Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Welding Table Leveling Feet (2026): 5 Picks for a Steady Table

Five leveling foot sets for a welding table, compared on thread, stated capacity, adjustment range, mounting hardware and the warranty each listing states.

Best Welding Table Leveling Feet (2026): 5 Picks for a Steady Table
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Anwenk 3/8-16 4-PackBest OverallAnwenk 3/8-16 4-Pack9.6/10View on Amazon
  2. 2POWERTEC 71136Best for WorkbenchesPOWERTEC 711369.6/10View on Amazon
  3. 3LOSCHEN L-Bracket 4-PackWidest AdjustmentLOSCHEN L-Bracket 4-Pack9.4/10View on Amazon
  4. 4Celuisiva 1/4 in 12-PackBiggest PackCeluisiva 1/4 in 12-Pack9.3/10View on Amazon

A table that rocks on a shop slab turns every fit-up into a fight. The tack cools crooked, the square walks off the joint, and you spend the weld chasing the wobble instead of watching the puddle. That is the job the best welding table leveling feet solve: screw-in feet that take up the uneven floor under each leg so the top stays put. This roundup scores five screw-in leveling foot sets on thread, stated capacity, adjustment range and mounting hardware for use under a steel table.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Anwenk 3/8-16 4-Pack: Stated 1320 lb capacity, steel T-nuts and threaded inserts, 3/4 to 1 3/4 in adjustment, and the only stated warranty here, 6 months. Check price on Amazon
  • Best for Workbenches POWERTEC 71136: Zinc-plated steel, 600 lb per set, an L-shaped ledge that carries the load, and a listing that names workbenches and tables as uses. Check price on Amazon
  • Widest Adjustment LOSCHEN L-Bracket 4-Pack: A 0.78 to 2-2/5 in range on a 3/8-16 shaft, with an L-bracket mount and a rubber foot cap. Check price on Amazon
  • Biggest Pack Celuisiva 1/4 in 12-Pack: Twelve 1/4″-20 feet with T-nuts, though 200 lb per foot suits light builds only. Check price on Amazon

The machines

Adjustable Leveling Feet Furniture Levelers Table

Adjustable Leveling Feet Furniture Levelers Table

Anwenk9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-pack of 3/8-16 leveling feet with steel T-nuts and threaded inserts, a stated 1320 lb capacity and the only stated warranty in this roundup.

Pros

  • Stated 1320 lb capacity, 330 lb per foot
  • Steel T-nuts and 1.75 in threaded inserts included
  • Adjusts from 3/4 to 1 3/4 in, per the listing
  • 6 month manufacturer warranty is stated

Cons

  • No safety certification is stated
  • 1320 lb figure is the maker's claim; no measurement method is stated
  • Felt pads ship as separate pieces
  • Legs without 3/8-16 thread need a pre-drilled 1/2 in hole
POWERTEC Leveling Feet 4PK

POWERTEC Leveling Feet 4PK

POWERTEC9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A zinc-plated steel 4-pack with an L-shaped ledge that carries the load, a stated 600 lb per set capacity and a full install kit.

Pros

  • L-shaped ledge transfers weight to the leveler, not the screws
  • Zinc-plated steel construction, per the listing
  • Full kit: 4 levelers, 4 lock nuts, 16 screws, 5 mm hex wrench
  • Listing names workbenches, tables and cabinets as uses

Cons

  • Stated capacity is 600 lb per set, lower than the 1320 lb picks
  • No adjustment range is stated
  • No warranty term is stated
  • Not ideal for soft wood and high gloss floors, per the listing
3/8" Threaded Leveling Feet Adjustable

3/8" Threaded Leveling Feet Adjustable

TWIG9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/8-16 4-pack with a stated 1320 lb capacity, 1 to 2 in of adjustment and furniture pads included, with install notes for metal legs.

Pros

  • Stated 1320 lb maximum load
  • Adjusts from 1 to 2 in, per the listing
  • Includes 8 furniture pads, 4 for use and 4 replacements
  • Listing explains metal-leg install: weld a 3/8 in threaded insert

Cons

  • No warranty term is stated
  • Needs a 1/2 in hole deeper than 1-1/2 in plus a T-nut per leg
  • Legs under 1-1/2 in diameter risk cracking at install, per the listing
LOSCHEN 4 PCS Heavy Duty Adjustable Leveling Feet

LOSCHEN 4 PCS Heavy Duty Adjustable Leveling Feet

LOSCHEN9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-pack on 3/8-16 shafts with an L-bracket mount, a stated 880 lb capacity and the widest stated adjustment range here.

Pros

  • Widest stated range: 0.78 to 2-2/5 in
  • Stated 880 lb capacity, 220 lb per leg
  • L-bracket hooks under the leg edge to spread the load
  • Rubber cap protects floors and blocks moisture

Cons

  • No warranty term is stated
  • Alloy steel with no stated finish
1/4" Thread Leveling Feet

1/4" Thread Leveling Feet

Celuisiva9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12-pack of 1/4"-20 feet with T-nuts for light builds, with the lowest stated capacity and the smallest adjustment range here.

Pros

  • 12 feet with T-nuts in one pack
  • Galvanized steel with a black PP base, per the listing
  • Fits 1/4 in legs with a 1/3 or 5/16 in drill bit for the T-nut
  • Suits uneven wood, tile, hardwood, laminate and carpet, per the listing

Cons

  • Lowest stated capacity: 200 lb per foot, for light furniture
  • Smallest thread here at 1/4"-20
  • Narrowest stated range: 1/3 to 3/4 in
  • No warranty term is stated

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Thread / mount Stated capacity Adjustment range Warranty
Anwenk 3/8-16 4-Pack 9.6/10 3/8-16, T-nut 1320 lb 3/4 to 1 3/4 in 6 months
POWERTEC 71136 9.6/10 L-ledge, screws 600 lb per set Not stated None stated
TWIG 3/8-16 4-Pack 9.5/10 3/8-16, T-nut 1320 lb 1 to 2 in None stated
LOSCHEN L-Bracket 4-Pack 9.4/10 3/8-16 shaft, L-bracket 880 lb 0.78 to 2-2/5 in None stated
Celuisiva 1/4 in 12-Pack 9.3/10 1/4″-20, T-nut 200 lb per foot 1/3 to 3/4 in None stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 23 October 2026.

Buying guide: best welding table leveling feet for the home shop

Thread and mounting

Thread decides what the foot screws into. Three of the five use a 3/8-16 thread: the TWIG and Anwenk screw into a T-nut or threaded insert, and the LOSCHEN uses a 3/8-16 shaft on an L-bracket that hooks under the leg edge. The Celuisiva uses a smaller 1/4″-20 thread with T-nuts. The POWERTEC has no threaded stud; its L-shaped ledge screws to the leg with the included screws and lock nuts, so the leg itself carries no thread.

Stated capacity

Stated capacities run from 200 lb per foot on the Celuisiva to 1320 lb per set on the TWIG and Anwenk, with the POWERTEC at 600 lb per set and the LOSCHEN at 880 lb. No listing says how the figure was measured, so treat it as the maker’s claim and keep the table’s real load, steel top included, under it.

Adjustment range

The range decides how much floor unevenness the foot can take up. The TWIG adjusts from 1 to 2 in, the Anwenk from 3/4 to 1 3/4 in, the LOSCHEN from 0.78 to 2-2/5 in, and the Celuisiva from 1/3 to 3/4 in. The POWERTEC listing states no adjustment range, so its travel is not stated. Match the range to the worst dip in your slab.

Floor protection

Steel feet chew concrete and mark tile. The Anwenk has a nylon bottom for all floors plus felt pads for hardwood, the LOSCHEN a rubber cap that also blocks moisture, and the TWIG ships 8 furniture pads, 4 for use and 4 as replacements. The POWERTEC nylon base suits hardwood, tile and concrete, though the listing says it is not ideal for soft wood and high gloss floors.

What comes in the box

Count the hardware before you plan the install. The Anwenk, POWERTEC and LOSCHEN kits include lock nuts, screws and a hex wrench, 5 mm on the POWERTEC and LOSCHEN. The TWIG includes T-nuts and 8 pads, and the Celuisiva 12-pack includes T-nuts. A kit with lock nuts matters on a table that takes hammering and grinding vibration.

Use as directed. For steel legs, the TWIG listing says to weld a 3/8 in threaded insert into the leg before screwing the foot in; do not force a wood T-nut into steel. Never exceed the stated capacity, keep the area under the table clear of spatter, and confirm the lock nuts are tight before the first arc.

Before You Strike an Arc

  • Check the leg thread first: 3/8-16 on the TWIG, Anwenk and LOSCHEN picks, 1/4″-20 on the Celuisiva, and no thread on the POWERTEC, which screws on with its own hardware.
  • Steel legs need steel threads: the TWIG listing calls for a welded 3/8 in threaded insert in metal legs.
  • Measure the floor dip against the stated range: 1 to 2 in on the TWIG, 3/4 to 1 3/4 in on the Anwenk, 0.78 to 2-2/5 in on the LOSCHEN, 1/3 to 3/4 in on the Celuisiva; the POWERTEC range is not stated.
  • Tighten the lock nuts, included with the Anwenk, POWERTEC and LOSCHEN, so shop vibration does not walk the feet out of adjustment.
  • Keep the loaded table under the stated capacity: 1320 lb on the top two picks, 600 lb on the POWERTEC, 880 lb on the LOSCHEN, and 200 lb per foot on the light-duty Celuisiva.

FAQ for welders

How do you level a welding table with leveling feet?

Screw a foot into each leg, set the table where it will live, then turn each foot until the top sits flat and the rocking stops. Feet with a lock nut, like the Anwenk, POWERTEC and LOSCHEN picks, get the nut tightened against the leg or bracket so vibration does not move the setting.

What thread size fits a welding table leg?

Three picks here use 3/8-16 thread and the Celuisiva uses 1/4″-20, all with T-nuts for wood legs. For steel legs the TWIG listing says to weld a 3/8 in threaded insert into the leg first, then screw the foot in. The POWERTEC skips threads entirely and screws its L-ledge to the leg with the included screws and lock nuts.

How much weight can leveling feet hold?

The listings state 1320 lb per set for the TWIG and Anwenk, 600 lb per set for the POWERTEC, 880 lb for the LOSCHEN and 200 lb per foot for the Celuisiva. None says how the figure was measured, so treat it as the maker’s claim and keep the full table weight under it.

Will leveling feet protect my shop floor?

The nylon and rubber feet here are made for that: the Anwenk lists a nylon bottom for all floors with felt pads for hardwood, and the LOSCHEN a rubber cap that also blocks moisture from the foot. The TWIG includes furniture pads, and the POWERTEC nylon base suits hardwood, tile and concrete, though the listing warns it is not ideal for soft wood and high gloss floors.

Can I put leveling feet on steel table legs?

Yes, with the right mount. The TWIG listing is explicit: weld a 3/8 in threaded insert into a metal leg, then screw the foot in. The LOSCHEN L-bracket hooks under the leg edge and screws on, and the POWERTEC L-ledge screws to the leg with lock nuts. Drill and T-nut installs suit wood legs only.

Related: the welding tables and carts hub, portable vs stationary welding table, how to build a welding table and best welding table size.

Scoring, line by line

Each foot set is scored out of 10 on performance, build, value, safety listing and warranty. None of these listings states a safety certification, so every pick here scores zero on that criterion; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Anwenk 3/8-16 4-Pack 9.6 28 20 20 n/a 1
POWERTEC 71136 9.6 27 21 20 n/a 0
TWIG 3/8-16 4-Pack 9.5 26 19 19 n/a 0
LOSCHEN L-Bracket 4-Pack 9.4 24 19 19 n/a 0
Celuisiva 1/4 in 12-Pack 9.3 20 16 19 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

More buying guides