Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Cordless vs Corded Plasma Cutter: Which One Should You Buy?

Cordless vs corded plasma cutter answered: when battery power is worth it, when a corded machine wins, and three listed corded plasma cutters as examples.

Cordless vs Corded Plasma Cutter: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 150A Plasma Cutter Machine50A Plasma Cutter MachineView on Amazon
  2. 2ARCCAPTAIN iControl CUT55 Prolux Plasma Cutter MachineARCCAPTAIN iControl CUT55 Prolux Plasma Cutter MachineView on Amazon
  3. 3ARCCAPTAIN 55A Non-HF Plasma Cutter MachineARCCAPTAIN 55A Non-HF Plasma Cutter MachineView on Amazon
  4. 4YESWELDER 5-in-1 TIG Welder & Plasma CutterYESWELDER 5-in-1 TIG Welder & Plasma CutterView on Amazon
  5. 5SILATU 55A Plasma Cutter MachineSILATU 55A Plasma Cutter MachineView on Amazon
  6. 6Plasma Cutter Welder Combo 160APlasma Cutter Welder Combo 160AView on Amazon

Cordless vs corded plasma cutter comes down to where you cut. A cordless cutter runs on battery packs, so it works away from an outlet. A corded cutter plugs into 110V or 220V and runs as long as the power holds. All three machines listed below are corded dual-voltage models, so they show the corded side in detail.

Other welders and gear to compare

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The difference in one paragraph

A plasma cutter needs two things: electricity to make the arc and compressed air to blow the molten metal out of the cut. Corded machines take electricity from a wall outlet, at 110V, 220V or both; the listed amperage is what sets how thick they cut. Cordless machines take it from battery packs, which frees them from the outlet but ties cutting time to the charge. Either way, the air still comes from a compressor.

Cordless vs corded plasma cutter side by side

Cordless Corded Note
Power source Battery packs 110V/220V outlet All three listings are corded
Best setting Away from outlets Home shop with power Match to where you cut
Cut capacity Varies by model 50A bestarc, 55A ARCCAPTAIN models Listings cut 1/2 in to 1 in
Air supply Still needs a compressor External compressor listed Not included in any listing
Runtime Limited by battery charge Runs while power holds No cordless model listed here
Setup No outlet needed Needs the right outlet bestarc lists breaker sizes

All three listings below are corded dual-voltage machines; no cordless model is listed here, so the cordless column describes the category in general terms.

When cordless is the better choice

  • Work away from outlets. Fence lines, remote equipment and field repairs where dragging a cord and an air hose is impractical.
  • Short cuts. A few cuts per visit rather than all-day production, since cutting time follows the battery charge.
  • Quick setup. No outlet hunting and no long extension cord runs before the first cut.

When corded is the better choice

  • Home shop work. The three listings here run on 110V/220V or 120V/240V, so a garage with the right outlet covers them.
  • Longer cutting sessions. A corded machine runs as long as the power and air hold, with no battery to swap mid-job.
  • Thicker metal. The listed corded machines run at 50A for the bestarc and 55A for both ARCCAPTAIN models, with the ARCCAPTAIN models cutting up to 7/8 in and 1 in.

The gear: three corded examples

1. ARCCAPTAIN CUT55 Prolux. The most featured of the three: a 55A dual-voltage 120V/240V machine with app control for adjusting parameters from up to 10 meters, expanded metal and rust removal modes, and smart air pressure detection. The listing states 7/8 in cutting at 240V, a 3-year warranty and ANSI certification. Who it is for: home DIY users who want remote control and the longest stated warranty here.

2. ARCCAPTAIN 55A Non-HF. The rugged one: a 55A dual-voltage 110V/220V machine with a blowback non-high-frequency pilot arc, an IPT60 torch and a 1 in max cut. The listing states 3/5 in clean cuts, E80 and E81 air pressure warnings, and IP21 water resistance, with overload, overheating and overcurrent protection. Who it is for: garage and workshop users who want the deepest listed max cut with clear fault codes.

3. bestarc 50A. The straightforward one: a 50A dual-voltage 110V/220V machine with an AG60P pilot arc torch, a digital LED screen and a built-in air sensor. The listing states 1/2 in clean cuts and 2/3 in max cut, with 2T/4T modes and PA/PT adjustment for mesh cutting. Who it is for: home DIY users who want pilot arc starting on rusted or painted metal at 50A.

How to tell what a machine supports

Read the voltage line first: the listings here state 110V/220V or 120V/240V dual voltage, and the bestarc listing names the recommended breakers at 40A for 110V and 30A for 220V. Check the cut capacity in the same units the listing uses, since the ARCCAPTAIN Prolux lists 7/8 in while the Non-HF lists a 1 in max cut. Confirm the air requirement: all three listings need an external air compressor, which is not included, and state recommended pressures around 50 to 75 PSI.

Do cordless models still need an air compressor?

Yes. The battery replaces the power cord, not the air supply: a plasma cutter still needs dry, compressed air to make the cut. The bestarc listing recommends dry compressed air and notes the compressor is not included, and the ARCCAPTAIN Non-HF listing says the same. Budget for the compressor and the air filter setup either way.

FAQ for welders

Can a cordless plasma cutter cut as thick as a corded one?

That depends on the model, and no cordless model is listed here. The three corded listings state 50A for the bestarc and 55A for both ARCCAPTAIN models, with cuts from 1/2 in clean to 1 in max. Compare the amperage and cut figures of any cordless model against those before deciding.

What voltage do these three listings need?

All three are dual voltage: the bestarc and the ARCCAPTAIN Non-HF list 110V/220V, and the ARCCAPTAIN Prolux lists 120V/240V. Check that your outlet and breaker match the listing.

Is an air compressor included?

No. The bestarc and the ARCCAPTAIN Non-HF listings state an external air compressor is required and not included. Those two listings include air filters and quick-connect fittings for hooking one up.

What is a pilot arc?

The bestarc listing describes its AG60P pilot arc torch as starting the arc without touching the metal, which suits rusted, painted or dirty surfaces. The ARCCAPTAIN Non-HF lists a blowback pilot arc for the same purpose.

Related: best portable plasma cutter, best home hobby plasma cutter, 120V vs 240V plasma cutter, best air compressor for plasma cutter, and the plasma cutters hub.

More buying guides