Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Gauntlet vs Short Welding Gloves: Which One Should You Buy?

Gauntlet and short welding gloves compared on cuff coverage, dexterity, heat protection and fit, with four glove listings ranked for MIG, TIG and shop work.

Gauntlet vs Short Welding Gloves: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1FR Pants for Men Flame/Water Resistant Duck Cargo PantFR Pants for Men Flame/Water Resistant Duck Cargo Pant9.6/10View on Amazon
  2. 2BOCOMAL FR Pants for Men Flame Resistant Duck and DenimBOCOMAL FR Pants for Men Flame Resistant Duck and Denim9.5/10View on Amazon
  3. 3BOCOMAL FR Stretch Cargo Pants Lightweight Ripstop RelaxedBOCOMAL FR Stretch Cargo Pants Lightweight Ripstop Relaxed9.5/10View on Amazon
  4. 4DEWALT Premium MIG/TIG Welding GlovesDEWALT Premium MIG/TIG Welding GlovesView on Amazon
  5. 5DEWALT Premium TIG Welding GlovesDEWALT Premium TIG Welding GlovesView on Amazon
  6. 6Miller Performance Welding GlovesMiller Performance Welding GlovesView on Amazon
  7. 7TOOLIOM 932°F Heat-Resistant Leather Welding Gloves forTOOLIOM 932°F Heat-Resistant Leather Welding Gloves forView on Amazon
  8. 8ARCCAPTAIN Soft Goat Grain TIG Welding GlovesARCCAPTAIN Soft Goat Grain TIG Welding GlovesView on Amazon
  9. 9Caiman Premium Split Deerskin MIG/Stick Welding GlovesCaiman Premium Split Deerskin MIG/Stick Welding GlovesView on Amazon

When sparks run down the forearm and the bead needs a steady hand, the cuff decides how much of the arm stays covered. Gauntlet gloves use a long cuff that runs up the forearm and short gloves use a short cuff that covers less of the arm, so gauntlet vs short welding gloves comes down to how much arm coverage the job needs versus how much finger feel it needs. Gauntlet cuffs suit spatter-heavy work, while short cuffs suit fine work where the fingers do the talking.

Other welders and gear to compare

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The difference in one paragraph

A gauntlet cuff runs up the forearm and closes the gap between glove and sleeve, so sparks, slag and spatter have less bare skin to land on. A short cuff, as the Intra-FIT short sleeve description states, covers less of the arm, which leaves more of the forearm to the sleeve but frees the hand for delicate work. The hand part of the glove matters too: cowhide palms are listed as heat-resistant and abrasion-resistant, while the Intra-FIT goatskin glove is listed as high dexterity for TIG work. Cuff length is the headline difference, but palm material and fit decide whether the glove works for a given job.

Side by side

Gauntlet gloves Short gloves Notes
Cuff coverage Long cuff up the forearm; TICONN glove length is 16 inches Short cuff covering less of the arm; Intra-FIT sleeve is short Check the sleeve length description on the listing
Dexterity Varies by palm; TICONN cowhide is 2.4 millimeters Goatskin listed as high dexterity on the Intra-FIT Check the palm material on the listing
Heat and spatter More forearm cover against falling spatter Hand only, forearm left to the jacket sleeve Match the cuff to the process, MIG and stick toward gauntlet
Fit and cuff style Adjustable open cuff or pull-on gauntlet cuff Pull-on short cuff Hook-and-loop adjustment is stated on the DEWALT
Warranty stated DEWALT states a 30 day warranty Intra-FIT states no warranty term TICONN and Miller state no concrete term

Cuff descriptions come from the listings: sleeve length description states Long Sleeve for the gauntlet models here and Short Sleeve for the short model. Always check the sleeve length description on the listing, since makers use cuff names loosely.

When gauntlet is the better choice

  • Spatter-heavy MIG and stick work. A long cuff covers the forearm where spatter falls, which is the whole point of the TICONN glove length of 16 inches and the Miller glove length of 12 inches.
  • Overhead and out-of-position welds. Sparks fall down the arm on overhead work, and a gauntlet cuff closes that gap.
  • Thick material and longer beads. The TICONN lists 2.4 millimeters of cowhide in a 3 layer build, and the Miller lists a cotton fleece insulated palm for medium-duty MIG work.
  • Loose sleeves or short sleeves on the jacket. When the jacket sleeve rides up, the gauntlet cuff is the backup layer.

When short is the better choice

  • Fine TIG work. A short goatskin glove, such as the Intra-FIT listed as high dexterity, gives finger feel for torch control and filler rod work.
  • Bench work with the forearm resting. A short cuff does not bunch at the wrist when the forearm sits on the bench.
  • Hot shop days. Less cuff means less material on the arm, though the hand still needs the same heat protection.
  • Quick on and off. A pull-on short cuff, as the Intra-FIT lists, slips off without a strap or buckle between welds.

How to choose: gauntlet vs short welding gloves

Start with the process. MIG and stick throw more spatter than TIG, so they push toward a gauntlet cuff, while TIG pushes toward dexterity and a short or slim gauntlet cuff. The DEWALT shows the middle ground: a gauntlet-style open cuff with a seamless index finger, listed to promote accurate welds, plus Kevlar threading throughout and an EN407 standard level 1 rating for contact heat. Next, check fit on the listing size chart rather than guessing. The TICONN lists a hand size figure of 5.5 for 16 inch L, 6.1 for 16 inch XL and 6.5 for 16 inch XXL, so measure the hand and match the chart. Finally, check the heat claims with their conditions: the TICONN title claims 1000°F heat resistance, while its fur description states palm contact heat at 932°F for 16 secs, so read the contact rating, not just the headline.

The gloves in this guide

The TICONN 16 inch glove: a 16 inch glove length, 2.4 millimeters of cowhide in a 3 layer build of cowhide leather, insulated aluminum foil and flame retardant cotton, reinforced stitching, and a palm contact heat figure of 932°F for 16 secs. Its size is listed as 16 inch XL, and no concrete warranty term is stated, since the warranty field only points to warranty information elsewhere. The DEWALT Premium TIG glove offers a gauntlet-style open cuff with a hook-and-loop adjustable design, Kevlar threading throughout, a seamless index finger and an EN407 standard level 1 contact heat rating, at 7.36 ounces and 15.25 x 5.75 x 0.7 inches in size Large. It is the only glove here with a concrete warranty term, a 30 day warranty against manufacturer defects. The Intra-FIT TIG glove is the short option: premium goatskin with a keystone thumb, Kevlar stitching, a short sleeve length description, a size of Large and item dimensions of 9.8 x 4.7 x 1.5 inches. Its warranty description states NO, so no warranty term is stated for this glove. The Miller Performance glove has a gauntlet cuff with a keystone thumb, premium cowhide, a 12 inch glove length and a cotton fleece insulated palm, listed for medium-duty MIG welding and metalworking. Note a contradiction inside the Miller listing: one field lists an item weight of 0.27 g while the product dimensions list 0.01 ounces, so treat the weight as unstated and judge the glove on its stated length and palm.

Can one pair do both?

Yes, and for many home shops that is the practical answer: a gauntlet TIG glove, such as the DEWALT, covers the forearm while keeping a seamless index finger for torch work. A short goatskin glove stays the pick for the finest TIG work, and a long cowhide gauntlet stays the pick for heavy spatter. If the shop does both, own a pair of each cuff style and grab the one that fits the job on the bench.

Heat, sparks and fumes. Gloves cover the hands, and gauntlet cuffs add forearm cover, and they do not replace a helmet, ventilation or fire watch. Weld with good ventilation or outdoors with the head out of the plume, keep flammable material clear of the work area, and check the listing rating before trusting a glove against a hazard its rating does not cover.

FAQ for welders

Which cuff is better for MIG welding?

A gauntlet cuff is the safer pick for MIG work, since MIG throws spatter that falls on the forearm. The TICONN glove length of 16 inches and the Miller glove length of 12 inches both run well past the wrist, while a short cuff leaves the forearm to the jacket sleeve alone.

Which cuff is better for TIG welding?

A short goatskin glove, such as the Intra-FIT listed as high dexterity, gives the most finger feel for torch and filler work. A gauntlet TIG glove, such as the DEWALT with its seamless index finger, is a middle ground that keeps forearm coverage without giving up torch control.

Can short gloves handle stick welding spatter?

Short gloves protect the hand, but the forearm stays exposed, so stick work with heavy spatter calls for a gauntlet cuff or a jacket sleeve that fully covers the forearm. If the jacket sleeve is long and stays put, a short glove can work, but the margin is thinner than with a gauntlet cuff.

How do I pick the right glove size?

Measure the hand and match the listing size chart, since makers size differently. The TICONN lists a hand size figure of 5.5 for 16 inch L, 6.1 for 16 inch XL and 6.5 for 16 inch XXL, while the DEWALT in this guide is listed in size Large with a hook-and-loop adjustable cuff for a snug fit.

Do any of these gloves state a warranty?

Only the DEWALT states a concrete term, a 30 day warranty against manufacturer defects. The TICONN and Miller warranty fields only point to warranty information elsewhere, and the Intra-FIT warranty description states NO, so no concrete warranty term is stated for those three.

Related: best leather welding gloves, best TIG welding gloves, best welding gloves for MIG, and the welding safety gear hub.

More buying guides