Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Welding Helmet Shade Chart: Lens Shade by Process

A welding helmet shade chart matches lens shade to the welding process and the brightness of the arc, so the shade follows the work and the puddle stays clear.

Welding Helmet Shade Chart: Lens Shade by Process
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YESWELDER Auto Darkening Welding HelmetYESWELDER Auto Darkening Welding Helmet9.5/10View on Amazon
  2. 2YESWELDER Auto Darkening Welding HelmetYESWELDER Auto Darkening Welding Helmet9.5/10View on Amazon
  3. 3TOOLIOM Flip-Up 5 x 4.3" Lens Welding Helmet for MIGTOOLIOM Flip-Up 5 x 4.3" Lens Welding Helmet for MIG9.4/10View on Amazon

Strike an arc on a piece of scrap and the helmet lens has to cut the glare and leave the puddle clear enough to read. A welding helmet shade chart answers that balance. It matches the lens shade to the welding process and the brightness of the arc, so the shade follows the work instead of guesswork.

This guide links to product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same.

How to Read a Welding Helmet Shade Chart

Read the chart by process, then by arc brightness. Find the row for the process on the bench, stick, MIG, TIG or plasma cutting, then follow that row across to the shade that matches the arc. A brighter arc needs a darker shade, and a low, steady arc needs a lighter shade. When the process changes, check the chart again instead of leaving the shade where it was.

What the Shade Number Means

The shade number rates how dark the lens gets when the arc strikes. A higher shade number means a darker lens and less light reaching the eyes. On an auto-darkening helmet, the lens stays light while the welder sets up, then darkens to the set shade the moment the arc strikes. On a fixed shade lens, the shade stays put, so the lens must match the process before the arc starts.

Shade by Process

Process Arc light Shade direction What to watch
Stick Stick welding Bright arc, heavy spatter Darker shade for a brighter arc Keep spatter off the lens
MIG MIG welding Bright, steady arc Darker shade as the arc grows brighter Watch the puddle at the toe of the weld
TIG TIG welding Clean, focused arc Lighter shade for a low, steady arc A clear view helps on thin metal
Plasma cutting Plasma cutting Very bright cutting arc Darker shade for the cutting arc Keep the lens clean and the cut steady

Stick and MIG run bright arcs, so the chart points those rows toward darker shades as the arc grows brighter. TIG runs a clean, focused arc, so its row points toward a lighter shade on a low, steady arc. Plasma cutting throws a very bright arc, so it sits with the darker shades. Use the table as a starting point, then adjust by how the puddle reads through the lens.

Fixed Shade or Variable Shade

A fixed shade lens holds the same shade for every weld, which suits steady work on a process that stays put. A variable shade auto-darkening helmet lets the welder dial the shade up or down for the arc on the bench, which suits a shop that moves between processes. The variable shade lens still darkens on its own when the arc strikes, so the eyes stay covered during the switch from setup to weld. See the comparison of variable shade vs fixed shade welding lens and passive vs auto darkening welding helmet for the trade-offs.

When the Shade Feels Wrong

If the arc glares and the puddle washes out, the shade sits too light for the arc, so step it darker and check the chart again. If the joint stays hidden and the puddle reads as a black smear, the shade sits too dark, so step it lighter until the puddle and the joint edge show clear. A helmet left in grind mode stays light during a weld, so check the mode switch before blaming the shade. A dirty or pitted lens also dulls the view, so wipe the cover lens and swap it when the view stays hazy.

FAQ for welders

What shade should a beginner start with?

Start with the shade the chart shows for the process and the arc on the bench. If the arc glares, step the shade darker; if the joint stays hidden, step it lighter. A variable shade helmet makes those steps quick, since the shade dial sits on the helmet.

Why does the arc look too bright through the lens?

The shade sits too light for the arc, the helmet sits in grind mode, or the cover lens has gone hazy. Step the shade darker, check the mode switch, and wipe the cover lens. If the view stays bright after those checks, the lens may need a swap, so check the helmet manual.

Can the same helmet cover every process?

A variable shade auto-darkening helmet covers more processes than a fixed shade lens, since the shade adjusts to the arc on the bench. A fixed shade lens suits steady work on a process that stays put. For a shop that moves between stick, MIG and TIG, a variable shade helmet saves swapping lenses between jobs.

Does a darker shade protect the eyes better?

A darker shade cuts glare, but the lens blocks ultraviolet and infrared light in every state, light or dark. Pick the shade by how clearly the puddle shows, not by chasing the darkest lens. If the puddle reads clear and the arc shows without glare, the shade fits the work.

Related: welding helmets, best auto darkening welding helmet, best welding helmet for beginners, best lens for welding helmet, and welding helmet types.

More buying guides