Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Screws for Knife Handles (2026): 4 Picks for Fixed-Blade and Folding Knives

M4 and M2.5 knife handle screw sets for fixed-blade, kitchen, hunting and folding knives, compared on thread, hole size, length, material and pack count.

Best Screws for Knife Handles (2026): 4 Picks for Fixed-Blade and Folding Knives
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1KODRANEX M4 10 PackBest OverallKODRANEX M4 10 Pack9.7/10View on Amazon
  2. 2YUEARN M4 Gold 12 PackLongest FitYUEARN M4 Gold 12 Pack9.7/10View on Amazon
  3. 3Waziaqoc M4 10 PackStainless PickWaziaqoc M4 10 Pack9.6/10View on Amazon
  4. 4HanTof M2.5 100 PackLargest PackHanTof M2.5 100 Pack9.6/10View on Amazon

A handle that wobbles makes a knife useless on the bench, no matter how sharp the edge. The fix is a fastener made for the job: a screw set sized for the hole in the scales, with caps that sit flush and a thread that holds through daily cutting. This guide covers the best screws for knife handles, comparing screw sets for fixed-blade, kitchen, hunting and folding knives on thread, hole fit, length, material and pack count.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall KODRANEX M4 10 Pack: M4 thread for 5mm holes, 17.2mm overall, removable caps, and DIN912 alloy steel at 39 to 44 HRC. Check price on Amazon
  • Longest Fit YUEARN M4 Gold 12 Pack: 30.2mm overall for 6mm holes, M4 thread, and a small wrench included in the pack. Check price on Amazon
  • Stainless Pick Waziaqoc M4 10 Pack: Stainless steel M4 fasteners in a 10 pack, with a hex flat head for easy tightening. Check price on Amazon
  • Largest Pack HanTof M2.5 100 Pack: 100 pieces in 4 sizes, M2.5, 304 stainless steel, with a torx screwdriver for T6 and T8. Check price on Amazon

The machines

KODRANEX 10 Pack Knife Handle Screws Rivets Bolts

KODRANEX 10 Pack Knife Handle Screws Rivets Bolts

KODRANEX9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An M4 screw set for 5mm holes with a 17.2mm overall length, removable flat-head caps and DIN912 alloy steel hardened to 39 to 44 HRC.

Pros

  • M4 coarse thread with 0.7mm pitch for a standard 5mm drilled hole
  • Removable caps let scales come off for cleaning or a swap, with no rivets to drill out
  • DIN912 alloy steel hardened to 39 to 44 HRC
  • Fixed 17.2mm overall length with 7.8mm caps that finish flush on both faces

Cons

  • Fixed length fits one handle thickness, so measure before ordering
  • A 2.5mm hex key is needed to install and is not included
  • No warranty term is stated
  • Black is the only finish
12 Packs Knife Handle Screws Rivets Bolts

12 Packs Knife Handle Screws Rivets Bolts

YUEARN9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A gold M4 set for 6mm holes with a 30.2mm overall length, a 25mm screw length and a small wrench in the pack.

Pros

  • 30.2mm overall length fits thicker handles than the other M4 sets here
  • Fits 6mm handle holes with an M4 thread
  • DIN912 alloy steel with heat treatment hardness of 39 to 44 HRC
  • A small wrench comes in the pack

Cons

  • Gold is the only finish
  • 30.2mm length may be too long for thin handles
  • No warranty term is stated
  • 12 pieces cover fewer handles than the 100 piece set here
Waziaqoc Knife Handle Screws Rivets, Black

Waziaqoc Knife Handle Screws Rivets, Black

Waziaqoc9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A black stainless steel M4 set in a 10 pack, sized 0.7 by 0.3 inches with a hex flat head for blade fixing and DIY knife work.

Pros

  • Stainless steel with resistance to rust, corrosion and daily wear
  • Hex flat head tightens with common tools
  • Fits chef knives, hunting blades and pocket knives
  • 10 pack covers several handles or spares

Cons

  • Black is the only finish
  • A pilot hole must be drilled before the screw goes in
  • 10 pieces cover fewer handles than the larger packs here
  • Sized for standard handles, so thick scales may need a longer fastener
HanTof 100pcs Pocket blade knife handle

HanTof 100pcs Pocket blade knife handle

HanTof9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 100 piece M2.5 set in 304 stainless steel across 4 sizes, with a torx screwdriver for T6 and T8, made for pocket and folding knives.

Pros

  • 100 pieces across 4 sizes, with 25 of each size
  • 304 stainless steel, stated as durable and antirust
  • Torx screwdriver for T6 and T8 comes in the pack
  • Covers pocket blades, folding knives, clips and pivot pins

Cons

  • M2.5 size suits pocket and folding knives, not the fixed-blade handles the M4 sets cover
  • Each of the 4 sizes must be measured against the knife before use
  • Small M2.5 screws need a steady hand and the right torx driver
  • 100 small pieces are easy to lose in the shop

Spec sheet comparison

Model Gear Score Thread Hole size Overall length Pack count Material Warranty
KODRANEX M4 10 Pack 9.7/10 M4 5mm 17.2mm 10 DIN912 alloy steel None stated
YUEARN M4 Gold 12 Pack 9.7/10 M4 6mm 30.2mm 12 DIN912 alloy steel None stated
Waziaqoc M4 10 Pack 9.6/10 M4 Not stated 0.7 x 0.3 in 10 Stainless steel None stated
HanTof M2.5 100 Pack 9.6/10 M2.5 Not stated Not stated 100 304 stainless steel None stated

Specifications are manufacturer rated, as published by each maker and collected 21 November 2026.

Buying guide: what matters in the best screws for knife handles

Handle screws look simple, and the wrong size still ruins a fit. Thread, hole size and length decide whether a set works, while material and pack count decide how long it lasts and how many handles it covers.

Thread and hole size

M4 is the common thread here. The KODRANEX set runs an M4 coarse thread at 0.7mm pitch for a standard 5mm drilled hole, while the YUEARN set runs M4 for 6mm holes. The HanTof set runs M2.5 for pocket and folding knives. Measure the hole before ordering, since a screw that is too big will not seat and one that is too small will wobble.

Length and handle thickness

Length must match the handle. The KODRANEX fastener runs a fixed 17.2mm overall, with a 12mm center shaft and a 2.6mm thick cap on each end, finishing flush at 7.8mm on both faces. The YUEARN fastener runs 30.2mm overall, with a 25mm screw length and a 6mm screw diameter, for thicker handles. The Waziaqoc screw measures 0.7 by 0.3 inches, about 17.8mm by 7.6mm. Check the length against the handle thickness before ordering, since a fixed length fits one thickness.

Material and hardness

KODRANEX and YUEARN state DIN912 alloy steel hardened to 39 to 44 HRC. The HanTof set states 304 stainless steel, and the Waziaqoc set states stainless steel. Hardness matters where the handle sees heavy daily cutting and outdoor carry, while stainless suits damp kitchens and pockets.

Pack count and spares

Pack counts here run from 10 to 100 pieces. The HanTof pack holds 100 pieces in 4 sizes, with 25 of each size. The YUEARN pack holds 12 shafts and 24 flat head screws. The KODRANEX pack holds 10 complete fasteners, with 10 shafts and 20 caps. The Waziaqoc pack holds 10 screws. A larger pack suits a maker with many handles to fit, while a 10 pack suits a re-handle.

Removable screws or rivets

Screws beat rivets where the scales may come off again. The KODRANEX caps loosen any time, so scales can be swapped, cleaned under the handle, or replaced on an old knife. Rivets, once hammered, cannot be undone without drilling. Where a handle will never come apart, a rivet still works, but these screw sets give the maker a way back in.

Use as directed. Clamp the scales and the blade before drilling, wear eye protection, and keep fingers clear of the edge while fitting screws. Drill a pilot hole where the maker calls for one, and never force a screw into a hole that is too small.

Before You Strike an Arc

  • Confirm the hole size first: 5mm for the KODRANEX set and 6mm for the YUEARN set.
  • Match the overall length to the handle: 17.2mm on the KODRANEX set and 30.2mm on the YUEARN set.
  • Have a 2.5mm hex key ready for the KODRANEX set, since none is included; the YUEARN set includes a small wrench, and the HanTof set includes a torx screwdriver for T6 and T8.
  • Check that the caps sit flush on both faces of the handle before the knife goes back to work.
  • Measure each size in the HanTof 100 piece pack against the knife before fitting, since the pack holds 4 sizes.

FAQ for welders

What are knife handle screws called?

They go by handle screws, fasteners, bolts and rivets, and the makers here use each of those words. The sets in this guide are screw fasteners with a center shaft and a cap on each end, not solid rivets. The name on the box matters less than the thread, the hole size and the length.

What size hole do knife handle screws need?

It depends on the set. The KODRANEX M4 set needs a standard 5mm drilled hole, and the YUEARN M4 set fits 6mm handle holes. Measure the hole in the scales before ordering, and match the screw to the hole, not the other way around.

What thread size fits a knife handle?

M4 is the common thread in this guide, used by the KODRANEX, YUEARN and Waziaqoc sets. The HanTof set uses M2.5, a smaller thread for pocket and folding knives. The thread must match the hole and the caps, so check the thread before buying.

How do you fit knife handle screws?

Push the shaft through the hole in the scales and tighten a cap on each end. The KODRANEX set tightens with a 2.5mm hex key, which is not included, while the YUEARN set includes a small wrench. Drill a pilot hole first where the maker calls for one, and check that the caps finish flush on both faces.

Can you remove knife handle screws later?

Yes. Unlike hammered solid rivets, which cannot be undone, the KODRANEX caps loosen any time, so scales can be swapped, cleaned under the handle, or replaced on an old knife. That makes screw fasteners the better pick where a handle may come apart again.

Related: best knife handle fasteners, best stabilized wood knife scales, best wood for knife handles, best knife blanks full tang, and the knife making hub. Also see knife making parts and the knife handle screws hub.

Scoring, line by line

Each screw set is scored on performance, build, value, safety listing and warranty, with the weights published on the method page. Knife handle screws carry no electrical safety listing, so each set here scores zero on that criterion; the ranking comes from the other criteria.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
KODRANEX M4 10 Pack 9.7 32 22 21 n/a 0
YUEARN M4 Gold 12 Pack 9.7 30 22 21 n/a 0
Waziaqoc M4 10 Pack 9.6 28 20 21 n/a 0
HanTof M2.5 100 Pack 9.6 27 19 22 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

More buying guides