Best Drill Press Locking Clamp (2026)
Five drill press locking clamps for drill press tables, compared on jaw opening, throat depth, materials and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallWEN 429DPC9.6/10View on Amazon - 2
Best Crank ClampStrong Hand PTTD6349.6/10View on Amazon - 3
Best 2-Pack ValueElsjoy 2-Pack9.6/10View on Amazon - 4
Second 2-PackQWORK 2-Pack9.6/10View on Amazon
The bit is about to break through and the workpiece starts to walk, or the small bracket you are drilling spins and ruins the hole. A locking clamp pinned to the drill press table holds the work still so both hands stay on the feed. This roundup compares five best drill press locking clamp picks on what each listing states: jaw opening, throat depth, materials and warranty. A good clamp seats flat, grips hard, and releases with one hand when the hole is done.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall WEN 429DPC: 3-1/2 inch capacity with a 3 inch throat, quick release lever, and the only 2 year warranty here. Check price on Amazon
- Best Crank Clamp Strong Hand PTTD634: Crank-handle hold-down with 3.4 inch throat and 3.3 inch capacity in high carbon steel. Check price on Amazon
- Best 2-Pack Value Elsjoy 2-Pack: Two 9 inch clamps with T-slot bases and titanium-coated 1045 steel. Check price on Amazon
- Second 2-Pack QWORK 2-Pack: Two 9 inch locking clamps in titanium-plated 1045 steel with 2 inch jaws. Check price on Amazon
The machines

WEN 429DPC Drill Press Clamp, 9"
A 9 inch drill press clamp with 3-1/2 inch board capacity, 3 inch throat and quick release lever, carrying the only 2 year warranty here.
Pros
- Clamps boards up to 3-1/2 inches thick
- 3 inch throat depth
- Quick release lever for simple disengagement
- 2 year manufacturer warranty stated
Cons
- Material listed only as ‘Metal’
- No throat reach beyond 3 inches
- Tension knob adds a setup step
- No safety standard stated

Strong Hand Tools PTTD634 Drill Press Clamp
A crank-handle drill press hold-down clamp in high carbon steel with 3.4 inch throat and 3.3 inch capacity, mounting on surfaces up to 1 inch thick.
Pros
- Crank handle for extra torque
- 3.4 inch throat, 3.3 inch capacity
- Mounts on surfaces up to 1 inch thick
- High carbon steel, 1000 psi tensile stated
Cons
- No warranty stated
- 1.9 lb is the heaviest single clamp here
- Stud and knob add mounting hardware to track
- No safety standard stated

Elsjoy 2 Pack 9 inch Drill Press Clamp
Two 9 inch drill press locking clamps in titanium-coated carbon steel with T-slot bases, 2 inch jaws and 3 inch throats.
Pros
- Two clamps in the pack
- T-slot base for tool-free positioning
- 1045 steel with titanium coating, pre-oiled
- Quick-release tab for one-touch opening
Cons
- No warranty stated
- 2 inch jaw is the smallest opening here
- No safety standard stated
- Workflow assumes standard T-slots

QWORK 9inch Drill Press Locking Clamp, 2 Pack
Two 9 inch drill press locking clamps in titanium-plated 1045 steel with 2 inch jaws and 3 inch throats.
Pros
- Two clamps in the pack
- 1045 steel with titanium plating
- Ergonomic handle per the maker
- Fastens to drill press slots
Cons
- No warranty stated
- 2 inch jaw is the smallest opening here
- No safety standard stated
- Listing leans woodworking

9-Inch Drill Press Locking Clamp and Vice
A 9 inch drill press locking clamp with 2 inch jaw opening and 3 inch throat that fastens to the drill press slot.
Pros
- Fastens directly to the drill press slot
- 2 inch jaw opening, 3 inch throat
- Quick release lever
- Simple single-clamp design
Cons
- No warranty stated
- No safety standard stated
- Thin listing with five short bullets
Other welders and gear to compare
WEN 426DPC Drill Press ClampCheck price on Amazon
WEN 430DPC Drill Press ClampCheck price on Amazon
2 PCS 9 Inch Drill Press Locking ClampCheck price on Amazon
POWERTEC 4PK Toggle ClampCheck price on Amazon
10 Pack Toggle ClampsCheck price on Amazon
Spec sheet comparison
| Clamp | Gear Score | Jaw/Capacity | Throat | Material | Weight | Warranty |
|---|---|---|---|---|---|---|
| WEN 429DPC | 9.6/10 | 3-1/2 in thick boards | 3 in | Metal | 16 ounces | 2 years |
| Strong Hand PTTD634 | 9.6/10 | 3.3 in | 3.4 in | High carbon steel | 1.9 lb | Not stated |
| Elsjoy 2-Pack | 9.6/10 | 2 in jaw | 3 in | Carbon steel, titanium coating | 1.08 kg | Not stated |
| QWORK 2-Pack | 9.6/10 | 2 in jaw | 3 in | 1045 steel, titanium | 1.11 kg | Not stated |
| GOSWIFT 9-Inch | 9.4/10 | 2 in jaw | 3 in | Not stated | Not stated | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (22 October 2026).
Best drill press locking clamp: buying guide
Hold-down vs locking pliers
Two styles show up here. The Strong Hand is a hold-down clamp: a crank handle drives the jaw down onto the work, and a stud mounts it to surfaces up to 1 inch thick. The other four are locking pliers style: squeeze the handles, the jaws lock, and a quick release lever drops them. The hold-down suits repetitive production clamping on the table; the locking style is faster to reposition, and each 2-pack includes two clamps.
Jaw opening and throat
Opening decides what fits under the jaw; throat decides how far in from the edge you can reach. The WEN opens to 3-1/2 inches of board with a 3 inch throat, the widest opening here. The Strong Hand offers 3.3 inch capacity with a 3.4 inch throat, the deepest reach. The other three all state a 2 inch jaw and 3 inch throat. Match both numbers to your work: a deep throat with a small opening still cannot swallow thick stock.
Mounting to the table
A clamp that cannot fasten to the table is just a paperweight with jaws. The WEN, GOSWIFT and QWORK fasten to drill press table slots, and the Elsjoy base slides into standard T-slots with a D-ring nut. The Strong Hand mounts with a 1/2-13 by 1.5 inch stud on surfaces up to 1 inch thick. Check your table slot size before you buy, since none of these listings states the slot width it fits.
Materials
Steel grades separate the listings that state them from the ones that do not. The Strong Hand states high carbon steel with 1000 psi tensile, the QWORK and Elsjoy state 1045 steel with titanium plating or coating, and the WEN and GOSWIFT state no grade at all. Titanium plating resists corrosion in a humid shop, and a stated grade tells you the maker is not hiding thin metal. Treat an unstated material as a gap, not a neutral. The GOSWIFT lists no material at all, which leaves its build a guess.
Warranty
Only the WEN states a warranty, 2 years, which is why it leads this ranking despite a thinner listing than the Strong Hand. The other four state nothing. A clamp is a simple tool, but the warranty still signals which maker will answer the phone when a spring goes soft. When two clamps fit your table equally, the stated warranty breaks the tie.
Use as directed. Clamp the work before the bit touches it, keep hands clear of the chuck and the work, and wear eye protection. Do not hold small parts by hand on a drill press, and keep the table slots clear of chips so the clamp seats flat. See the OSHA welding overview and our Safety Disclaimer.
Before You Strike an Arc
- Opening: match the jaw to your stock; the WEN takes boards up to 3-1/2 inches while the 2-packs top out at a 2 inch jaw.
- Mounting: check your table slot against the clamp base; the Elsjoy wants standard T-slots and the Strong Hand needs a surface up to 1 inch thick for its stud.
- Throat: the Strong Hand reaches 3.4 inches in from the edge, the deepest here, so plan your hole layout around the clamp, not the other way.
- On arrival: work the quick release a few times and check the jaws meet square before the first hole.
FAQ for welders
What is a drill press locking clamp?
It is a clamp that locks your workpiece to the drill press table so it cannot spin or walk while you drill. Locking pliers style clamps squeeze shut and hold, while hold-down styles like the Strong Hand drive a jaw down with a crank handle.
How do these fasten to the table?
Most fasten to the slots in the drill press table: the WEN, GOSWIFT and QWORK listings describe slot mounting, and the Elsjoy base slides into T-slots. The Strong Hand mounts with a stud on surfaces up to 1 inch thick. None of the listings states the slot width it fits, so check your table first.
What jaw opening do I need?
Enough to swallow your thickest common stock. The WEN opens to 3-1/2 inch boards, the Strong Hand to 3.3 inches, and the other three to a 2 inch jaw. If you drill mostly thin brackets, 2 inches is plenty; for thick blocks, buy the opening.
Can I use these on a welding table?
The Elsjoy listing names welding tables among its uses, and its T-slot base suits slotted tables. The others are sold for drill press slots, so check that the base fits your table before assuming it will.
Do I need two clamps?
One clamp stops spinning; two stop rocking. The QWORK and Elsjoy listings sell 2-packs, which suits long parts that need a clamp at each end. For small brackets a single clamp is enough.
Related: best tap wrench adjustable, best grinding wheel adapters, best sanding drum kit, best welding plug adapter, best cold chisel for metal, best round wire brush, best mini tube cutter, step drill bit vs twist drill bit, and the metal fab tools hub.
Scoring, line by line
Each clamp is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Only the WEN listing states a warranty, and none states a safety standard, so the ranking comes from opening, throat, materials and stated specs.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| WEN 429DPC | 9.6 | 28 | 19 | 20 | n/a | 3 |
| Strong Hand PTTD634 | 9.6 | 30 | 21 | 20 | n/a | 0 |
| Elsjoy 2-Pack | 9.6 | 28 | 20 | 21 | n/a | 0 |
| QWORK 2-Pack | 9.6 | 27 | 20 | 21 | n/a | 0 |
| GOSWIFT 9-Inch | 9.4 | 24 | 18 | 19 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.




