Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Induction Heater for Bolts (2026): 5 Picks for Rusted Fasteners

Five 110V induction heaters for rusted bolts, compared on power, coil count, heat time and cooling, and scored on what each listing states.

Best Induction Heater for Bolts (2026): 5 Picks for Rusted Fasteners
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1IrrDen 1800WTop PickIrrDen 1800W9.5/10View on Amazon
  2. 2Gereat 1500WBest Case KitGereat 1500W9.5/10View on Amazon
  3. 3Kinchoix 1300WHighest Stated TemperatureKinchoix 1300W9.4/10View on Amazon
  4. 4KAXORE 1500WSlimmest BodyKAXORE 1500W9.5/10View on Amazon

A rusted bolt on an exhaust flange or a suspension arm can eat a whole afternoon. Heat breaks the rust bond, but a torch brings open flame into a bay full of hoses, wiring and fuel lines. The best induction heater for bolts puts heat only into the fastener, with no flame and no sparks, and this guide compares the heaters on what each listing states: power, coil count, heat time and cooling.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Top Pick IrrDen 1800W: 1800W with 12 coils, a rotatable body and heat in 10 to 15 seconds. Check price on Amazon
  • Best Case Kit Gereat 1500W: 1500W with 10 copper coils and a fitted black aluminum case. Check price on Amazon
  • Highest Stated Temperature Kinchoix 1300W: 1300W with a stated max of 1472°F and a bendable 75cm DIY coil. Check price on Amazon
  • Slimmest Body KAXORE 1500W: 1500W in a 15.55 x 2.8 x 2.8 inch body with a flexible coil. Check price on Amazon

The machines

1800W Rotatable Magnetic Induction Heater Bolt

1800W Rotatable Magnetic Induction Heater Bolt

IrrDen9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 1800W heater with 12 coils, a rotatable body and heat in 10 to 15 seconds, the most complete kit here.

Pros

  • 1800W, the highest power here, with heat in 10 to 15 seconds
  • 12 coils, including 20mm, 30mm, 40mm and 50mm sizes, two 750mm straight DIY coils and two flat coils
  • Rotatable body for tight engine bays and exhaust work
  • Built-in temperature sensor, automatic cooling fan and overheat protection

Cons

  • 6.6 pounds to hold through a long job
  • Must not run over 2 minutes continuously
  • May not heat aluminum or copper effectively
  • No warranty term in the listing
Induction Heater 1500W 110V Bolt Removal Kit

Induction Heater 1500W 110V Bolt Removal Kit

Gereat9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1500W heater with 10 copper coils, a pistol grip and a fitted aluminum case, with heat in 25 seconds.

Pros

  • 1500W at 110V with heat in 25 seconds
  • 10 thickened pure copper coils in different sizes
  • Non-slip pistol grip with built-in fan cooling
  • Black aluminum case with shockproof foam lining

Cons

  • 25 second heat is slower than the 10 to 15 seconds the IrrDen states
  • No flexible or DIY coil for tight spaces
  • No LED light for low-light work
  • No warranty term in the listing
Induction Heater Bolt Removal

Induction Heater Bolt Removal

KAXORE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A slim 1500W heater with 8 coils, including a flexible coil, and heat in 25 seconds.

Pros

  • 1500W at 110V with heat in 25 seconds
  • 8 coils: 7 preformed and 1 flexible coil for tight areas
  • Slim 15.55 x 2.8 x 2.8 inch body
  • Overheat indicator and built-in cooling system

Cons

  • 8 coils is fewer than the 10 and 12 coil kits here
  • 25 second heat is slower than the 10 to 15 seconds the IrrDen states
  • No storage case in the box
  • No LED light for low-light work
Induction Heater Bolt Removal 1300W 110V

Induction Heater Bolt Removal 1300W 110V

Kinchoix9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1300W heater with a stated max of 1472°F, 5 copper coils including a bendable DIY coil.

Pros

  • Max working temperature of 1472°F (800°C) stated
  • 5 coils including a 75cm malleable DIY coil for tight spaces
  • 99.9% oxygen-free copper coils
  • Flameless heat with no sparks, plus overheat protection and a cooling fan

Cons

  • 1300W is the lowest stated power here
  • 5 coils is the fewest here
  • DIY coil needs a minimum of 3 winding circles to work
  • Heats ferrous metals and some stainless steel only
Solary Induction Heater for Bolt Removal

Solary Induction Heater for Bolt Removal

Solary9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-coil heater with a built-in LED light and a toolbox, with heat in 15 seconds per the listing.

Pros

  • Heat in 15 seconds, per the listing
  • 10 coils in different sizes with a toolbox for storage
  • Built-in LED light with a white to yellow overheat indicator
  • Cooling fan and overheat protection

Cons

  • Widest body here at 9.84 inches
  • No flexible or DIY coil among the 10 coils
  • No rotatable body for tight engine bays
  • Stores in a toolbox rather than a fitted case

Other welders and gear to compare

Best induction heater for bolts compared

Model Power Coils Heat time Voltage Dimensions
IrrDen 1800W 1800W 12 10 to 15 seconds 110 to 120V 18.0 x 4.0 x 4.0 in
Gereat 1500W 1500W 10 25 seconds 110V 17.0 x 6.0 x 5.0 in
KAXORE 1500W 1500W 8 25 seconds 110V 15.55 x 2.8 x 2.8 in
Kinchoix 1300W 1300W 5 5 to 25 seconds 110V 17.72 x 8.27 x 5.12 in
Solary 10 Coil Not stated 10 15 seconds Not stated 17.52 x 9.84 x 4.53 in

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 15 November 2026.

Buying guide: what matters for rusted bolts

Power

Stated power here runs from 1300W to 1800W. The IrrDen states 1800W, the Gereat and the KAXORE state 1500W, and the Kinchoix states 1300W. The Solary states no wattage, so compare it on coil count and heat time instead.

Coil count and fit

Coil count runs from 5 to 12. The IrrDen includes 12 coils, with 20mm, 30mm, 40mm and 50mm sizes, two 750mm straight DIY coils and two flat coils. The Gereat and the Solary include 10 coils each, the KAXORE includes 8, with 7 preformed and 1 flexible, and the Kinchoix includes 5, with 4 standard coils and 1 75cm DIY coil. Pick the coil that fits around the nut, and check the fit before heating.

Heat time and temperature

Stated heat times run from 5 to 25 seconds. The Kinchoix states 5 to 25 seconds, depending on bolt size, and a max working temperature of 1472°F (800°C). The IrrDen states 10 to 15 seconds, with a recommended heating temperature of 300 to 500°C and a limit of 550°C. The Solary states 15 seconds, and the Gereat and the KAXORE state 25 seconds. Heat time depends on bolt size, per the Kinchoix listing, so a large nut takes longer than a small one.

Cooling and overheat protection

Every heater here states a cooling fan and overheat protection. The Solary and the Kinchoix change an indicator light from white to yellow in overheat mode. The IrrDen states a built-in temperature sensor and an automatic cooling fan, and warns not to run over 2 minutes continuously. Let the unit and the coil cool between jobs.

Power supply

Every heater here states 110V, and the IrrDen states 110 to 120V with a 50/60Hz power setup. Check that the outlet matches the stated voltage before plugging in.

Use as directed. Induction heat stays in the metal, but the fastener itself gets hot enough to burn. Keep the coil around the nut without touching the metal workpiece, keep hands clear while the coil is powered, and let the fastener cool before handling it. Work with ventilation and keep flammable material away from hot metal.

Before You Strike an Arc

  • Plug into a 110V supply; the IrrDen also states 110 to 120V and 50/60Hz.
  • Fit the coil around the nut without touching the metal, and check the coil insulation for bends or damage before switching on.
  • Do not run the IrrDen over 2 minutes continuously; let the unit and coil cool between jobs.
  • Check that the coil size matches the nut, and keep paint, rubber, wiring and hoses clear of the hot fastener.

FAQ for welders

Will an induction heater loosen a rusted bolt?

Yes, if the fastener is ferrous metal. Induction heat goes into the fastener and breaks the rust bond, and the listings here state heat times from 5 to 25 seconds. The IrrDen listing notes that aluminum and copper may not heat effectively, so check the fastener material before heating.

How long does it take to heat a bolt?

It depends on bolt size. The Kinchoix states 5 to 25 seconds, the IrrDen states 10 to 15 seconds, the Solary states 15 seconds, and the Gereat and the KAXORE state 25 seconds. Larger fasteners take longer, per the Kinchoix listing.

What size coil do I need?

Use a coil that fits around the nut. The IrrDen kit includes 20mm, 30mm, 40mm and 50mm coils, plus two 750mm straight DIY coils and two flat coils. The Kinchoix includes a 75cm DIY coil that bends to fit tight spaces, with a minimum of 3 winding circles.

Can I use an induction heater near paint and wiring?

The heat stays in the fastener, so paint, rubber and plastic nearby are not heated the same way. The Gereat, Kinchoix and KAXORE listings all state that nearby plastic, rubber and wiring are protected. Still keep the coil off the workpiece and clear of hoses and wiring.

What power supply does an induction heater need?

Every heater here states 110V, and the IrrDen states 110 to 120V with a 50/60Hz setup. Plug into an outlet that matches the stated voltage.

Related: best handheld induction heater, best induction heater large, best bolt extractor set, best spray on rust remover, and the metal fab tools hub.

Scoring, line by line

Each heater is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No listing here states a safety standard or a warranty term, so safety and warranty add nothing to any score here; the ranking comes from the other three.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
IrrDen 1800W 9.5 32 21 21 0 0
Gereat 1500W 9.5 30 21 21 0 0
KAXORE 1500W 9.5 29 20 21 0 0
Kinchoix 1300W 9.4 28 20 20 0 0
Solary 10 Coil 9.4 26 19 20 0 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.

More buying guides