrett listing’s “One Year on defects in material and workmanship” was not counted as a concrete term. Keep the receipt either way; an unstated or uncounted term is not a promise.

Choose the Strong Hand MLD600 if

  • You tack frames, boxes and brackets and want them held at 90 degrees.
  • You work with sheet, round pipe and flat or angled stock.
  • You want 30 and 60 degree angles as well as 90.
  • You like linking two magnetic squares for bigger fixturing.

Choose the Starrett 11H-12-4R if

  • You lay out cuts, scribe lines and check parts for square.
  • You want graduations down to 64ths on a 12 inch blade.
  • You use the scriber and spirit level on the head.
  • You want a cast iron head with a reversible lock bolt.

FAQ for welders

Can a magnetic square replace a combination square?

No. The MLD600 holds work at 90 degrees with a stated 40 lbs of pull but carries no graduations, while the Starrett marks and measures down to 64ths but holds nothing. They do different jobs, and most fab work wants both on the bench.

What angles does the Strong Hand MLD600 hold?

It holds 90 degrees fixed, with 30 and 60 degrees. The inside and outside magnets are two independent units, and mounting holes let you link two squares together for fixturing.

How fine are the Starrett 11H-12-4R graduations?

The 4R graduation reads 8ths, 16ths, quick-reading 32nds and 64ths on the 12 inch hardened steel blade. The cast iron head adds a reversible lock bolt, scriber and spirit level for layout work.

Does the MLD600 state a warranty?

No warranty term is stated in the Strong Hand listing. The Starrett listing states a one year warranty on defects in material and workmanship, but it was not counted as a concrete term for scoring, so neither square earns warranty points.

Which is better for tacking up a frame?

The MLD600. Its magnets hold sheet, pipe and flat stock at 90 degrees while you tack, with 40 lbs of pull stated. The Starrett then checks the result, since it marks and measures but does not hold.

Related: best combination square for metal work, best welding magnets for tack welding, cast iron vs steel welding square, and the metal fab tools hub.

Scoring, line by line

Both squares are scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Starrett 11H-12-4R Square 9.7 32 22 20 n/a 0
Strong Hand MLD600 Square 9.6 29 20 20 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

Before you strike an arc. Check the MLD600 against a known square on arrival, and wipe grinding dust off the magnets so they seat flat. Confirm the Starrett head locks tight on the blade before marking, and keep the scriber capped in the apron pocket.

More buying guides