Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Shop Press Sleeve Kit (2026): 4 Kits Compared

Four press sleeve kits for a hydraulic shop press, compared on sleeve sizes, pulling spindles, steel, storage, and the warranty each listing states.

Best Shop Press Sleeve Kit (2026): 4 Kits Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Orion Motor Tech 27-PieceBest OverallOrion Motor Tech 27-Piece9.6/10View on Amazon
  2. 2KTPROT 34-PieceFor Hydraulic Shop PressKTPROT 34-Piece9.5/10View on Amazon
  3. 3DAYUAN 26-PieceDrop Forged SteelDAYUAN 26-Piece9.5/10View on Amazon
  4. 4WINMAX 28-Piece28-Piece KitWINMAX 28-Piece9.4/10View on Amazon

A bearing that will not move is the job that stops a Saturday. The control arm is off the car, the bushing is seized in its housing, and the press is waiting for a sleeve that fits the bore and a spindle that pulls it through without chewing the housing. That is the job a best shop press sleeve kit is made for, and this guide compares the kits on sleeve sizes, spindles, steel, storage and warranty.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Orion Motor Tech 27-Piece: 22 sleeves from 34 to 80 mm, 5 pulling spindles to M18, notched sleeves and a blow-molded case, with a 1 year warranty. Check price on Amazon
  • For Hydraulic Shop Press KTPROT 34-Piece: 27 sleeves made for a hydraulic shop press, with an adapter, 6 centering pins, a case and gloves, and a 1 year warranty. Check price on Amazon
  • Drop Forged Steel DAYUAN 26-Piece: 20 sleeves from 34 to 72 mm in 2 mm steps, 4 pulling spindles with thrust bearings, drop forged and heat treated, with a 1 year warranty. Check price on Amazon
  • 28-Piece Kit WINMAX 28-Piece: 28 pieces with sleeves from 34 to 72 mm inside diameter for bearings, bushes and seals, with a 1 year warranty. Check price on Amazon

The machines

OMT Bushing Press Kit, Pull and Press Sleeve Kit

OMT Bushing Press Kit, Pull and Press Sleeve Kit

Orion Motor Tech9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 27-piece kit with 22 sleeves from 34 to 80 mm, 5 pulling spindles to M18, notched sleeves and a blow-molded case.

Pros

  • 22 sleeves with bores from 34 to 80 mm, the widest range here
  • 5 pulling spindles in M10, M12, M14, M16 and M18
  • Notched sleeves catch the bushing edge and show its position
  • Blow-molded case keeps the 27 pieces organized for carry

Cons

  • 38.4 lb, heavy to carry to a job away from the shop
  • Bore range tops out at 80 mm, so larger housings need a bigger kit
  • No adapter or centering pins in the box
  • No gloves in the box
KTPROT 34Pcs Bushing Press Kit

KTPROT 34Pcs Bushing Press Kit

KTPROT9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 34-piece kit made for a hydraulic shop press, with 27 sleeves, an adapter, 6 centering pins, a case and gloves.

Pros

  • Made for a hydraulic shop press, the only kit here that states it
  • 27 sleeves with outside diameters from 39.5 to 92 mm
  • Adapter and 6 centering pins help line the sleeve up
  • Case and gloves in the box, with 24-hour service stated

Cons

  • Needs a hydraulic shop press, with no pulling spindles for hand work
  • Sleeve bores run 26 to 33 mm, a narrow band for larger bushings
  • No thrust bearings in the box
  • Suits cars and light commercial vehicles only
DAYUAN Universal Press Pull Sleeve Remove Install

DAYUAN Universal Press Pull Sleeve Remove Install

DAYUAN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 26-piece drop forged set with 20 sleeves from 34 to 72 mm, 4 pulling spindles with thrust bearings, and a 1 year warranty.

Pros

  • 20 sleeves from 34 to 72 mm inside diameter, in 2 mm steps
  • 4 pulling spindles in M10, M12, M14 and M16, with nuts and thrust bearings
  • Drop forged steel, heat treated for rugged jobs
  • Fits cars, light commercial and heavy goods vehicles

Cons

  • No storage case stated in the box
  • Outside diameters run 44 to 82 mm, narrower than the OMT kit
  • Spindles stop at M16, with no M18 size
  • Safety glasses and gloves are not in the box
28PCS ProfessionalPress & Pull Sleeve Kit

28PCS ProfessionalPress & Pull Sleeve Kit

WINMAX TOOLS AUTOMOTIVE9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 28-piece set with sleeves from 34 to 72 mm inside diameter, for bearings, bushes and seals on cars and light commercial vehicles.

Pros

  • Sleeves from 34 to 72 mm inside diameter in 2 mm steps
  • Covers silent bearings, hydraulic bearings, ball bearings, shaft seals and rubber bearings
  • Universal fit for cars and light commercial vehicles
  • Outside diameters run 44 to 82 mm for larger housings

Cons

  • No pulling spindles in the box
  • No steel grade stated
  • No storage case in the box
  • No weight stated

Spec sheet comparison

Model Gear Score Sleeves Spindles Material Case Warranty
Orion Motor Tech 27-Piece 9.6/10 22 5 Carbon steel Blow-molded case 1 year
KTPROT 34-Piece 9.5/10 27 Not stated Forged steel Case and gloves 1 year
DAYUAN 26-Piece 9.5/10 20 4 Drop forged steel Not stated 1 year
WINMAX 28-Piece 9.4/10 20 Not stated Not stated Not stated 1 year

Ratings in this table are the makers’ own claims taken from each product page (21 November 2026).

Buying guide: best shop press sleeve kit sizes and fit

Sleeve bore sizes and steps

Sleeve bore is the figure to match. The DAYUAN, OMT and WINMAX kits cover inside diameters from 34 mm, in 2 mm steps, to 72 mm or 80 mm, while the KTPROT kit lists 27 sleeves with outside diameters from 39.5 to 92 mm and bores from 26 to 33 mm. Measure the bushing or bearing outside diameter, then pick a sleeve with a bore that clears it and an outside diameter that seats in the housing. A kit that steps in 2 mm increments covers more sizes with fewer gaps.

Pulling spindles and threads

Spindles pull the sleeve through the housing, and the thread has to match the hardware on hand. The DAYUAN kit has 4 spindles in M10, M12, M14 and M16, with nuts and thrust bearings, and the OMT kit has 5 in M10, M12, M14, M16 and M18. The KTPROT kit has no pulling spindles; it has an adapter and 6 centering pins for use with a hydraulic shop press. The WINMAX kit states no spindles, so it suits a buyer who already owns them. Notched sleeves, on the OMT kit, catch the bushing edge and show its position while it moves.

Steel and build

Steel decides whether a sleeve holds its bore under press load. The DAYUAN set is drop forged steel, heat treated, and the OMT set is premium carbon steel with heat treated and blackened spindles. The KTPROT set is forged from high quality steel for high-strength pressure work. The WINMAX listing states no steel grade, so its build scores lowest here. A forged sleeve with a stated heat treatment is the safer pick for repeated pressing.

Cases, gloves and storage

A sleeve set is only useful if the sizes stay together. The OMT kit comes in a blow-molded case, and the KTPROT kit comes with a case and gloves. The DAYUAN and WINMAX listings state no case, so plan storage for 26 and 28 pieces. Gloves and a case matter more when the kit moves between home garage and workshop, which the OMT listing names as its use.

Using the kit with a shop press

Only the KTPROT kit states it is used with a hydraulic shop press. The rest are press and pull sleeve kits for removing and installing bearings, bushes and seals on cars and commercial vehicles. Set the sleeve square on the housing, center the spindle, and press in small moves while watching the bushing position. Wear safety glasses and gloves, as the DAYUAN listing notes, and keep hands clear of the ram.

Use as directed. Wear safety glasses and gloves when pressing, keep hands clear of the ram and the sleeve, and check the sleeve fit before applying force. Never exceed the rated capacity of the press you use. See the OSHA machine guarding page and our Safety Disclaimer.

Before You Strike an Arc

  • Measure the bushing or bearing outside diameter, then pick a sleeve with a bore that clears it; the kits step in 2 mm increments from 34 mm.
  • Match the pulling spindle thread to the hardware on hand: M10, M12, M14, M16, and M18 appear across these kits.
  • Count the kit on arrival: sleeves, spindles, adapter, centering pins, case, and gloves.
  • Wear safety glasses and gloves while pressing.
  • Use the notched sleeve edge to catch the bushing edge and watch the bushing position as it moves.

FAQ for welders

What is a shop press sleeve kit?

A sleeve kit is a set of steel sleeves and pulling spindles that press bearings, bushes and seals out of and into housings, using a hydraulic shop press. The sleeves come in stepped bores, and the spindle pulls the sleeve through the housing. The kits here cover cars and light commercial vehicles, with some also covering heavy goods vehicles.

What sleeve sizes do these kits cover?

The DAYUAN, OMT and WINMAX kits cover inside diameters from 34 mm, in 2 mm steps, to 72 mm or 80 mm. The KTPROT kit lists 27 sleeves with outside diameters from 39.5 to 92 mm and bores from 26 to 33 mm. Measure the bushing outside diameter, then match it to a sleeve bore.

What pulling spindle sizes come with these kits?

The DAYUAN kit has 4 pulling spindles in M10, M12, M14 and M16, and the OMT kit has 5 in M10, M12, M14, M16 and M18. The KTPROT kit has an adapter and 6 centering pins instead of pulling spindles, and the WINMAX listing states no spindles. Match the thread to the drivers and wrenches on hand.

Do these kits work with a hydraulic shop press?

The KTPROT kit states it is used with a hydraulic shop press. The rest are press and pull sleeve kits for removing and installing bearings, bushes and seals on cars and commercial vehicles. Check the sleeve bore and spindle thread against the job before pressing.

What warranty do these sleeve kits carry?

Each of the four kits here states a 1 year warranty. The DAYUAN, OMT, WINMAX and KTPROT listings all state the same term.

Related: best shop press, best 12 ton hydraulic press, best hydraulic press, and the lifting and pressing hub. Also see our shop press vs arbor press. Also see our how does a hydraulic press work. Also see our best air hydraulic press.

Scoring, line by line

Each kit is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Press sleeve kits have no electrical safety listing to state, so every kit here scores zero on that criterion; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Orion Motor Tech 27-Piece 9.6 32 22 22 0 2
KTPROT 34-Piece 9.5 30 21 21 0 2
DAYUAN 26-Piece 9.5 29 21 21 0 2
WINMAX 28-Piece 9.4 26 18 20 0 2

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

More buying guides