Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Welding Table Leveling Feet Under $15 (2026): 5 Picks

Five screw-in leveling feet under 15, compared on thread, load rating, base and pack count for steadying a welding table on an uneven floor.

Best Welding Table Leveling Feet Under $15 (2026): 5 Picks
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1NEWBYTEK Leveling FeetBest OverallNEWBYTEK Leveling Feet9.6/10View on Amazon
  2. 2POWERTEC Leveling FeetHighest Load RatingPOWERTEC Leveling Feet9.6/10View on Amazon
  3. 3NANMOTUE Leveling FeetWidest Height RangeNANMOTUE Leveling Feet9.6/10View on Amazon
  4. 4tibaebe Leveling FeetBest Pack Counttibaebe Leveling Feet9.5/10View on Amazon
  5. 5Bonsicoky Leveling FeetBest SwivelBonsicoky Leveling Feet9.4/10View on Amazon

A welding table that rocks on a garage slab makes every fit-up fight back. A leg sits low, the table tips when you lean into a bead, and the work shifts mid-weld. Screw-in leveling feet fix that without rebuilding the table: they thread into the leg, wind up or down to meet the floor, and hold the top still. This guide compares the best welding table leveling feet under 15 on thread, load rating, base size and pack count, using only what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall NEWBYTEK Leveling Feet: 400 pounds per foot, 2 inch nylon base, felt pads and T-nuts in the box. Check price on Amazon
  • Highest Load Rating POWERTEC Leveling Feet: 550 pounds per foot, the highest stated rating here, on a 3/8-16 insert. Check price on Amazon
  • Widest Height Range NANMOTUE Leveling Feet: Adjusts from 3/4 inch to 1-3/4 inch with steel T-nuts and felt pads. Check price on Amazon
  • Best Pack Count tibaebe Leveling Feet: 15 feet in the box for several tables, desks and cabinets. Check price on Amazon
  • Best Swivel Bonsicoky Leveling Feet: Swivels from 90 degrees to 60 degrees with rubber pads for uneven floors. Check price on Amazon

The machines

NEWBYTEK 3/8-16 Heavy Duty Leveling Feet

NEWBYTEK 3/8-16 Heavy Duty Leveling Feet

NEWBYTEK9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of 4 heavy duty 3/8-16 leveling feet with a 2 inch nylon base, felt pads and round T-nuts, rated at 400 pounds per foot.

Pros

  • 400 pounds per foot, 1600 pounds per set
  • 2 inch nylon base with felt pads for floor protection
  • Round T-nuts with 3 holes spread the load and resist wood splits
  • Made for sloped workbenches and pitched garage concrete floors

Cons

  • No warranty term is stated
  • Not for metric M10 holes
  • Needs a 1/2 inch hole over 2 inches deep in wood legs
  • Tall 2.75 inch profile adds height to the table
POWERTEC Threaded Leveling Feet 4PK with 3/8"-16

POWERTEC Threaded Leveling Feet 4PK with 3/8"-16

POWERTEC9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of 4 heavy duty leveling feet with 3/8-16 threaded inserts, a large nylon foot and a 550 pound rating per foot.

Pros

  • 550 pounds per foot, 2,200 pounds per set
  • Carbon steel with zinc-plated threaded inserts for corrosion resistance
  • Large nylon base helps protect floors and furniture surfaces
  • Tapered insert suits cabinets, benches, tables and equipment racks

Cons

  • No warranty term is stated
  • Not ideal for soft wood and high gloss finish flooring
  • Hex wrenches for install are not included
  • Recommended T-wrench is not in the box
NANMOTUE Leveling Feet Adjustable Furniture Feet

NANMOTUE Leveling Feet Adjustable Furniture Feet

NANMOTUE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of 4 adjustable leveling feet with a 3/8-16 thread, steel T-nuts and felt pads, rated at 330 pounds per foot.

Pros

  • Adjustable height from 3/4 inch to 1-3/4 inch
  • Steel T-nuts and a 1.75 inch steel insert for support
  • 330 pounds per foot, 1320 pounds per set
  • 8 felt pads included to protect floors from scratches

Cons

  • No warranty term is stated
  • Needs a pre-drilled 1/2 inch hole 1-1/2 inches deep
  • Works with 3/8-16 thread only, so it will not fit metric legs
1/4" Thread Furniture Feet Levelers

1/4" Thread Furniture Feet Levelers

tibaebe9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 15-piece set of 1/4-20 screw-in leveling feet with a galvanized steel body and a non-skid PP base, rated over 200 pounds.

Pros

  • 15 feet in the box, enough for several pieces of furniture
  • 1/4-20 thread is a common size for American furniture feet
  • Galvanized steel with a black PP non-skid base
  • Install takes less than 5 minutes with no complicated tools

Cons

  • No warranty term is stated
  • T-nuts are not included
  • 1/4-20 thread will not fit 3/8-16 legs
  • 1 inch base is the smallest here
Bonsicoky M8 Metal Adjustable Leveling Feet

Bonsicoky M8 Metal Adjustable Leveling Feet

Bonsicoky9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of 4 M8 swivel leveling feet with rubber pads, adjustable from 90 degrees to 60 degrees for uneven floors.

Pros

  • Swivel adjustment from 90 degrees to 60 degrees for uneven floors
  • Rubber pads protect floors from scratches
  • Screws directly into threaded furniture bases
  • Steel, rubber and nylon construction

Cons

  • No load capacity is stated
  • M8 thread will not fit 3/8-16 legs
  • No warranty term is stated

Other welders and gear to compare

Spec sheet comparison

Foot Gear Score Thread Load per foot Base Pack
NEWBYTEK Leveling Feet 9.6/10 3/8-16 UNC 400 pounds 2 inch nylon 4 pack
POWERTEC Leveling Feet 9.6/10 3/8-16 550 pounds 1-3/8 inch nylon 4 pack
NANMOTUE Leveling Feet 9.6/10 3/8-16 UNC 330 pounds 1-3/8 inch nylon 4 pack
tibaebe Leveling Feet 9.5/10 1/4-20 UNC Over 200 pounds 1 inch PP 15 pack
Bonsicoky Leveling Feet 9.4/10 M8 Not stated Rubber pad 4 pack

Ratings in this table are the makers’ own claims taken from each product page (28 October 2026). Where a listing states a figure two ways, the table shows both.

How to choose the best welding table leveling feet under 15

Thread before anything else

Thread decides fit before anything else. Three of these feet use a 3/8-16 thread, the size the NEWBYTEK, POWERTEC and NANMOTUE listings share, while the tibaebe feet use a 1/4-20 thread and the Bonsicoky feet use an M8 thread. A foot with the wrong thread will not screw into the leg at all, so match the thread to the leg before looking at load ratings or base size. NEWBYTEK warns its feet are not for metric M10 holes and asks buyers to measure the hole diameter and thread count.

Load rating per foot, not per set

Listings quote capacity two ways, per foot and per set, and the per-foot figure is the one that matters when a heavy table loads one leg harder than the rest. POWERTEC rates each foot at 550 pounds and the set of 4 at 2,200 pounds, NEWBYTEK rates each foot at 400 pounds and the set at 1600 pounds, and NANMOTUE rates each foot at 330 pounds and the set at 1320 pounds. The tibaebe listing states support over 200 pounds, and the Bonsicoky listing states no load capacity at all, so its rating cannot be compared. For a welding table, pick a per-foot rating with room above the heaviest load one leg will carry.

Base size and floor protection

The base is what meets the floor, and a wider base spreads the load while pads keep the floor intact. NEWBYTEK uses a 2 inch nylon base with felt pads, POWERTEC and NANMOTUE use a 1-3/8 inch base with nylon or felt pads, and the Bonsicoky feet use rubber pads. The tibaebe feet use a black PP non-skid base at 1 inch across. On rough concrete, a nylon base holds up better than brittle plastic, per the NEWBYTEK listing, while felt pads let heavy pieces slide on indoor hardwood without scratches. POWERTEC warns its feet are not ideal for soft wood and high gloss finish flooring, so check the floor type before choosing.

Height adjustment and installation

Adjustment range decides whether a foot can take up a real gap. NANMOTUE adjusts from 3/4 inch to 1-3/4 inch, NEWBYTEK lists tall 2.75 inch levelers for sloped floors, and Bonsicoky swivels from 90 degrees to 60 degrees for stability on uneven floors. Installation is screw-in across all five listings: NANMOTUE and NEWBYTEK include T-nuts and ask for a 1/2 inch pre-drilled hole, POWERTEC uses a tapered threaded insert and suggests a trial fit on scrap wood of the same species, and tibaebe notes T-nuts are not included and installation takes less than 5 minutes. Match the install method to the leg: wood legs take T-nuts, while NEWBYTEK notes metal legs can take welded 3/8 inch inserts.

Before You Strike an Arc

  • Confirm the leg thread before ordering: 3/8-16, 1/4-20 and M8 feet do not interchange.
  • Pre-drill the hole to the size the listing asks, 1/2 inch for the T-nut feet, and trial-fit on scrap wood of the same species where the listing suggests it.
  • Check the floor under the table: felt pads for indoor hardwood, rubber pads for grip, and a wider nylon base for rough concrete.
  • Count the feet in the box: four-foot sets suit a four-leg table, while the 15-piece tibaebe set covers spare legs and extra benches.

FAQ for welders

What thread size fits a welding table leg?

It depends on the leg. Three listings here use 3/8-16 thread, one uses 1/4-20 thread, and one uses M8 thread, so check the leg or the existing insert before ordering. NEWBYTEK warns its 3/8-16 feet are not for metric M10 holes. When the leg has no thread at all, the T-nut feet from NANMOTUE and NEWBYTEK give you a threaded socket to screw into.

How much weight can leveling feet hold?

Per-foot ratings here run from over 200 pounds on the tibaebe feet to 550 pounds on the POWERTEC feet, with NEWBYTEK at 400 pounds and NANMOTUE at 330 pounds per foot. Set ratings follow the same order, from 1320 pounds to 2,200 pounds for the four-foot sets. The Bonsicoky listing states no load capacity, so its rating cannot be compared with the rest.

Do leveling feet protect the floor?

Yes, through the base material and pads. Nylon bases and felt pads guard against scratches, rubber pads add grip, and the tibaebe feet use a non-skid PP base. POWERTEC is the exception to check: its listing says the feet are not ideal for soft wood and high gloss finish flooring. Match the pad to the floor, not just to the table.

Can leveling feet fix a sloped garage floor?

They can take up unevenness within their adjustment range. NEWBYTEK pitches its feet for sloped workbenches and pitched garage concrete floors, and Bonsicoky swivels from 90 degrees to 60 degrees for stability on uneven floors. For a large slope, measure the gap before choosing and pick a foot whose adjustment range covers it.

Do I need T-nuts to install leveling feet?

It depends on the foot. NANMOTUE and NEWBYTEK include T-nuts in the box, so a pre-drilled hole takes the insert and the foot screws in. POWERTEC uses a tapered threaded insert instead, and tibaebe states T-nuts are not included, so those need a threaded leg or a separately bought insert. Check the box contents before drilling.

Related: best welding table for home shop, best welding table leveling feet, and how to build a welding table. Also see welding table wheels vs fixed legs and the welding tables and carts hub.

Scoring, line by line

Each foot is scored on performance, build, value, safety listing and warranty. A spec the listing does not publish scores nothing, and no pick here states a safety certification or a warranty term, so those two scores sit at zero across the board.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
NEWBYTEK Leveling Feet 9.6 30 21 21 n/a 0
POWERTEC Leveling Feet 9.6 29 21 20 n/a 0
NANMOTUE Leveling Feet 9.6 28 20 20 n/a 0
tibaebe Leveling Feet 9.5 26 19 21 n/a 0
Bonsicoky Leveling Feet 9.4 24 19 19 n/a 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.

More buying guides