Best Sheet Metal Screws #10 (2026)
Five #10 sheet metal screws, from 1/2 inch to 1 inch, compared on head style, stainless grade, drive and pack size, with the stated warranty in the mix.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallBNUOK #10 x 3/4 in Pan Head9.7/10View on Amazon - 2
Best Self-DrillingBNUOK #10 x 3/4 in Self-Drilling Hex Washer9.6/10View on Amazon - 3
Largest PackWensilon #10 x 1 in Truss Head9.6/10View on Amazon - 4
Best Short Pan HeadRoyceMart #10 x 1/2 in Pan Head9.6/10View on Amazon
A sheet metal screw holds a patch panel, a duct seam or a bracket to thin steel, and the wrong one strips out or snaps before it bites. This guide compares the best sheet metal screws #10 for shop and home work, on head style, length, stainless grade and drive, so the screw you pick matches the metal and the job.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall BNUOK #10 x 3/4 in Pan Head: 304 stainless steel, stated thread pitch and head diameter, 100 pieces and the only stated warranty here, 24 months. Check price on Amazon
- Best Self-Drilling BNUOK #10 x 3/4 in Self-Drilling Hex Washer: Self-drilling tip for use without pre-drilling, hex washer head and a 5/16 inch socket bit adapter in the box. Check price on Amazon
- Largest Pack Wensilon #10 x 1 in Truss Head: 200 pieces of #10 x 1 inch truss head screws in 410 stainless steel, the longest screw here. Check price on Amazon
- Best Short Pan Head RoyceMart #10 x 1/2 in Pan Head: A #10 x 1/2 inch Phillips pan head screw in 304 stainless steel with stated head diameter, head height and thread pitch. Check price on Amazon
The machines

BNUOK #10 x 3/4 Inch Pan Head Wood Screws
A 100 pack of #10 x 3/4 inch Phillips pan head screws in 304 stainless steel, with a stated thread pitch, head diameter and a 24-month warranty.
Pros
- 304 stainless steel (18-8) with stated corrosion and rust resistance
- States thread pitch 0.063 in, thread length 3/4 in and head diameter 0.363 in
- Deep cut Phillips drive for a snug fit in the screw head
- 24-month warranty stated in the listing
Cons
- 3/4 inch length suits thin stock; thicker stock needs a longer screw
- Pan head sits above the surface, not flush
- No washer head, so a separate washer is needed where a wide bearing surface matters
- 100 pieces only; a big job needs more than one box

BNUOK #10 x 3/4 Inch Self Drilling Screws, (58pcs)
A 58 piece box of #10 x 3/4 inch self-drilling screws in 410 stainless steel with a black zinc finish, a hex washer head and a 5/16 inch socket bit adapter in the box.
Pros
- Self-drilling tip, stated for use without pre-drilling
- Hex washer head holds a snug fit without extra washers
- 5/16 inch socket bit adapter included in the box
- 410 stainless steel with black zinc plating, stated corrosion and rust resistant
Cons
- 58 pieces per box, the smallest pack here
- One length only, 3/4 inch
- No warranty term stated in the listing
- Hex washer head stands above the surface, so it does not sit flush

(200 pcs) Wensilon #10×1”for Sheet Metal
A 200 piece pack of #10 x 1 inch truss head self-tapping screws in 410 stainless steel, with deep threads and an extra cross-drilled tail in each box.
Pros
- 200 pieces, the largest pack here
- 1 inch length, the longest here
- 410 stainless steel truss head with a deep thread design
- Extra cross-drilled tail included in each box
Cons
- No warranty term stated in the listing
- Truss head is wide and low, so it does not sit flush
- One length only, 1 inch
- 200 pieces suits a big job; a small job leaves most of the box unused

#10 x 1/2" (100 Pack) Stainless Steel Phillips Pan
A 100 pack of #10 x 1/2 inch Phillips pan head screws in 304 stainless steel, with stated head diameter, head height and thread pitch.
Pros
- 304 stainless steel (18-8) with stated heat and corrosion resistance
- States head diameter 9.5 mm, head height 3.55 mm and thread pitch 1.6 mm
- Sharp pointed thread design cuts into thin metal, plastic and wood
- Pan head gives a smooth, low-profile finish
Cons
- 1/2 inch length, the smallest length here
- Pan head sits above the surface, not flush
- No washer head for a wide bearing surface
- 100 pieces; a big job needs more than one box

MewuDecor #10 x 1/2" Pan Head Self Tapping Screws
A 100 pack of #10 x 1/2 inch black oxide pan head self-tapping screws in 304 stainless steel for wood and sheet metal.
Pros
- 304 stainless steel (18-8) with a black oxide finish
- 100 pieces of #10 x 1/2 inch pan head screws
- Self-tapping point for sheet metal and wood
- Inch measurement system, so sizes match US hardware
Cons
- Short 1/2 inch length suits thin stock only
- Pan head sits above the surface, not flush
- No washer head for a wide bearing surface
- 100 pieces; a big job needs more than one box
Spec sheet comparison
| Model | Gear Score | Size | Head | Material | Pack | Drive | Warranty |
|---|---|---|---|---|---|---|---|
| BNUOK #10 x 3/4 in Pan Head | 9.7/10 | #10 x 3/4 in | Phillips pan head | 304 stainless | 100 pcs | Phillips | 24 months |
| BNUOK #10 x 3/4 in Self-Drilling Hex Washer | 9.6/10 | #10 x 3/4 in | Hex washer head | 410 stainless | 58 pcs | Hex, 5/16 in socket | Not stated |
| Wensilon #10 x 1 in Truss Head | 9.6/10 | #10 x 1 in | Truss head | 410 stainless | 200 pcs | Not stated | Not stated |
| RoyceMart #10 x 1/2 in Pan Head | 9.6/10 | #10 x 1/2 in | Phillips pan head | 304 stainless | 100 pcs | Phillips #2 | Not stated |
| MewuDecor #10 x 1/2 in Pan Head | 9.5/10 | #10 x 1/2 in | Pan head | 304 stainless | 100 pcs | Not stated | Not stated |
Specifications are manufacturer rated, as published by each maker and collected 22 November 2026.
How to pick the best sheet metal screws #10
Length and thread
Length decides how much thread bites into the metal behind the sheet. The screws here run from 1/2 inch to 1 inch long, with the 1/2 inch screws suited to thin sheet and the 1 inch Wensilon giving the most length here. Thread pitch is stated on two picks: 0.063 inch on the BNUOK pan head screw and 1.6 mm on the RoyceMart. A sharp point starts the screw fast, and a self-tapping thread cuts its own path.
Head style and drive
Head style decides how the screw sits and what it holds down. Pan heads sit above the surface with a smooth, low-profile finish, and three picks here use them. The truss head on the Wensilon is a wide, low head, while the hex washer head on the BNUOK self-drilling screw holds a snug fit without extra washers. Two pan head screws state a Phillips drive, with a #2 bit stated on the RoyceMart, and the self-drilling screw uses a hex drive with a 5/16 inch socket bit adapter in the box. Match the bit to the drive before you start.
Stainless grade and finish
Stainless grade decides how the screw stands up to rust. Three picks here state 304 stainless steel (18-8): the BNUOK and RoyceMart pan head screws and the black oxide MewuDecor. Two picks state 410 stainless steel: the Wensilon truss head and the BNUOK self-drilling screw, which adds black zinc plating. The BNUOK and RoyceMart state corrosion and rust resistance, and the self-drilling screw states excellent corrosion and rust resistance. The black finishes give a dark look against the silver finish of the other picks.
Pilot holes and self-drilling tips
A self-tapping screw cuts its own thread, and a self-drilling screw cuts its own hole too. The BNUOK self-drilling screw states it can be used without pre-drilling, for metal-to-metal or metal-to-wood connections. The Wensilon states no installation holes for non-metallic or soft metal, screwed directly into the product. The BNUOK and RoyceMart state a sharp point for fast starts, but no pilot hole size is stated, so drill one when the metal is thick or the screw binds.
Pack size
Pack size decides how many jobs one box covers. The Wensilon box holds 200 pieces, the largest pack here, while the BNUOK and RoyceMart pan head screws and the MewuDecor each hold 100 pieces. The self-drilling box holds about 58 pieces and weighs 0.5 lb per the box. Match the pack to the job: a fence or a trailer floor eats screws fast, while one bracket needs only a few.
Use as directed. Wear eye protection when drilling and driving screws, clamp the work before you drill, and keep hands clear of the bit. Check the screw length against the metal thickness so the point does not punch through where it should not. See the Safety Disclaimer.
Before You Strike an Arc
- Match the bit to the drive: Phillips for the BNUOK and RoyceMart pan head screws, a 5/16 inch socket for the self-drilling screw, and check the drive on the Wensilon and MewuDecor on arrival.
- Check the screw length against the metal: 1/2 inch, 3/4 inch or 1 inch, so the thread bites without punching through.
- Check the head style against the bracket: pan head, truss head or hex washer head, so the head clears the work.
- Count the pack on arrival: 200, 100 or about 58 pieces, so a short box does not stall the job.
- Keep a spare bit on hand: only the self-drilling box includes a 5/16 inch socket bit adapter.
FAQ for welders
Do sheet metal screws always require a pilot hole?
No. The BNUOK self-drilling screw states it can be used without pre-drilling, and the Wensilon states no installation holes for non-metallic or soft metal. The pan head screws here are self-tapping, but no pilot hole size is stated, so drill one when the metal is thick or the screw binds.
How to remove rusted screws from metal?
The screws here are sold for fastening, and none of them states a removal method. The BNUOK and RoyceMart 304 stainless screws state corrosion and rust resistance, and the self-drilling screw states excellent corrosion and rust resistance. For a screw already rusted in place, back it out with the drive it went in with, Phillips or hex, and replace it with a stainless screw from this guide.
How to screw through metal?
Use a self-drilling screw where one is stated, like the BNUOK self-drilling screw with its drill tip and 5/16 inch socket bit adapter. For the self-tapping screws here, the thread cuts its own path in thin metal. Hold the screw straight, drive it with the matching bit, and stop when the head seats.
Can you screw into metal?
Yes. The screws here are stated for sheet metal, thin metal, steel studs and aluminum. The BNUOK self-drilling screw is stated for metal-to-metal or metal-to-wood connections, and the Wensilon is stated for soft metal with no installation holes.
How to remove sheet metal screws?
Back the screw out with the drive it went in with. The BNUOK and RoyceMart pan head screws use a Phillips drive, with a #2 bit stated on the RoyceMart, and the self-drilling screw uses a hex drive with a 5/16 inch socket bit adapter in the box. Turn the screw out slowly so the thread does not strip, and keep the bit seated in the head.
Related: best sheet metal screws, best sheet metal screw assortment kit, best sheet metal tools, best penetrating oil for rusted screws, how to remove broken screw from metal, and the sheet metal and tubing hub.
Scoring, line by line
Each screw is scored out of 10 on performance, build, value, safety listing and warranty, with the weights on the How We Pick page. Screws carry no electrical safety listing, so every screw here scores zero on safety, and the ranking comes from the other four. Only one screw here carries a stated warranty term.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| BNUOK #10 x 3/4 in Pan Head | 9.7 | 30 | 21 | 21 | n/a | 4 |
| BNUOK #10 x 3/4 in Self-Drilling Hex Washer | 9.6 | 29 | 21 | 20 | n/a | 0 |
| Wensilon #10 x 1 in Truss Head | 9.6 | 28 | 20 | 21 | n/a | 0 |
| RoyceMart #10 x 1/2 in Pan Head | 9.6 | 28 | 20 | 20 | n/a | 0 |
| MewuDecor #10 x 1/2 in Pan Head | 9.5 | 26 | 19 | 20 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




