Best 4 in 1 Welder Under 125 (2026): 5 Picks Scored
Five 4 in 1 welders under 125, compared on output, input voltage, weight, thickness, what ships in the box and the warranty in writing.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallDURATECH DT1050739.6/10View on Amazon - 2
Lightest PickFutelo MIG-1609.5/10View on Amazon - 3
Highest OutputHGNVGZ MIG 200XP9.5/10View on Amazon - 4
Best Stick ControlsAZZUNO MIG-145L-29.5/10View on Amazon - 5
Simplest 110V PickFEMEROL MIG1359.4/10View on Amazon
A fence hinge torn off its post, a mower deck cracked along a seam, a trailer fender that needs a bead laid down before the next haul. That is the work waiting on the bench, and it calls for one machine that can switch between gas MIG, gasless flux core, stick and lift TIG without a second machine taking up floor space. This guide covers the best 4 in 1 welder under 125: five multi-process machines scored on output, input voltage, weight, thickness and the warranty in writing.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall DURATECH DT105073: CSA certified, 140A on 120V, welds 3/16 inch low carbon steel, takes 5 kg spools. Check price on Amazon
- Lightest Pick Futelo MIG-160: 160A dual voltage at 7.7 lb, with synergic control and a large LED display. Check price on Amazon
- Highest Output HGNVGZ MIG 200XP: 200A for mild steel up to 1/4 inch, plus a spool gun connector for aluminum. Check price on Amazon
- Best Stick Controls AZZUNO MIG-145L-2: 145A dual voltage with VRD, Arc Force, Hot Start and 2T, 4T and SPOT modes. Check price on Amazon
- Simplest 110V Pick FEMEROL MIG135: 135A on 110V with synergic control and an 8.2 ft torch, at 11.7 lb. Check price on Amazon
The machines

DURATECH 140Amp MIG Welder
A 140A 120V multi-process welder with a stated CSA certification, IP21S protection rating and support for 5 kg wire spools.
Pros
- CSA certified and fully complies with U.S. standards
- Welds up to 3/16 inch of low carbon steel plate
- Compatible with 5 kg wire spools and 2 lb and 11 lb rolls of wire
- IP21S protection rating with over-current, overload, over-voltage and overheat protection
Cons
- 120V only, with no 220V input stated
- Lift TIG needs an additional torch, bought separately
- No warranty term is stated in the listing
- No duty cycle rating is stated in the listing

Futelo 160A MIG Welder, 4 in 1 Gas/Gasless MIG
A 160A dual voltage 4 in 1 welder at 7.7 lb, with synergic control, a large LED display and a full ready-to-weld kit.
Pros
- 160A output on 110V/220V dual voltage with synergic control
- Lightest pick here at 7.7 lb
- Large LED display shows real-time amperage
- Full kit in the box, including torch, goggles, gloves, rods, wire and gas hose
Cons
- Lift TIG needs a torch bought separately
- No warranty term is stated; only a 30-day money-back guarantee
- No thickness rating is stated in the listing

HGNVGZ MIG 200XP 4-in-1 Welder 110V/220V Dual
A 200A dual voltage 4 in 1 welder at 8.8 lb, with a spool gun connector for aluminum and a 1/4 inch mild steel rating.
Pros
- Highest output here at 200A, rated for mild steel up to 1/4 inch thick
- Spool gun connector for aluminum, the only pick here that states one
- Light at 8.8 lb with a built-in carrying handle
- Kit includes a welding helmet, gloves, chipping hammer and brush
Cons
- Gas regulator, hose and auto-darkening helmet are not included
- No warranty term is stated in the listing
- No wire sizes are stated in the listing
- No duty cycle rating is stated in the listing

AZZUNO 4 in 1 MIG Welder
A 145A dual voltage 4 in 1 welder with 2T, 4T and SPOT functions and adjustable VRD, Arc Force and Hot Start in stick mode.
Pros
- 145A on 110V/220V dual voltage with synergic control
- Stick mode has adjustable VRD, Arc Force and Hot Start
- 2T, 4T and SPOT functions with a manual wire feed button
- Takes .030, .035 and .040 inch flux-cored wire, .030 inch solid wire and E6013 electrodes
Cons
- No warranty term is stated in the listing
- No thickness rating is stated in the listing
- No duty cycle rating is stated in the listing

FEMEROL MIG Welder 110V 4 in 1 Multiprocess
A 135A 110V 4 in 1 welder at 11.7 lb, with synergic control, fine adjustment of ±3V and an 8.2 ft MIG torch.
Pros
- Synergic control with fine adjustment of ±3V
- 8.2 ft MIG torch in the box
- Light at 11.7 lb for outdoor use and easy transport
- Over-current, over-voltage and over-heating protection
Cons
- 110V only, with no 220V input stated
- Lowest output here at 135A
- No duty cycle rating is stated in the listing
- No thickness rating is stated in the listing
Other welders and gear to compare
MIG Welder 160ACheck price on Amazon
ARCCAPTAIN Flux Core Welding Wire .030“ & .035" E71T-GS MigCheck price on Amazon
WORKPRO 3-Piece Locking Pliers SetCheck price on Amazon
YixangDD 2 Pack 030 Flux Core Welding WireCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Output | Input voltage | Weight | Thickness | Warranty |
|---|---|---|---|---|---|---|
| DURATECH DT105073 | 9.6/10 | 140A | 120V | 15 lb | 3/16 in low carbon steel | Not stated |
| Futelo MIG-160 | 9.5/10 | 160A | 110V/220V | 7.7 lb | Not stated | 30-day money-back |
| HGNVGZ MIG 200XP | 9.5/10 | 200A | 110V/220V | 8.8 lb | 1/4 in mild steel | Not stated |
| AZZUNO MIG-145L-2 | 9.5/10 | 145A | 110V/220V | 13 lb | Not stated | Not stated |
| FEMEROL MIG135 | 9.4/10 | 135A | 110V | 11.7 lb | Not stated | Two-year guarantee |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 30 October 2026. Where a listing states a figure two ways, the table shows both.
How the picks were scored
Each welder is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| DURATECH DT105073 | 9.6 | 28 | 21 | 20 | 8 | 0 |
| Futelo MIG-160 | 9.5 | 32 | 21 | 21 | 0 | 0 |
| HGNVGZ MIG 200XP | 9.5 | 30 | 20 | 22 | 0 | 0 |
| AZZUNO MIG-145L-2 | 9.5 | 29 | 21 | 21 | 0 | 0 |
| FEMEROL MIG135 | 9.4 | 27 | 20 | 20 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.
How to pick the best 4 in 1 welder under 125
Output and input voltage
Output among these picks runs from 135A to 200A. Three of the five list 110V and 220V input, while the DURATECH lists 120V only and the FEMEROL lists 110V only. The Futelo includes a 220V to 110V power plug in the box, and the DURATECH includes a 15-20A adapter plug. Check the input voltage the listing states against the circuit in the shop before ordering.
Weight and portability
Weights run from 7.7 lb for the Futelo to 15 lb for the DURATECH, with the HGNVGZ at 8.8 lb, the FEMEROL at 11.7 lb and the AZZUNO at 13 lb in its bullets. The Futelo listing states it is 40% lighter than typical 12 to 15 lb welding machines and can be lifted with one hand. Two listings disagree with themselves on weight: the Futelo spec table states 7.47 pounds against 7.7 lb in the bullets, and the AZZUNO spec table states 12.0 pounds against 13 lb in the bullets. Plan on the bullet figures.
Thickness and wire
Only two listings state a thickness rating. The DURATECH welds thicknesses up to 3/16 inch of low carbon steel plate, and the HGNVGZ handles mild steel up to 1/4 inch thick. The other three state no thickness figure. Wire sizes run from 0.025 inch to 0.035 inch on the DURATECH, 0.030 inch and 0.035 inch on the FEMEROL, and .030, .035 and .040 inch flux-cored wire plus .030 inch solid wire and E6013 electrodes on the AZZUNO. The DURATECH takes 5 kg spools and 2 lb and 11 lb rolls of wire.
What ships in the box
Every pick here ships ready to weld in some form, but the contents differ. The Futelo box is the fullest, with a MIG torch, goggles, gloves, rods, wire, a gas hose, an earth clamp and an electrode holder. The HGNVGZ kit adds a welding helmet, gloves, a chipping hammer and a brush, but the listing states the gas regulator, hose and auto-darkening helmet are not included. The FEMEROL box includes a 2 meter gas hose and 0.030 inch flux cored wire, and the AZZUNO box includes both flux-cored and solid wire. Lift TIG needs a torch bought separately on the Futelo and DURATECH listings.
Warranty and safety listings
Only one pick here states an electrical safety certification: the DURATECH is CSA certified and fully complies with U.S. standards, with an IP21S protection rating and over-current, overload, over-voltage and overheat protection. The FEMEROL states over-current, over-voltage and over-heating protection, and the HGNVGZ states over-current, over-load and over-heating protection. On warranty, the Futelo states a 30-day money-back guarantee with 24-hour customer support, and the FEMEROL states a two-year guarantee. The other listings state no warranty term.
Before You Strike an Arc
- Check the input plug and voltage the listing states, 110V, 120V or 220V, against the circuit in the shop before plugging in.
- Fit the wire the listing states for the process: flux-cored or solid wire in the sizes the machine takes, and E6013 electrodes for stick on the AZZUNO.
- Lift TIG needs a torch bought separately on the Futelo and DURATECH listings, and the HGNVGZ listing states the gas regulator and hose are not included.
- Check the box against the listing on arrival: torch, earth clamp, electrode holder, gloves, rods and wire.
- Wear a helmet and gloves, keep the work area clear of anything that can burn, and work with ventilation.
FAQ for welders
Can a 4 in 1 welder run on a standard household circuit?
Four of the five picks list 110V input, and the DURATECH lists 120V input, so each one plugs into household power on its stated voltage. The Futelo includes a 220V to 110V power plug, and the DURATECH includes a 15-20A adapter plug. Running on the higher 220V input needs a 220V circuit, so check the listing and the shop circuit before ordering.
What thickness can these welders handle?
Two listings state a thickness rating. The DURATECH welds thicknesses up to 3/16 inch of low carbon steel plate, and the HGNVGZ handles mild steel up to 1/4 inch thick. The Futelo, FEMEROL and AZZUNO listings state no thickness figure, so their thickness limits are not published.
Do I need a gas bottle to weld with these machines?
Not for flux core work: every pick here runs gasless flux core, and gas MIG needs a bottle and regulator. Lift TIG needs a torch bought separately on the Futelo and DURATECH listings. The HGNVGZ listing states the gas regulator and hose are not included, so plan on buying those separately when setting up gas MIG.
What wire sizes do these welders take?
The DURATECH takes wire from 0.025 inch to 0.035 inch and fits 5 kg spools and 2 lb and 11 lb rolls. The FEMEROL takes 0.030 inch and 0.035 inch wire. The AZZUNO takes .030, .035 and .040 inch flux-cored wire, .030 inch solid wire and E6013 electrodes. The Futelo and HGNVGZ listings state no wire sizes.
Which of these welders is the lightest?
The Futelo is the lightest at 7.7 lb, followed by the HGNVGZ at 8.8 lb. The FEMEROL weighs 11.7 lb, the AZZUNO lists 13 lb in its bullets, and the DURATECH weighs 15 lb. The Futelo listing states it is 40% lighter than typical 12 to 15 lb welding machines.
Related: best 4 in 1 welder for multi-process picks without a price ceiling, best multi-process welder, and the best welding cart under 200. Also see the best extension cord for mig welder, flux core vs mig for outdoor use.




