Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Single Cut vs Double Cut Carbide Burr: Which One Should You Buy?

Single cut and double cut carbide burrs differ in groove pattern, and these listings show the split through shank sizes, stated hardness and the details each listing leaves unstated.

Single Cut vs Double Cut Carbide Burr: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1LU&MN SC-1 Tungsten Carbide Double-Cut RotaryLU&MN SC-1 Tungsten Carbide Double-Cut Rotary9.6/10View on Amazon
  2. 2Staten Tools SF-1 Carbide Burr 1/4 In Shank DoubleStaten Tools SF-1 Carbide Burr 1/4 In Shank Double9.6/10View on Amazon
  3. 3uxcell Tungsten Carbide Rotary Files 1/8" Shankuxcell Tungsten Carbide Rotary Files 1/8" Shank9.6/10View on Amazon
  4. 4Luo ke 5 Pcs 1/8'' Shank Single Slot AluminumLuo ke 5 Pcs 1/8'' Shank Single Slot Aluminum9.5/10View on Amazon

Verdict. Pick a single cut burr when the work is dense metal or fine detail and the listing points that way; pick a double cut burr when faster removal and a smoother finish claim matter more. The listings here split on shank size too, so match the burr to the collet before weighing cut type.

A burr that chatters, loads up or wanders off the line turns a small cleanup pass into a long chore. The choice between single cut vs double cut carbide burr shapes comes down to groove pattern: a single groove line against a double groove pattern, and each pattern suits a different kind of cut. This comparison puts the listings from both sides next to each other and checks what each listing actually states about shank, hardness, shape and use.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The burrs

LU&MN SC-1 Tungsten Carbide Double-Cut Rotary

LU&MN SC-1 Tungsten Carbide Double-Cut Rotary

LU&MN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A double cut SC-1 cylindrical ball nose burr on a 1/4 inch shank, with a stated hardness up to 1550 (HV30) and a 5/8 in cutting length in the bullets.

Pros

  • Double cut SC-1 shape with a 5/8 in cutting length for deburring, grinding and detailing
  • Stated hardness up to 1550 (HV30) from high density carbide
  • Listing claims smaller chips, faster chip evacuation and less heat build-up
  • 1/4 inch shank fits most die grinders and rotary tools, per the listing

Cons

  • No warranty term is stated
  • No speed range is stated
  • SC-1 cylindrical ball nose is the only shape named in this listing
Staten Tools SF-1 Carbide Burr 1/4 In Shank Double

Staten Tools SF-1 Carbide Burr 1/4 In Shank Double

Staten tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A double cut SF-1 burr on a 1/4 inch (6.35mm) shank, shaped for fine carving, engraving, contouring and edge detailing.

Pros

  • Double cut design the listing claims gives faster cutting, smoother finishes and reduced chatter
  • SF-1 slim profile for tight areas and controlled material removal
  • 1/4 inch (6.35mm) shank fits most rotary tools, die grinders and drill grinders, per the listing
  • Named for steel, stainless steel, cast iron, aluminum, hardwood, plastics, ceramics and composites

Cons

  • No warranty term is stated
  • No hardness figure is stated
  • No cutting length or head diameter is stated
  • No speed range is stated
uxcell Tungsten Carbide Rotary Files 1/8" Shank

uxcell Tungsten Carbide Rotary Files 1/8" Shank

uxcell9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single cut cylindrical radius end burr pair on a 3mm (1/8 inch) shank, made of heat-treated tungsten carbide with hardness above HRA85.

Pros

  • Single groove design the listing points at high-density material: alloy steel, stainless steel and hardened steel
  • Heat-treated tungsten carbide with hardness above HRA85
  • Stated speed range of 4000-50000 rpm
  • Pack holds 2 burrs in the same 3mm size

Cons

  • No warranty term is stated
  • Shank is 3mm (1/8 inch), not the 1/4 inch size of the double cut listings here
  • Hardness is stated on the HRA scale, while the LU&MN and Luo ke listings use HV30 and HRC figures
  • No cutting length is stated apart from the 3mm cutting edge diameter
Luo ke 5 Pcs 1/8'' Shank Single Slot Aluminum

Luo ke 5 Pcs 1/8'' Shank Single Slot Aluminum

Luo ke9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece single slot burr set on a 1/8 inch shank, aimed at aluminum cutting and detail work across wood, metal and plastic.

Pros

  • Pack holds 5 burrs in the same single slot shape
  • 1/8 inch shank fits dremel and most small rotary tools with three jaw chuck, per the listing
  • Stated for aluminum cutting and a broad material list from hard wood to titanium and zinc
  • Tungsten carbide with processing hardness up to HRC58-60

Cons

  • No warranty term is stated
  • No speed range is stated
  • No cutting length, head diameter or listed dimensions are stated
  • Cylindrical radius end is the only shape named in this listing

Other welders and gear to compare

Side by side

LU&MN Double-Cut Burr SC-1 Staten Tools Double Cut Burr SF-1 uxcell Single Cut Rotary Burr 3mm Luo ke Single Slot Burr
Gear Score 59 58 56 55
Cut type Double Cut Double Cut Single Cut Single Slot
Shank 1/4 inch 1/4 inch (6.35mm) 3mm (1/8 inch) 1/8 inch
Pack size 1 1 2 5
Head 5/8 in cutting length SF-1 slim profile 3mm cutting edge diameter Cylindrical radius end
Stated hardness Up to 1550 (HV30) Not stated Above HRA85 Up to HRC58-60
Materials named Metal, wood, plastic Steel, stainless steel, cast iron, aluminum, hardwood, plastics, ceramics, composites Alloy steel, stainless steel, hardened steel Hard wood, balsa, aluminum, copper, metal, steel, plastic, cast iron, cobalt, nickel, titanium, zinc
Warranty Not stated Not stated Not stated Not stated

Ratings in this table are the makers’ own claims taken from each product page (4 November 2026).

Single cut vs double cut carbide burr: what separates the sides

The groove pattern is the split. A single cut burr carries a single groove line, while a double cut burr carries a double groove pattern that the LU&MN listing links to smaller chips and faster chip evacuation. The single cut listings here point at dense metal and detail work, while the double cut listings claim faster removal and smoother finishes. Neither side wins on a spec both sides do not state: where a listing leaves hardness, length or speed unstated, that gap is noted rather than filled in.

Shank size and fit

The uxcell burr uses a 3mm (1/8 inch) shank. The Luo ke set uses a 1/8 inch shank and notes a three jaw chuck for centering on small rotary tools. The LU&MN burr uses a 1/4 inch shank. The Staten Tools burr uses a 1/4 inch (6.35mm) shank. Check the collet size before choosing a cut type, since a burr that does not fit the collet cannot be used at all.

Cut type and removal

The uxcell listing points its single groove design at material of relatively high density, naming alloy steel, stainless steel and hardened steel. The Luo ke listing describes its single slot burr as an aluminum cutting burr and names a broad material list. The LU&MN listing claims its double cut design produces smaller chips, with faster chip evacuation and less heat build-up. The Staten Tools listing claims faster cutting, smoother finishes, reduced chatter and improved control from its double cut design. Finish cannot be scored head to head from these listings alone, since finish claims appear only on the double cut side.

Hardness figures, stated on different scales

The uxcell listing states heat-treated tungsten carbide with hardness above HRA85. The Luo ke listing states processing hardness up to HRC58-60. The LU&MN listing states hardness up to 1550 (HV30). The Staten Tools listing states no hardness figure. Those figures sit on different scales, so they cannot be ranked against each other from these listings alone.

Length and shape gaps

The LU&MN listing gives a 5/8 in cutting length and a 2-3/8 inch total length in the bullets. The same listing’s table lists 3.5 inches x 0.25 inches x 0.25 inches as the product dimensions, which sits apart from the bullets length figure. The Staten Tools listing names the SF-1 shape and a slim profile, without a cutting length or head diameter. The uxcell listing gives a 3mm cutting edge diameter and listed dimensions of 0.79 inches x 0.79 inches x 1.97 inches. The Luo ke listing states no cutting length, head diameter or listed dimensions.

Choose the single cut side if

  • Your work centers on dense metal such as alloy steel, stainless steel or hardened steel.
  • You run a small rotary tool with a 1/8 inch collet.
  • You want one of the multi-burr sets listed here rather than a lone burr.
  • Detail work such as carving, engraving or polishing leads the job.

Choose the double cut side if

  • Faster removal and smoother finishes lead the job.
  • Deburring, grinding and weld seam smoothing fill the day.
  • You run a die grinder with a 1/4 inch collet.
  • Tight areas and controlled removal matter, with an SF-1 slim profile in mind.

Before You Strike an Arc

  • Seat the shank well into the collet and clamp it down tightly before switching on.
  • Match the shank to the collet: the single cut listings here use a 1/8 inch shank, and the double cut listings use a 1/4 inch shank.
  • Check the stated speed range for the burr in hand: only the uxcell listing states a speed range, at 4000-50000 rpm.
  • Wear eye protection and clear loose material from the work area before grinding.
  • Check the shape against the job: SC-1 ball nose for shaping and weld seam smoothing, SF-1 slim profile for tight detail.

FAQ for welders

What is the difference between single cut and double cut carbide burrs?

A single cut burr carries a single groove line, while a double cut burr carries a double groove pattern. The uxcell listing points its single groove design at dense metal. The LU&MN listing claims its double cut design produces smaller chips and faster chip evacuation.

Which cut suits hardened steel?

The uxcell listing names hardened steel among the dense materials its single cut design suits, along with alloy steel and stainless steel. The Staten Tools listing names steel among a broad material list. The LU&MN listing names metal, wood and plastic in general words. Match the burr to the listing that names the metal in the job.

What shank size fits a die grinder?

It depends on the collet in the grinder. The single cut listings here use a 1/8 inch shank, stated as 3mm (1/8 inch) on the uxcell burr. The double cut listings use a 1/4 inch shank, stated as 1/4 inch (6.35mm) on the Staten Tools burr.

Does a double cut burr leave a smoother finish?

The Staten Tools listing claims smoother finishes and reduced chatter from its double cut design. The LU&MN listing claims smooth and precise material removal. No head to head finish figure can be drawn from these listings alone, since finish claims appear only on the double cut side.

Do any of these burrs list a warranty?

No. None of the listings here states a warranty term, so warranty adds nothing to any Gear Score in this comparison. Check the listing again before buying if a written warranty term matters to the job.

Related: best single cut carbide burr, best tungsten carbide burr set, carbide burr vs grinding stone, and what is a die grinder.

Scoring, line by line

Gear Score weighs performance, build and value most, with safety where it applies, and warranty. How we pick explains the weights. No listing here states a warranty term or a safety certification, so safety and warranty add nothing to any score here.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
LU&MN Double-Cut Burr SC-1 9.6 30 21 20 n/a 0
Staten Tools Double Cut Burr SF-1 9.6 29 21 20 n/a 0
uxcell Single Cut Rotary Burr 3mm 9.6 28 20 20 n/a 0
Luo ke Single Slot Burr 9.5 27 19 21 n/a 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

More buying guides

Metal Fab Tools ·

Best Single Cut Carbide Burr (2026)

Four single cut carbide burrs and sets for aluminum and soft metals, compared by cut type, shank size, head dimensions and warranty.