Best Knife Handle Fasteners (2026): 5 Sets Compared
Five knife handle fastener sets compared by thread size, screw length, material, hardness and pack count, for handles that stay tight.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallCkyleole Cutlery Rivets 12 Sets9.7/10View on Amazon - 2
Best Screw SetYUEARN Knife Handle Screws9.6/10View on Amazon - 3
Best Adjustable LengthEllaYIDOI Knife Handle Screws9.6/10View on Amazon - 4
Best Black ScrewsSliverdew Knife Handle Screws9.6/10View on Amazon - 5
Most SetsNufiwra Bracket Bolt Fasteners9.6/10View on Amazon
A loose knife handle turns a good blade into a wobbling chore, and the best knife handle fasteners are the ones that match the hole, the handle thickness and the look of the knife. This guide compares fastener sets on what each listing states: thread and rod size, screw length, material, hardness and pack count.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Ckyleole Cutlery Rivets 12 Sets: Brass and stainless rivets with a 0.276 inch head and 0.63 inch shaft Check price on Amazon
- Best Screw Set YUEARN Knife Handle Screws: 12 M4 shafts, 24 flat head screws and a small wrench included Check price on Amazon
- Best Adjustable Length EllaYIDOI Knife Handle Screws: Screw length adjusts from 17.2 to 22 mm with a 2 mm hex nut Check price on Amazon
- Best Black Screws Sliverdew Knife Handle Screws: 10 M4 shafts and 20 flat head screws in black alloy steel Check price on Amazon
- Most Sets Nufiwra Bracket Bolt Fasteners: 16 sets in brass and stainless steel with a 6 mm head Check price on Amazon
The machines

12 Sets Cutlery Rivets 5/16 x 5/8 inch Cutlers
A 12-set pack of brass and stainless steel cutlery rivets with a 0.276 inch head and a 0.63 inch shaft for knife handles.
Pros
- Brass and stainless steel with corrosion resistance stated
- 0.276 inch head and 0.63 inch shaft for a snug fit
- Two-part compression design bonds under pressure
- Polished finish adds a protective layer against oxidation
Cons
- Hammer install needs a steady tap and a file for excess
- No screwdriver install option is stated
- 12 sets cover fewer handles than the 16-set Nufiwra pack
- No warranty term is stated

12 Packs Knife Handle Screws Rivets Bolts
A 12-pack of gold M4 knife handle screws with a 5 mm diameter, 17.2 mm total length and a small wrench included.
Pros
- DIN912 alloy steel with 39-44HRC hardness stated
- Small wrench included as a gift
- 12 shafts and 24 flat head screws in the pack
- Gold finish for a bright handle look
Cons
- Fixed 12 mm screw length with no adjustment stated
- Fits 5 mm handle holes only
- Gold color may not suit every handle
- 12 packs hold fewer sets than the 16-set Nufiwra pack

10 Packs Knife Handle Screws Rivets Bolts
A 10-pack of black M4 knife handle screws with an adjustable 17.2 to 22 mm length and DIN 912 alloy steel.
Pros
- DIN 912 alloy steel with HRC 39-44 hardness stated
- Screw length adjusts from 17.2 to 22 mm
- 7.8 mm nut with 2 mm hex for a snug fit
- 10 shafts and 20 flat head screws in the pack
Cons
- Black color only
- No wrench is included
- 10 packs hold fewer sets than the 16-set Nufiwra pack
- Screws only, with no rivet option for a hammered joint

10 Pack Knife Handle Screws Hex Flat Head Knife
A 10-pack of black M4 knife handle screws with a 5 mm connecting rod and an adjustable 17.2 to 22 mm screw length.
Pros
- 5 mm connecting rod with 12 mm length for a precise fit
- Screw length adjusts from 17.2 to 22 mm
- 7.8 mm nut with 2 mm hex sizing
- 10 M4 shafts and 20 flat head screws in the pack
Cons
- No DIN grade or hardness figure is stated
- Black color only
- No wrench is included
- 10 packs hold fewer sets than the 16-set Nufiwra pack

16 Sets Brass Bracket Bolt Fasteners and Stainless
A 16-set pack of brass and stainless steel bracket bolt fasteners with a 6 mm head for knife handles.
Pros
- 16 sets, the largest pack here
- Brass and stainless steel sets in one pack
- 6 mm head diameter for a bold pin look
- Screw and stud in each set for a complete joint
Cons
- Fastener length is stated as approximately 25 mm
- No thread size is stated
- Grinding is needed to finish protruding pins
- No warranty term is stated
Spec sheet comparison
| Fastener | Gear Score | Size | Length | Material | Pack |
|---|---|---|---|---|---|
| Ckyleole Cutlery Rivets 12 Sets | 9.7/10 | 5/16 x 5/8 in | 0.63 in shaft | Brass, stainless | 12 sets |
| YUEARN Knife Handle Screws | 9.6/10 | M4, 5 mm | 17.2 mm total | DIN912 alloy steel | 12 packs |
| EllaYIDOI Knife Handle Screws | 9.6/10 | M4, 5 mm | 17.2-22 mm | DIN 912 alloy steel | 10 packs |
| Sliverdew Knife Handle Screws | 9.6/10 | M4, 5 mm | 17.2-22 mm | Alloy steel | 10 pack |
| Nufiwra Bracket Bolt Fasteners | 9.6/10 | 4 mm shaft | 25 mm | Brass, stainless | 16 sets |
Ratings in this table are the makers’ own claims taken from each product page (21 November 2026).
How to choose the best knife handle fasteners
Screw size and hole size
The M4 screw sets fit 5 mm handle holes: the EllaYIDOI, YUEARN and Sliverdew screws all use an M4 thread with a 5 mm rod or screw diameter. The Ckyleole rivets are a different fit at 5/16 by 5/8 inch, with a 0.276 inch head and a 0.63 inch shaft. The Nufiwra fasteners have a rivet shaft outer diameter of about 4 mm. Measure the drilled hole before ordering, since an M4 screw will not fill a rivet hole and a rivet will not thread into a tapped hole. See the knife making parts guide for the rest of the build.
Screw length against handle thickness
Length decides whether the fastener sits flush or stands proud. The EllaYIDOI and Sliverdew screws adjust from 17.2 to 22 mm, so one set covers thin and thick handles. The YUEARN screws have a fixed total length of 17.2 mm with a 12 mm screw length, which suits thinner handles. The Nufiwra fasteners run about 25 mm long, the longest figure here, and the Ckyleole rivet shaft runs 0.63 inch. Match the length to the handle thickness plus the blade tang, and grind the excess flush where the listing says to.
Rivets or screws
Screws and rivets install differently. The M4 screw sets install by drilling, adjusting and tightening with a screwdriver, and the YUEARN pack even includes a small wrench. The Ckyleole rivets install by drilling a hole, placing the rivet and tapping it with a hammer, then polishing or filing the excess down. The Nufiwra sets install the same way, with grinding to finish protruding pins. Screws come apart for a handle swap, while rivets form a permanent joint. See blind rivets vs solid rivets for the joint types.
Material and finish
Material decides rust resistance and looks. The EllaYIDOI and YUEARN screws use DIN 912 alloy steel, with hardness stated at HRC 39 to 44, while the Sliverdew screws use high-hardness alloy steel with no grade stated. The Ckyleole rivets and the Nufiwra sets mix brass and stainless steel, both stated rust-proof and corrosion-proof. Finishes run from gold on the YUEARN screws to black on the EllaYIDOI and Sliverdew screws and Silver and Gold on the Ckyleole rivets. Pick the metal that matches the handle wood and the blade. See the best wood for knife handles guide for handle material.
Before You Strike an Arc
- Check the hole size first: the M4 screws here fit 5 mm handle holes.
- Match screw length to handle thickness: the adjustable screws run 17.2 to 22 mm, while the YUEARN screw is 12 mm long.
- Keep the 2 mm hex driver and the YUEARN wrench with the kit.
- Grind or polish rivet ends flush after the hammer tap on the Ckyleole and Nufiwra sets.
FAQ for welders
How are knife handles attached?
With screws or rivets. The M4 screw sets install by drilling, adjusting and tightening with a screwdriver, while the Ckyleole rivets install by drilling a hole, placing the rivet and tapping it with a hammer, then polishing or filing the excess.
What size hole do these fasteners need?
The M4 screw sets fit 5 mm handle holes. The Ckyleole rivets are 5/16 by 5/8 inch, and the Nufiwra fasteners have a rivet shaft outer diameter of about 4 mm.
What screw lengths do these sets offer?
The EllaYIDOI and Sliverdew screws adjust from 17.2 to 22 mm. The YUEARN screws have a total length of 17.2 mm with a 12 mm screw length, and the Nufiwra fasteners run about 25 mm long.
Which fasteners come in brass?
The Ckyleole rivets combine brass and stainless steel, and the Nufiwra pack holds 8 brass sets and 8 stainless steel sets. The YUEARN screws are gold, and the EllaYIDOI and Sliverdew screws are black.
How many fasteners come in each pack?
The Nufiwra pack holds 16 sets and the Ckyleole pack holds 12 sets. The YUEARN pack holds 12 screw shafts and 24 flat head screws, and the EllaYIDOI and Sliverdew packs each hold 10 shafts and 20 flat head screws.
Related: knife casting hub, knife making hub, best wood for knife handles, best knife handle spacer material and best stabilized wood knife scales.
Scoring, line by line
Each fastener is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. No fastener here states a safety listing or a warranty term, so safety and warranty add nothing to any score here; the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Ckyleole Cutlery Rivets 12 Sets | 9.7 | 32 | 22 | 21 | n/a | 0 |
| YUEARN Knife Handle Screws | 9.6 | 30 | 21 | 21 | n/a | 0 |
| EllaYIDOI Knife Handle Screws | 9.6 | 30 | 21 | 20 | n/a | 0 |
| Sliverdew Knife Handle Screws | 9.6 | 29 | 20 | 20 | n/a | 0 |
| Nufiwra Bracket Bolt Fasteners | 9.6 | 28 | 20 | 20 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




