Best Beam C Clamp (2026): 5 Picks for Pipe and Cable
Five beam c clamps for hanging pipe and cable from steel beams, compared on load capacity, thread size, jaw opening and the pack size each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallAfcabakila 734911_19.6/10View on Amazon - 2
Best StainlessSaihisday 1″ 25mm9.6/10View on Amazon - 3
Best KitHicarer ZHW-Hicarer-25299.5/10View on Amazon - 4
Best BulkAOKLIT A-1369.5/10View on Amazon
A length of pipe needs to hang from the steel above, and drilling the beam is not an option. The run is already measured, the hangers are on site, and the clamp has to grip the flange and hold the rod without slipping. That is the job a top beam c clamp is built for, and this guide covers the best beam c clamp picks for hanging pipe and cable: five steel clamps from small stainless minis to a top beam clamp built for vertical piping.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Afcabakila 734911_1: 400 lb max load, 3/8-16 UNC thread and 3/4 inch jaw opening in a 10-pack of ductile iron clamps. Check price on Amazon
- Best Stainless Saihisday 1″ 25mm: Stainless steel 1 inch clamps with an M8 screw ring rated to 100 lb of static gravity. Check price on Amazon
- Best Kit Hicarer ZHW-Hicarer-2529: 50 beam clamps with screws plus 50 bridle rings, rated to about 75 lb. Check price on Amazon
- Best Bulk AOKLIT A-136: 100 galvanized steel clamps for 1/2 inch flanges, rated to 75 lb. Check price on Amazon
The machines

Afcabakila 10PCS Top Beam Clamps
A 10-pack of ductile iron top beam clamps with a 3/8-16 UNC thread, 3/4 inch jaw opening and a 400 lb max load capacity.
Pros
- 400 lb max load capacity, the highest here
- 3/8-16 UNC thread fits standard threaded rods
- Ductile iron with galvanization for rust resistance
- Clamps onto steel I-beams without drilling
Cons
- No warranty term stated in the listing
- 3/4 inch jaw opening fits only beams within that opening
- No bridle ring included, so cable rings need a separate purchase
- 10-pack suits one job; a larger job needs more packs

Saihisday 1" 25mm C-Clamps
A 6-pack of stainless steel 1 inch C-clamps with an M8 screw ring, a 0 to 1 inch clamping range and a screw ring rated to 100 lb.
Pros
- M8 stainless steel screw ring rated to 100 lb of static gravity
- Clamping range of 0 to 1 inch fits desks, shelves and steel
- Stainless steel I-beam frame resists rust
- Six clamps in the pack for several mounting points
Cons
- No warranty term stated in the listing
- 1 inch clamping range fits only thin material
- The 100 lb rating covers the screw ring, not the clamp frame
- No cable ring included, so hanging cable needs a separate ring

Hicarer 50 Set 1/4 x 20 Beam Clamp Steel Small C
A 50-set kit of 1/4 x 20 steel beam clamps with screws and 1 1/4 inch bridle rings, rated to about 75 lb, for pipe and cable.
Pros
- 50 clamps and 50 bridle rings cover large installs
- Rated to about 75 lb for pipes, cables and fixtures
- Zinc plated steel resists rust and wear
- Clamps fit beams without drilling, for vertical or horizontal runs
Cons
- Load rating is stated as about 75 lb, not an exact figure
- 1 1/4 inch bridle rings fit only cable that passes the ring
- Fits 1/4-20 threaded rods only; larger rod needs a different clamp
- 50 sets suit large installs; a small job leaves most of the kit unused

AOKLIT 100 Pcs Beam Clamp, 1/4" x 20 Beam Clamps
A 100-pack of galvanized steel 1/4 x 20 beam clamps that fit 1/2 inch flanges and threaded rods or wire rings, rated to 75 lb.
Pros
- 100 clamps in the pack for big installs
- Rated to 75 lb for pipes, cables and heavy equipment
- Fits 1/2 inch flanges with 1/4-20 threaded rods or wire rings
- Galvanized steel resists corrosion in harsh environments
Cons
- No bridle ring or wire ring included
- 75 lb rating is the lowest stated load here
- 1/2 inch flange fit limits the beam size it grips
- 100-pack suits large jobs; a small job leaves most unused

Stainless Steel C Clamps Mini 1 Inch for Mounting
A 6-pack of 1 inch mini stainless steel C clamps with protective pads, two 8 mm screw holes and a 0.2 to 1 inch clamping range.
Pros
- 304 stainless steel resists rust and corrosion
- Protective pads keep the clamped surface from deforming
- Two 8 mm screw holes take hooks or eye bolts
- 1 inch size with 1 inch throat depth for small mounting jobs
Cons
- 1 inch clamping range fits only thin material
- 0.16 inch steel is the thinnest here
- Mini size suits small mounting jobs, not pipe or cable runs
- Six clamps cover a small job; larger installs need more packs
Spec sheet comparison
| Model | Gear Score | Load capacity | Thread / Screw | Pack size | Material | Warranty |
|---|---|---|---|---|---|---|
| Afcabakila 734911_1 | 9.6/10 | 400 lb | 3/8-16 UNC | 10 pcs | Ductile iron, galvanized | None stated |
| Saihisday 1″ 25mm | 9.6/10 | 100 lb screw ring | M8 screw ring | 6 pcs | Stainless steel | None stated |
| Hicarer ZHW-Hicarer-2529 | 9.5/10 | About 75 lb | 1/4-20 | 50 sets | Zinc plated steel | None stated |
| AOKLIT A-136 | 9.5/10 | 75 lb | 1/4-20 | 100 pcs | Galvanized steel | None stated |
| foxwake Mini 1 In | 9.4/10 | Not stated | 8 mm screw holes | 6 pcs | 304 stainless steel | None stated |
All specs here repeat what the maker rates and the listing prints, copied down 22 November 2026.
Buying guide: the best beam c clamp
Match the load rating
Load rating is the first figure to check, and it varies widely here. The Afcabakila clamp is rated to a 400 lb max load, the Saihisday screw ring is rated to 100 lb of static gravity, and the Hicarer and AOKLIT clamps are rated to 75 lb, with the Hicarer figure stated as about 75 lb. The foxwake mini clamp states no load rating, so it suits light mounting rather than hanging pipe. Never exceed the stated load, and never lift over people. Match the rating to the pipe, cable and fittings the clamp will carry, with margin for the hardware itself.
Check the thread and jaw opening
The thread decides what rod or ring the clamp takes. The Afcabakila uses a 3/8-16 UNC thread with a 3/4 inch jaw opening for standard threaded rods. The Saihisday uses an M8 screw ring. The Hicarer and AOKLIT clamps use a 1/4-20 thread, and the AOKLIT fits 1/2 inch flanges. The foxwake mini has two 8 mm screw holes for hooks or eye bolts instead of a rod thread. Check the rod size and the flange thickness on your beam before you order, since a clamp that does not match the thread or the flange cannot be made to fit.
Pick the pack size
Pack size runs from 6 to 100 here, so count the hanging points before you buy. The Afcabakila comes as 10 clamps, the Saihisday and foxwake as 6, the Hicarer as 50 clamps with 50 bridle rings, and the AOKLIT as 100 clamps. A single pipe run needs only a few clamps, while a warehouse sprinkler install needs dozens. The Hicarer kit is the only one here that includes bridle rings, so a cable job needs rings added to any other pick.
Mind the material
Material decides how the clamp holds up in damp or outdoor work. The Afcabakila is ductile iron with a galvanized coating, the AOKLIT is galvanized steel, and the Hicarer is zinc plated steel, all stated to resist rust and corrosion. The Saihisday is stainless steel, and the foxwake is 304 stainless steel, which the maker states is rust-proof and corrosion resistant. Stainless suits damp rooms and outdoor mounts, while galvanized and zinc plated steel suit dry indoor runs. Pick the coating that matches where the clamp will live.
Use as directed. Clamp only onto a beam flange the clamp is sized for, tighten the screw fully, and check the grip before hanging any load. Never exceed the stated load capacity, and never lift or hang loads over people. Keep hands clear while tightening, and inspect the coating and screw before each use. See the OSHA machine guarding page and our Safety Disclaimer.
Before You Strike an Arc
- Measure the flange thickness and check it against the stated jaw opening before ordering.
- Match the thread on the clamp to the rod or ring you already own.
- Check the stated load capacity against the pipe, cable and fittings it will carry.
- Look over the coating and the screw on arrival; a damaged coating rusts first.
- Tighten each clamp fully and tug the rod before hanging the run.
FAQ for welders
How do I use a beam clamp?
Hook the C-shaped clamp over the beam flange, then turn the screw until it grips the flange tight. Hang the threaded rod or ring from the clamp, and check the grip before loading it. No drilling is needed, since the clamp holds by screw pressure on the flange.
How do beam clamps work?
A beam clamp grips a beam flange with a screw that presses the clamp body against the steel. The C shape hooks over the flange, and the screw holds it in place. The rod or ring hangs from the clamp, so the load pulls straight down on the flange.
What load can these beam clamps hold?
The Afcabakila clamp is rated to a 400 lb max load, the Saihisday screw ring to 100 lb of static gravity, and the Hicarer and AOKLIT clamps to 75 lb, with the Hicarer figure stated as about 75 lb. The foxwake mini clamp states no load rating. Never exceed the stated load for the clamp you buy.
Do these beam clamps need drilling?
No. Every clamp here is made to grip a steel beam without drilling: the Afcabakila, Hicarer and AOKLIT clamps all state drill-free mounting, and the Saihisday and foxwake clamps tighten onto the material with a screw. Drilling is not needed to install any pick in this guide.
What thread sizes do these beam clamps use?
The Afcabakila uses a 3/8-16 UNC thread, the Saihisday uses an M8 screw ring, and the Hicarer and AOKLIT clamps use a 1/4-20 thread. The foxwake mini has two 8 mm screw holes for hooks or eye bolts. Match the thread to the rod or ring you plan to hang.
Related: lifting and pressing hub, best lifting trolley, best steel plate clamp, best lifting beam, best lifting eye bolt, come along vs lever hoist, and best lifting bridle.
Scoring, line by line
Each clamp is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No clamp here states a safety certification, so every clamp here scores zero on that criterion; the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Afcabakila 734911_1 | 9.6 | 30 | 21 | 21 | n/a | 0 |
| Saihisday 1″ 25mm | 9.6 | 28 | 20 | 20 | n/a | 0 |
| Hicarer ZHW-Hicarer-2529 | 9.5 | 27 | 20 | 20 | n/a | 0 |
| AOKLIT A-136 | 9.5 | 26 | 19 | 20 | n/a | 0 |
| foxwake Mini 1 In | 9.4 | 23 | 19 | 19 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.




