Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Welding Hat Size Chart: How to Choose the Right Fit

A welding hat size chart turns a head measurement into the size to order, and this guide shows how to measure, read the chart, and pick a cap that fits under a helmet.

Welding Hat Size Chart: How to Choose the Right Fit
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ARCCAPTAIN Reversible FR Cotton Welding CapARCCAPTAIN Reversible FR Cotton Welding Cap9.6/10View on Amazon
  2. 2ARCCAPTAIN Reversible Welding CapARCCAPTAIN Reversible Welding Cap9.6/10View on Amazon
  3. 3Fullsheild Reversible Welding Cap Protective FRFullsheild Reversible Welding Cap Protective FR9.5/10View on Amazon

A cap that slides down over the eyes or rides up off the ears is a distraction under the hood, and it usually means the size is wrong rather than the cap. A welding hat size chart turns a head measurement into the size to order, so the cap sits flat under a helmet and stays put through a shift. Measure around the head, find the matching size on the maker’s chart, and order that size. This guide shows how to measure, how to read the chart, and which listed sizes the caps below come in.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

ARCCAPTAIN Reversible FR Cotton Welding Cap

ARCCAPTAIN Reversible FR Cotton Welding Cap

ARCCAPTAIN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8-panel reversible cap in 10 oz FR cotton with a heat-resistant lining and a sweatband, listed in 10 sizes from 6-7/8 to 8, so the size the chart points to is likely on the list.

Pros

  • Lists 10 sizes from 6-7/8 to 8, the most sizes stated here
  • 10 oz FR cotton with a heat-resistant cotton lining
  • Reversible, so it can be worn front or back
  • Sweat-absorbing cotton on the brim and bill

Cons

  • This listing covers one size, 7 3/8, so order the size the chart points to
  • Crown height is not stated, so coverage for long hair is unclear
  • Reversible design means both sides show wear
  • No stated weight
ARCCAPTAIN Reversible Welding Cap

ARCCAPTAIN Reversible Welding Cap

ARCCAPTAIN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A khaki 8-panel reversible cap in 260 grams of Martin Cloth with a 100% cotton lining, listed in 10 sizes from 6-7/8 to 8 for matching a head measurement to a size.

Pros

  • Lists 10 sizes from 6-7/8 to 8
  • 260 grams of Martin Cloth, nearly 2.5 times thicker than a regular welding beanie, per the maker
  • Reversible double-sided design for front or back wear
  • Sweat-absorbing cotton on the brim and bill

Cons

  • This listing covers one size, 7 3/8, so order the size the chart points to
  • No warranty term is stated
  • Crown height is not stated, so coverage for long hair is unclear
  • One cap per order, so there is no spare while one is in the wash
Fullsheild Reversible Welding Cap Protective FR

Fullsheild Reversible Welding Cap Protective FR

Fullsheild9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 100% cotton reversible cap with a deep crown stated at 7.9 inches tall, listed in 9 sizes, for welders who want ear coverage and room for long hair.

Pros

  • Deep crown stated at 7.9 inches tall, with ear protection and room for long hair
  • 9 sizes listed, so the fit is closer than one size fits all
  • 100% cotton, soft and breathable, with no shrinkage after washing, per the maker
  • Flame resistant, CAT 2 rating stated in the listing

Cons

  • This listing covers one size, 7 3/8, so order the size the chart points to
  • No warranty term is stated
  • No sweatband is stated, so sweat control rests on the cotton alone
  • No stated cloth weight, so the fabric weight is unclear

Welding Hat Size Chart: How to Read It

A welding hat size chart lists the sizes a maker sells and matches each one to a head measurement. Find the size on the chart that matches the measurement taken around the head, then order that listed size. The ARCCAPTAIN line lists 10 sizes from 6-7/8 to 8, and the Fullsheild line lists 9 sizes. Each listing below sells one size, 7 3/8, so the chart is what points to the size to order from the range.

Hat sizes use fractions, so read the chart from the measurement, not from a size worn in another brand. When the measurement lands on a line between listed sizes, check the size the maker lists for that measurement before ordering.

How to Measure for a Welding Hat

Use a soft tape, the kind used for sewing, and measure over the hair the way the cap will be worn. Wrap the tape around the head just above the eyebrows and ears, keeping it level all the way around. Pull it snug without pressing into the skin, and read where the tape meets the zero end. Repeat the measurement to confirm the reading, and use the reading that repeats.

Measure with the hair as it will sit under the cap, since a tight bun or a thick braid changes where the cap sits. Put the helmet on after the cap and check that the helmet still seats flat and the cap does not bunch at the brow.

What the Listed Sizes Mean

The size number is the hat size, and the chart ties it to a head measurement. A range such as 6-7/8 to 8 runs from the small end to the large end of the line. Order the exact size the chart points to, since a cap a size off may slide or pinch.

Crown depth matters as much as size. The Fullsheild cap states a deep crown at 7.9 inches tall, plus or minus 0.1 inch, which the maker says gives ear protection and room for long hair. The ARCCAPTAIN caps do not state a crown height, so their depth is not spelled out. A deep crown suits long hair and full ear coverage, per the maker’s description of the Fullsheild cap.

Side by Side

Cap Sizes listed Material Crown Gear Score
ARCCAPTAIN Reversible FR Cotton Cap 10 sizes, 6-7/8 to 8 10 oz FR cotton, 260 grams Martin Cloth Not stated 9.6/10
ARCCAPTAIN Reversible Welding Cap 10 sizes, 6-7/8 to 8 260 grams Martin Cloth, 100% cotton lining Not stated 9.6/10
Fullsheild Reversible Welding Cap 9 sizes 100% cotton 7.9 ± 0.1 in tall 9.5/10

All three caps are reversible, and all three list a stated size range rather than one size fits all. The two ARCCAPTAIN caps share the same cloth and size range, while the Fullsheild cap lists 9 sizes and adds a stated deep crown and a flame resistant CAT 2 rating. For more on caps in general, see our best welding caps guide and welding cap vs hard hat.

Welding Caps in Listed Sizes

Each cap below handles the step that comes after measuring: matching the measurement to a listed size and wearing the cap under a helmet.

FAQ for welders

What size welding hat do I need?

Measure around the head above the eyebrows and ears, then find the size the maker’s chart lists for that measurement. The ARCCAPTAIN line lists 10 sizes from 6-7/8 to 8, and the Fullsheild line lists 9 sizes. Order the listed size the chart points to, since each listing below sells one size, 7 3/8.

How do I measure my head for a welding cap?

Wrap a soft tape around the head just above the eyebrows and ears, keeping it level all the way around. Pull it snug without pressing into the skin, and read where the tape meets. Repeat the measurement to confirm the reading, and use the reading that repeats.

Should a welding cap fit tight or loose under a helmet?

It should sit flat and stay put without sliding down over the eyes or riding up off the ears. A cap that is too tight presses at the brow, while one that is too loose shifts under the helmet. The ARCCAPTAIN caps here use sweat-absorbing cotton on the brim and bill, which the maker says keeps sweat from reaching the eyes.

Can I wear a welding cap under a welding helmet?

Yes. The maker of the ARCCAPTAIN caps describes them as a liner for welding helmets, and the Fullsheild cap is described as a helmet liner as well. The cap should sit flat so the helmet still seats, and the reversible design lets the cap be worn front or back. For helmet fit in general, see our welding lens sizes guide.

What if my measurement falls between sizes on the chart?

Use the size the maker’s chart lists for the measurement, and order that size. If the chart is unclear, check the size range the maker lists before ordering rather than guessing from another brand. The ARCCAPTAIN line lists 10 sizes from 6-7/8 to 8, and the Fullsheild line lists 9 sizes, so use the chart for the cap being ordered.

Related: best welding caps, welding cap vs hard hat, welding safety gear checklist for beginners, and the welding safety gear hub. Also see our welding lens sizes guide.

More buying guides

Welding Safety Gear ·

Ear Plugs Size Chart for Shop Noise

An ear plugs size chart that maps XS, S, M and L tips and foam plugs to shop noise, with the stated SNR figures…