Best Hard Hat for Welders (2026)
Five hard hats for welders compared by shell, suspension, standard, heat rating, and warranty, with phenolic, fiberglass, and thermoplastic picks.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMSA 816651 Skullgard9.7/10View on Amazon - 2
Best FiberglassFibre-Metal P2A Super Eight9.7/10View on Amazon - 3
Best PhenolicMSA 475395 Skullgard9.7/10View on Amazon - 4
Best Full BrimMootycapa Fiberglass Hard Hat9.4/10View on Amazon - 5
Best ThermoplasticFibre-Metal E2 Super Eight9.4/10View on Amazon
A bead runs hot, sparks fall, and the hard hat has to stay put while the hood comes down. The best hard hat for welders is one with a smooth crown that clears welding equipment, a suspension that fits, and a stated standard for top impact. This guide compares the hard hats in this group by shell, suspension, standard, heat rating, and warranty, using only what each maker publishes.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall MSA 816651 Skullgard: Smooth crown for welding equipment, Fas-Trac III, ANSI Type I Class G. Check price on Amazon
- Best Fiberglass Fibre-Metal P2A Super Eight: Fiberglass shell, ANSI and CSA Type 1 Class G, 2 year warranty. Check price on Amazon
- Best Phenolic MSA 475395 Skullgard: Phenolic shell, Fas-Trac III, ANSI Type I Class G, 1 year warranty. Check price on Amazon
- Best Full Brim Mootycapa Fiberglass Hard Hat: Full brim fiberglass shell, 6-point suspension, 350F radiant heat. Check price on Amazon
- Best Thermoplastic Fibre-Metal E2 Super Eight: Thermoplastic cap, SuperEight suspension, head sizes 6.75 to 8 inch. Check price on Amazon
The machines

MSA 816651 Skullgard Cap Style Safety Hard Hat
A phenolic Skullgard cap with Fas-Trac III suspension, a smooth crown for welding equipment, and ANSI Type I Class G certification.
Pros
- Smooth crown allows the easiest use of MSA welding equipment
- Fas-Trac III suspension with three levels of nape strap adjustment
- Rated for radiant heat loads up to 350F
- Meets ANSI/ISEA Z89.1-2014 Type I Class G, SEI certified
Cons
- Standard size only, with no other size stated
- Non-slotted cap, with no accessory slots stated
- Heavier than the Fibre-Metal P2A at 0.97 lb
- Natural tan only in this listing

Fibre-Metal by Honeywell P2AQRW01A000 Super Eight
A fiberglass Super Eight hard hat with ANSI and CSA Type 1 Class G ratings and a 2 year manufacturer warranty.
Pros
- Injection-molded fiberglass compound with crack resistance
- SuperEight suspension spreads weight over a wide area
- Meets ANSI Z89.1-2014 Type 1 Class G and CSA Z94.1-2015
- 2 year manufacturer warranty is the longest stated here
Cons
- No heat rating is stated for this hat
- No electrical rating is stated for this hat
- White only in this listing
- Medium size only in this listing

MSA 475395 Skullgard Cap Style Safety Hard Hat
A phenolic Skullgard cap with Fas-Trac III suspension, radiant heat loads up to 350F, and ANSI Type I Class G certification.
Pros
- Phenolic shell crafted by hand for durability
- Fas-Trac III suspension with flush rear lug attachments
- Rated for radiant heat loads up to 350F
- Meets ANSI/ISEA Z89.1-2014 Type I Class G, SEI certified
Cons
- Standard size only, with no other size stated
- Non-slotted cap, with no accessory slots stated
- Heavier than the MSA 816651 at 1.12 lb
- Natural tan only in this listing

Mootycapa Cap Style Fiberglass Hard Hat with Brim
A full brim fiberglass hard hat with a 6-point suspension, radiant heat loads up to 350F, and electrical protection up to 2200V.
Pros
- Full brim fiberglass shell with impact resistance
- 6-point suspension with removable padded sweatband
- Rated for radiant heat loads up to 350F
- Protection against electrical hazards up to 2200V
Cons
- No warranty term is stated
- No ANSI or CSA standard is stated
- Heaviest hat here at 1.49 lb
- Brown only in this listing

Fibre-Metal by Honeywell E2QRW11A000 Super Eight
A thermoplastic Super Eight hard hat with eight load bearing points and head sizes from 6.75 to 8 inch.
Pros
- SuperEight suspension with eight load bearing points
- Thermoplastic cap with smooth crown design
- Fits head sizes 6.75 to 8 inch
- Non-slip and non-strip ratchet headgear
Cons
- No warranty term is stated
- No ANSI or CSA standard is stated
- No heat rating is stated for this hat
- Black only in this listing
Other welders and gear to compare
Pyramex Ridgeline Full Brim Hard Hat 4 Point Ratchet MatteCheck price on Amazon
PYRAMEX Ridgeline Cap Style Hard HatCheck price on Amazon
Fullsheild Reversible Welding Cap FR Cotton Welder HatCheck price on Amazon
Fullsheild Reversible Welding Cap FR Cotton WelderCheck price on Amazon
Fibre-Metal by Honeywell Speedy Loop Hard Hat Mounting SystemCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Shell | Suspension | Standard | Warranty |
|---|---|---|---|---|---|
| MSA 816651 Skullgard | 9.7/10 | Phenolic resin | Fas-Trac III ratchet | ANSI Z89.1-2014 Type I Class G | 1 year warranty |
| Fibre-Metal P2A Super Eight | 9.7/10 | Fiberglass | SuperEight ratchet | ANSI Z89.1-2014 Type 1 Class G | 2 year manufacturer |
| MSA 475395 Skullgard | 9.7/10 | Phenolic resin | Fas-Trac III ratchet | ANSI Z89.1-2014 Type I Class G | 1 year warranty |
| Mootycapa Fiberglass Hard Hat | 9.4/10 | Fiberglass | 6-point suspension | Not stated | Not stated |
| Fibre-Metal E2 Super Eight | 9.4/10 | Thermoplastic | SuperEight ratchet | Not stated | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (18 November 2026). Three of the five state a warranty term; three state an ANSI standard.
Buying guide: choosing the best hard hat for welders
Shell material
Shell material sets the character of the hat. The two MSA Skullgard hats use a phenolic shell, crafted by hand, and the Mootycapa and the Fibre-Metal P2A use fiberglass. The Fibre-Metal E2 uses a thermoplastic cap with the Fibre-Metal smooth crown design. Phenolic and fiberglass shells suit hot work and sparks, while a thermoplastic cap suits a shop where the hat sees general use. Match the shell to the work: a phenolic Skullgard suits steel mills, welding, construction, open-pit mining, and oil and gas work, and the Mootycapa suits construction, oil and gas, mining, welding, foundry, fabrication, and electrical work.
Suspension and fit
Suspension decides whether the hat stays comfortable through a shift. Both MSA hats use the Fas-Trac III ratchet suspension, with flush rear lug attachments that remove pressure points, and the 816651 adds three levels of nape strap adjustment and a ratchet comfort pad contoured to the back of the head. The Mootycapa uses a 6-point suspension with a removable padded sweatband, a soft top pad, and an oversized ratchet adjustment dial that is easy to grip with gloves on. Both Fibre-Metal hats use the SuperEight suspension, with eight load bearing points that balance and spread weight over a wide area. The E2 fits head sizes 6.75 to 8 inch, or 54 cm to 65 cm. Try the ratchet adjustment with gloves on before the first weld, and check the nape strap setting on the MSA hats.
Heat and electrical ratings
Heat ratings differ across the group, and only two hats state one. Both MSA hats are stated for radiant heat loads up to 350F, and the Mootycapa resists radiant heat loads up to 350 degrees F and offers protection against electrical hazards up to 2200V. The Fibre-Metal hats state no heat rating and no electrical rating, so the group cannot be compared on those points. Do not call a hat better on heat or electrical rating unless the listing states the figure; an unstated figure is a gap in the listing, not a win for the other side. A welder who works near high heat should pick from the hats that state a heat rating.
The standard on the shell
Three hats state an ANSI standard, and one states a CSA standard as well. The MSA Skullgard caps meet the requirements for a Type I top impact helmet as outlined in ANSI/ISEA Z89.1-2014 Class G, and they are SEI certified. The Fibre-Metal P2A meets ANSI Z89.1-2014 Type 1 Class G, including the Quick-Lok model, and CSA Z94.1-2015 Type 1 Class G or C, with Class C for the Quick-Lok model, in both forward and reverse donning. The MSA 816651 also meets the voluntary standard for reverse donning, low temperature, higher temperature, and Hi-Viz. The Mootycapa and the Fibre-Metal E2 state no standard. Check the standard on the shell against the rules for your site before you buy, and see our welding helmet types guide for the hood side of the setup.
Cap style or full brim
Four hats here are cap style, and one is full brim. The Mootycapa is a full brim hard hat, and its full brim strip protects against accidental brim collisions. The MSA hats are non-slotted caps, and the Fibre-Metal hats are cap style with a smooth crown. A smooth crown matters for welding: the MSA 816651 states that a smooth crown allows for the easiest use of all MSA welding equipment. A full brim shades the neck and shoulders, while a cap style stays closer to the head. The welding cap vs hard hat guide compares caps and hats for shop work.
Use as directed. Wear the hard hat with the suspension adjusted and the shell seated on the head, and keep the area under and around the work clear of anything that can burn, since spatter and slag fall. Check the shell and suspension on arrival, and follow the manual for care and replacement.
Before You Strike an Arc
- Check the suspension before the first weld: Fas-Trac III ratchet on the MSA hats, 6-point suspension on the Mootycapa, and SuperEight suspension on the Fibre-Metal hats.
- Check the crown is smooth for welding equipment, as stated for the MSA 816651 Skullgard.
- Check the head size against the E2, which fits head sizes 6.75 to 8 inch.
- Check the standard on the shell: ANSI Z89.1-2014 Type I Class G on the MSA hats and the Fibre-Metal P2A.
- Check the shell and suspension on arrival, and follow the manual for care.
FAQ for welders
Which hard hat here is made for welding equipment?
The MSA 816651 Skullgard. Its smooth crown allows for the easiest use of all MSA welding equipment, and it meets ANSI/ISEA Z89.1-2014 Type I Class G with SEI certification. The MSA 475395 is the same phenolic Skullgard shell with the Fas-Trac III suspension, and it also states a 350F radiant heat rating.
What standard do the MSA hard hats meet?
Both MSA Skullgard caps meet the requirements for a Type I top impact helmet as outlined in ANSI/ISEA Z89.1-2014 Class G, and they are SEI certified. The 816651 also meets the voluntary standard for reverse donning, low temperature, higher temperature, and Hi-Viz.
Which hard hats state a warranty term?
Both MSA hats fall under the standard 1 year warranty, and the Fibre-Metal P2A states a 2 year manufacturer warranty. The Mootycapa and the Fibre-Metal E2 state no warranty term.
Does any hard hat here state an electrical rating?
The Mootycapa states protection against electrical hazards up to 2200V, along with a radiant heat rating up to 350 degrees F. The other four hats state no electrical rating, so they cannot be compared on that point.
Cap style or full brim for welding?
Four hats here are cap style, and the Mootycapa is full brim. A cap style stays closer to the head, and a smooth crown clears welding equipment, as stated for the MSA 816651. A full brim shades the neck and shoulders, and the Mootycapa states that its full brim strip protects against accidental brim collisions.
Related: best ear muffs for hard hat, welding safety gear checklist for beginners, welding safety gear, and welding helmet types.
Scoring, line by line
Each hard hat is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. For a hard hat, safety means a stated ANSI or CSA standard; the two MSA Skullgard hats state ANSI/ISEA Z89.1-2014 Type I Class G with SEI certification, and the Fibre-Metal P2A states ANSI Z89.1-2014 Type 1 Class G and CSA Z94.1-2015 Type 1 Class G. The Mootycapa and the Fibre-Metal E2 state no standard, so they score zero on that line. Three state a warranty term: both MSA hats at 1 year and the Fibre-Metal P2A at 2 year manufacturer.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| MSA 816651 Skullgard | 9.7 | 32 | 22 | 21 | 9 | 3 |
| Fibre-Metal P2A Super Eight | 9.7 | 29 | 21 | 20 | 9 | 3 |
| MSA 475395 Skullgard | 9.7 | 30 | 21 | 21 | 9 | 3 |
| Mootycapa Fiberglass Hard Hat | 9.4 | 28 | 21 | 20 | 0 | 0 |
| Fibre-Metal E2 Super Eight | 9.4 | 27 | 20 | 20 | 0 | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.




