TIG Welding Machine for Beginners: What to Look For
A beginner TIG machine needs the right start, enough amps for the metal at hand, and the correct current type, and this guide shows what to check before buying.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ARCCAPTAIN 160A Stick WelderView on Amazon - 2
PLASMARGON 250A Stick WelderView on Amazon - 3
ARCCAPTAIN Stick WelderView on Amazon - 4
FEIFANKE 250A Stick Welder MachineView on Amazon - 5
AWT MIG Welding MachineView on Amazon - 6
VEVOR MIG Welder 200A Pluse Mig Welding Machine with LCDView on Amazon
A thin stainless patch on a cracked bracket, a small aluminum tab that needs a clean bead, a practice bead on scrap steel: that is the work a beginner TIG machine has to handle. A TIG welding machine for beginners is a small inverter welder that runs a tungsten electrode under argon, and this guide shows what to check in the amps, the start type, the current type and the power supply before buying.
Other welders and gear to compare
ARCCAPTAIN 160A Stick WelderCheck price on Amazon
PLASMARGON 250A Stick WelderCheck price on Amazon
ARCCAPTAIN Stick WelderCheck price on Amazon
FEIFANKE 250A Stick Welder MachineCheck price on Amazon
AWT MIG Welding MachineCheck price on Amazon
VEVOR MIG Welder 200A Pluse Mig Welding Machine with LCDCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
How to choose a TIG welding machine for beginners
Start with the metal. DC TIG welds steel and stainless, and AC TIG adds aluminum, so a beginner who only plans steel work can start with a DC machine, while anyone who wants aluminum needs AC/DC. The machines in this guide show the range: the ARCCAPTAIN ARC205P Pro lists up to 205A, the TOOLIOM TL-MCT520 lists TIG up to 200A, and the HAXIAOER HXT200P lists a 200A maximum. Check the start type next: high frequency start lights the arc without touching the metal, while lift start touches the tungsten to the work and lifts to start. Then check the power supply: dual voltage machines run on household and shop power, while a 220V only machine needs the higher voltage outlet. Pulse, a foot pedal and app control are useful extras, not requirements for a beginner machine. Our best entry level TIG welder guide rounds up machines for a beginner shop.
Side by side
| TOOLIOM TL-MCT520 | ARCCAPTAIN ARC205P Pro | HAXIAOER HXT200P | |
|---|---|---|---|
| Processes | MIG, TIG, plasma cut, stick, flux core | Pulse stick, stick, Lift TIG | AC/DC TIG, pulse TIG, stick, spot TIG |
| Max TIG output | 200A | 205A | 200A |
| Input voltage | 110/220V | 120V or 240V | 220V |
| TIG start | HF | Lift | HF |
| Pulse | Not stated | Yes | Yes |
| Aluminum TIG | Not stated | Not stated | Yes, AC TIG |
| Warranty | Not stated | 3 Years | Not stated |
The table uses the makers’ own figures. The ARCCAPTAIN lists the highest maximum at 205A, the HAXIAOER is the only one of the three that lists AC TIG for aluminum, and the TOOLIOM is the only one that also cuts and runs MIG. A beginner does not need every process; the table shows which machine covers which job. See our best multi-process welder with AC TIG guide for machines that do more than TIG alone.
DC or AC/DC: which one a beginner needs
DC TIG covers steel and stainless: brackets, patch panels, small frames and repair work. AC TIG adds aluminum, and the HAXIAOER lists AC TIG that welds aluminum from 0.5 to 5 mm and other metals from 0.5 to 10 mm. If aluminum is on the list, buy AC/DC; if it is not, a DC machine is the simpler place to learn and still handles the common steels. The ARCCAPTAIN is a stick welder with DC lift TIG for steel and stainless work, and its pulse mode cuts heat input on thin metal. Our AC TIG vs DC TIG guide compares the two currents in more detail.
Lift start or high frequency start
High frequency start lights the arc without touching the tungsten to the metal, which keeps the tungsten clean and the start consistent; the TOOLIOM and the HAXIAOER both list HF start. Lift start touches the tungsten to the work and lifts it to start the arc, which is the ARCCAPTAIN’s method, and it works fine on steel and stainless with a steady hand. Beginners usually find HF start easier, because there is no touch to get wrong, but either start will weld once the habit is set. Whichever start a machine lists, keep the tungsten sharp and the stickout short, and check the manual for the start the machine uses.
Power: household or shop supply
Dual voltage machines switch between household and shop power: the TOOLIOM runs on 110/220V, the Rotvik switches between 110V and 220V with a 20 to 200A output, and the ARCCAPTAIN runs 20 to 150A on 120V and 20 to 205A on 240V. A 220V only machine like the HAXIAOER needs the higher voltage outlet, so check the outlet before ordering. More amps on the higher voltage means thicker metal, but a beginner on thin metal will spend most time at the low end of the range, where control matters more than the maximum. Our best AC/DC TIG welder for home use guide covers machines that run on household power.
Safety: arc, fumes and gas
TIG makes a bright arc, hot metal and fumes, so treat it like any welding: a helmet with the right shade, gloves, long sleeves and boots, and ventilation that moves the plume away from the face. Galvanized steel gives off fumes that are harmful to breathe, so grind the coating off the weld area and the metal around it or weld it outdoors with the wind at the back, and never weld a sealed container or a tank that held fuel. Argon comes in a cylinder under pressure, so chain the cylinder upright, keep the regulator and hoses clear of the arc, and check the manual for the gas and the settings the machine calls for. See the OSHA welding overview and our Safety Disclaimer.
FAQ for welders
Can a beginner learn TIG on a DC-only machine?
Yes, for steel and stainless. DC TIG is the simpler place to start, and the ARCCAPTAIN shows the shape of it: lift start, a 20 to 150A range on 120V, and synergic control that matches the current to the electrode size. Aluminum needs AC, so a DC-only machine will not weld it; if aluminum is a goal, buy an AC/DC machine from the start.
Do I need a foot pedal to start TIG welding?
No. The machines here start at the torch: the TOOLIOM and the HAXIAOER use high frequency start, and the ARCCAPTAIN uses lift start. The TOOLIOM works with a foot pedal, and the pedal raises and lowers the current while welding, which helps on thin metal and at the end of a bead. A pedal is a useful extra, but lift or HF start will weld without one.
What gas does TIG welding need?
Argon, fed through the torch to shield the puddle from the air. The HAXIAOER comes with a gas regulator with a flowmeter, a gas hose and a TIG torch in the box, so the gas side is covered apart from the cylinder itself. Check the manual for the gas the machine calls for, and keep the cylinder chained upright.
Can one machine weld aluminum and steel?
Yes, with AC/DC TIG. The HAXIAOER lists AC TIG for aluminum from 0.5 to 5 mm and DC TIG for other metals from 0.5 to 10 mm, so one machine covers both. A DC-only machine welds steel and stainless but not aluminum, and a multi-process machine like the TOOLIOM adds MIG, stick and plasma cutting alongside TIG.
Does a beginner need pulse?
No, but it helps on thin metal. Pulse mode cuts heat input, spatter and distortion, which the ARCCAPTAIN lists as the point of its pulse mode, and the HAXIAOER lists pulse TIG among its modes. Learn the basic arc, then switch pulse on for thin sheet and edge work where burn through is the risk.
Related: best TIG welder, best welder for beginners, the TIG welders hub, and all welders guides.




