Best Welding Magnets for Tack Welding (2026)
Best welding magnets for tack welding: four magnetic holders compared by pull force, adjustability and value.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best overallMagTab Jumbo9.7/10View on Amazon - 2
Switch pickYESWELDER Arrow9.6/10View on Amazon - 3
35-lb pickGrasshopper9.6/10View on Amazon - 4
Corner pick90 Degree Neodymium9.6/10View on Amazon
Tack welding needs a third hand, and the best welding magnets for tack welding hold the work while both of yours are busy. We compared four magnetic holders by pull force, adjustability and value, using only what each listing publishes.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Quick picks
- Best overall MagTab Jumbo: 80 lb pull, adjustable Check price on Amazon
- Switch pick YESWELDER Arrow: On and off switch, 44 lb Check price on Amazon
- 35-lb pick Grasshopper: Brass tip, spring arm Check price on Amazon
- Corner pick 90 Degree Neodymium: 90-degree, neodymium Check price on Amazon
The machines

Strong Hand Tools MNT15 MagTab Jumbo Adjustable
An adjustable magnetic tab holder with up to 80 lb of holding force.
Pros
- 80 lb max pull stated
- Adjustable stated
- Parallel or perpendicular stated
- For tack welding stated
Cons
- 80 lb max pull stated
- Adjustable tab holder stated
- Parallel or perpendicular stated
- Rated on 0.08 in flat steel

YESWELDER Switchable Arrow Welding Magnet 2 Pc
Switchable arrow welding magnets, 2 pc, up to 44 lb with on and off switch.
Pros
- On and off switch stated
- Up to 44 lb stated
- Arrow-shaped stated
- 2 pc stated
Cons
- Up to 44 lb stated
- On and off switch stated
- Arrow-shaped stated
- 2 pc stated

Strong Hand Tools Grasshopper Magnetic Welding
A magnetic welding finger with 35 lb pull and a brass contact tip.
Pros
- 35 lb pull stated
- Brass contact tip stated
- Spring-loaded arm stated
- V-pad base stated
Cons
- 35 lb pull stated
- Brass contact tip stated
- Spring-loaded arm stated
- V-pad base stated
Other welders and gear to compare
YESWELDER 25 lb and 50 lb Welding Magnet-4 Pc of WeldingCheck price on Amazon
Strong Hand Welding MagnetCheck price on Amazon
Magnetpro Multipurpose Switch Magnet 220 LB Pull-Off ForceCheck price on Amazon
TOOLIOM Arrow Welding Magnet SetCheck price on Amazon
TOOLIOM Arrow Welding MagnetsCheck price on Amazon
Spec sheet comparison
| Magnet | Weld Score | Pull force | Type |
|---|---|---|---|
| MagTab Jumbo | 9.7/10 | 80 lb | Adjustable tab holder |
| YESWELDER Arrow | 9.6/10 | 44 lb | Switchable arrow |
| Grasshopper | 9.6/10 | 35 lb | Welding finger |
| 90 Degree Neodymium | 9.6/10 | Not stated | 90-degree holder |
Details as published on each listing, collected 21 October 2026.
How to choose the best welding magnets for tack welding
Pull force
The MagTab Jumbo delivers up to 80 lb of holding force, rated on 0.08 in flat steel, the strongest here. The YESWELDER arrow magnets hold up to 44 lb (20 kg) with an on and off switch. The Grasshopper holds 35 lb with a brass contact tip. The 90-degree neodymium magnets state no pull figure. Stronger holds suit heavier parts.
Switchable or fixed
The YESWELDER arrow magnets have an on and off switch, so you can place and release them cleanly. The MagTab Jumbo is adjustable for parallel or perpendicular tabs. The Grasshopper has a spring-loaded arm that self-adjusts. Switchable magnets are easiest to reposition.
Shape and job
The 90-degree neodymium magnets create 90-degree corners from the outside, leaving the inside clear for tack welds. The MagTab Jumbo holds tabs and small parts. The Grasshopper steadies parts at a single point. Match the shape to the joint.
Before You Strike an Arc
- Set the angle first: the YESWELDER arrow magnets hold 45, 90 and 135 degrees, and the neodymium magnets set 30, 60 and 90 degrees from their outer edges.
- Mind the heat limit on the MagTab Jumbo: the listing says remove it before completing the weld and avoid heat sources of 175°F (80°C) and above.
- Match the base to the surface: the MagTab and Grasshopper V-pad bases adapt to round, flat and angled surfaces, and the Grasshopper base also adapts to square surfaces.
- Keep the joint clear: the Grasshopper brass tip holds at a single point, and the neodymium magnets hold from the outside, leaving the inside clear for tack welds.
FAQ for welders
Which holds the most?
The MagTab Jumbo, up to 80 lb on 0.08 in flat steel. The YESWELDER arrow magnets follow at up to 44 lb, and the Grasshopper holds 35 lb.
Which has an on and off switch?
The YESWELDER switchable arrow magnets. The switch lets you activate or release the magnetic field, so the magnets are easy to attach, remove and reposition.
Which is best for corners?
The 90-degree neodymium magnets, holding from the outside for clear inside tack welds. Their different outer edges also set materials at 30 and 60 degrees.
Which magnets hold round surfaces?
The MagTab Jumbo and the Grasshopper, both with adjustable V-pad bases that adapt to round, flat and angled surfaces. The Grasshopper base also adapts to square surfaces.
Scoring, line by line
The Weld Score weighs holding fit, build and value, scored on performance, build, value, safety and warranty. The MagTab Jumbo leads on its 80 lb pull and adjustable V-pad base, the YESWELDER follows on its switch and 45, 90 and 135 degree positions, the Grasshopper follows on its spring-loaded arm and brass tip, and the 90-degree neodymium magnets follow on their outside corner hold. No listing here states a safety certification or a warranty term, so safety and warranty score zero across the board.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| MagTab Jumbo | 9.7 | 33 | 21 | 20 | n/a | 0 |
| YESWELDER Arrow | 9.6 | 32 | 21 | 20 | n/a | 0 |
| Grasshopper | 9.6 | 32 | 20 | 20 | n/a | 0 |
| 90 Degree Neodymium | 9.6 | 30 | 20 | 20 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.
More welding guides
Also see our welding magnets vs welding clamps comparison and welding magnets for squaring.
More guides: best welding magnets for auto body.




