Best Induction Heaters for Welding (2026)
Four induction heaters for freeing seized bolts and fasteners, compared by power, coils, heating speed and cooling protection.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallAFKLLA 12-Coil9.6/10View on Amazon - 2
Best 8-Coil KitHarsire 1500W 8-Coil9.6/10View on Amazon - 3
Best Small KitHarsire 1300W 4-Coil9.5/10View on Amazon - 4
Best Handheld PickEMAGIH SE-1300W9.5/10View on Amazon
A seized bolt can stop a welding repair cold: the part cannot come off, the joint cannot be cleaned, and the torch you would rather not use sits too close to wiring and paint. The best induction heaters for welding shops solve that one job, heating the fastener itself with no open flame, so the repair can move on to fit-up and welding. We compared four coil kits on what each listing states: power, coil count, heating time, cooling protection and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall AFKLLA 12-Coil: 12 coils, 25 second heating, LED light, toolbox and smart cooling Check price on Amazon
- Best 8-Coil Kit Harsire 1500W 8-Coil: 1500W, 8 coils, 25 second heating and sensor driven cooling fans Check price on Amazon
- Best Small Kit Harsire 1300W 4-Coil: 1300W, 4 bendable coils, LED light and cooling fan Check price on Amazon
- Best Handheld Pick EMAGIH SE-1300W: Handheld at 2.65 pounds, with overheat protection device Check price on Amazon
The machines

Induction Heater Bolt Removal
A 1500W induction heater kit with 12 coils, a toolbox and an LED light for freeing seized bolts and nuts.
Pros
- 12 coils: 10 fixed coils and 2 DIY coils
- Heats rusted screws and nuts in 25 seconds, per the listing
- Built-in LED light illuminates dark workspaces
- Fan and smart cooling system give overheat protection
Cons
- No warranty term is stated
- Listing does not state which metals it will not heat
- Coil sizes for the fixed coils are not fully stated
- 1500W power needs a suitable mains supply

1500W Magnetic Induction Heater Tool
A 1500W induction heater with 8 coils and sensor driven cooling for stubborn, rusted bolts.
Pros
- 8 coils including 25, 30 and 45 mm sizes plus DIY coils
- Heats rusted bolts in 25 seconds, per the listing
- Temperature sensors engage cooling fans when needed
- Heats with no open flames and no sparks, per the listing
Cons
- No warranty term is stated
- No voltage is stated in the listing
- No coil count beyond 8 is broken down by fixed size
- Listing leans on automotive and farm examples over welding

Upgrated Magnetic Induction Heater Kit
A handheld 1300W induction heater with 4 bendable coils, an LED light and a cooling fan.
Pros
- 4 coils that can be bent to meet the work
- Heats in 25 seconds, per the listing
- LED light at the end of the tool for dark work
- Cooling fan and overheating protection device stated
Cons
- No warranty term is stated
- Listing does not state which metals it will not heat
- Fewest stated uses beyond nuts, screws, gears and bearings
- Fan runs only when power is connected, per the listing
Pros
- Handheld form suits tight spots, per the listing
- Handheld at 2.65 pounds, per the spec table
- Overheat protection device is stated
- Suits rust removal, paint coating removal and small heat treatment
Cons
- Listing states it cannot heat copper and aluminum
- Power naming is contradictory: named 1000W but actual 1300W to 1400W
- Heating usually stops after 2 to 3 minutes, per the listing
- Only 3 coils, the fewest in this group
Other welders and gear to compare
U.S. Solid 15KW High Frequency Induction Heater FurnaceCheck price on Amazon
TOOLGUY REPUBLIC 36" Free Forming Induction Heater CoilCheck price on Amazon
Solary Automotive Magnetic Induction HeaterCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Power | Coils | Heating time | Warranty |
|---|---|---|---|---|---|
| AFKLLA 12-Coil | 9.6/10 | 1500W | 12 | 25 seconds | Not stated |
| Harsire 1500W 8-Coil | 9.6/10 | 1500W | 8 | 25 seconds | Not stated |
| Harsire 1300W 4-Coil | 9.5/10 | 1300W | 4 | 25 seconds | Not stated |
| EMAGIH SE-1300W | 9.5/10 | 1300W | 3 | Not stated | Not stated |
All specs here repeat what the maker rates and the listing prints, copied down 30 October 2026.
Buying guide: best induction heaters for welding
Power and coil count
Two listings here state 1500W and two state 1300W, and coil count runs from 3 to 12 across the group. The AFKLLA kit leads on count with 10 fixed coils plus 2 DIY coils, while the Harsire 1500W kit states 8 coils in 25, 30 and 45 mm sizes plus DIY coils. More coils matter when fasteners vary in size, since a coil that fits the nut heats it evenly and a coil that does not fit wastes the field. Check the coil sizes on the listing against the fasteners you actually free, not just the total count.
Heating time and cooling stops
Three listings state heating in 25 seconds for rusted screws and nuts: the AFKLLA kit, the Harsire 1500W kit and the Harsire 1300W kit. The EMAGIH listing states no heating time, and instead states that heating usually stops after 2 to 3 minutes because of its overheat protection device. That stop is a cooling limit, and it changes how you plan a run of fasteners: work through one stuck bolt at a time, and let the tool cool between jobs. The Harsire 1500W listing describes the fullest cooling setup, with temperature sensors that engage cooling fans when needed.
Metal limits to check before you buy
Only the EMAGIH listing addresses metals the tool will not heat, and it states plainly that the machine cannot heat copper and aluminum. The other three listings describe heating steel fasteners, nuts, screws, gears, pulleys and bearings, but do not state behavior on copper or aluminum. For a welding shop that works aluminum parts, that gap matters: do not assume a heater that frees steel bolts will heat an aluminum fitting. Read the listing for the metal you plan to heat, and treat anything not stated as not stated.
Kit, light and storage
A kit that lives in a box gets used more than coils loose in a drawer. The AFKLLA listing includes a durable toolbox for the heater and coils, and the Harsire 1300W listing includes a box as well. Both the AFKLLA and Harsire 1300W listings state an LED light on the tool for dark workspaces, which helps under a vehicle or inside a frame. The EMAGIH listing states the lightest build here at 2.65 pounds, which suits handheld work overhead or in tight spots.
Before You Strike an Arc
- Check voltage on the listing: three listings state 110V, while the Harsire 1500W listing does not state voltage.
- Match coil size to the fastener before heating, using the stated 25, 30 and 45 mm sizes on the Harsire 1500W kit or the DIY coils where the listing provides them.
- Plan for cooling stops: the EMAGIH listing states heating usually stops after 2 to 3 minutes.
- Check the listing for a warranty term: no listing here states a concrete term.
- Remember these tools heat with no open flames, per the listings, but the fastener itself gets hot, so let it cool before handling.
FAQ for welders
Can an induction heater free a rusted bolt before a welding repair?
Yes, that is the job these listings describe: heating a seized fastener so it expands and loosens without thread damage. Three listings state heating in 25 seconds for rusted screws and nuts. The EMAGIH listing states no heating time, so plan extra time with that kit.
Will these heaters work on aluminum or copper?
The EMAGIH listing states its machine cannot heat copper and aluminum, so do not buy that kit for those metals. The other three listings do not state behavior on copper or aluminum, and they describe steel fasteners, nuts, screws, gears, pulleys and bearings. Check the listing for your metal before ordering.
What power supply do these heaters need?
Three listings state 110V: the AFKLLA kit, the EMAGIH kit and the Harsire 1300W kit. The Harsire 1500W listing does not state voltage, so confirm the supply on that listing before buying. None of these listings describe battery power, so plan for a mains outlet in the shop.
Does any listing state a warranty?
No listing here states a concrete warranty term, so every pick scores zero on warranty in this guide. Check the listing before buying if a warranty term matters to you, since the listings here do not give one you can compare.
Related: metal fab tools, best induction heater for pipe, best handheld induction heater, and best welding ground clamp.
Scoring, line by line
Each heater is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. All four listings state overheat protection of some kind, so every pick scores on safety, while no listing states a concrete warranty term, so every pick scores zero on warranty. The ranking turns on coil range, heating speed and the completeness of the listing.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| AFKLLA 12-Coil | 9.6 | 32 | 21 | 21 | 7 | 0 |
| Harsire 1500W 8-Coil | 9.6 | 30 | 20 | 20 | 8 | 0 |
| Harsire 1300W 4-Coil | 9.5 | 28 | 20 | 20 | 7 | 0 |
| EMAGIH SE-1300W | 9.5 | 26 | 19 | 19 | 7 | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.




