Argon vs Helium for Mig Welding: Which One Should You Buy?
Argon is the stocked cylinder gas in these listings, while helium uses the same regulator inlet and hose family, so the choice comes down to the cylinder you can source.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SPARC Argon Regulator & Flow Meter9.8/10View on Amazon - 2
SPARC Premium Dual Argon Regulator for TIG/MIG Welding9.8/10View on Amazon - 3
ARCCAPTAIN Argon/CO2/Helium Regulator9.7/10View on Amazon - 4
YESWELDER Welding Gas FlowmeterView on Amazon - 5
40 cu/ft 75% Argon 25% CO2 Welding Gas Cylinder Tank CGA 580View on Amazon - 6
Argon Co2 Professional Gas Flow Meter Tester FlowmeterView on Amazon - 7
YESWELDER Dual Output Argon Regulator Flow Meter Two OutletsView on Amazon - 8
20 cu ft Steel Argon CylinderView on Amazon - 9
Flame Tech Argon RegulatorView on Amazon
For MIG welding, the listings here stock argon as the cylinder gas: an 80 cu ft 100% argon cylinder on a CGA 580 connection. Helium has no cylinder in these listings, but the gear treats both gases the same way: the YESWELDER regulator connects to argon, helium and argon/CO2 tanks through one CGA-580 inlet, and the OYHBO hose lists argon, argon/CO2 mixture and helium compatibility. So argon vs helium for mig welding, as these listings describe it, is mostly a sourcing question: argon is the stocked cylinder, and helium needs the same fittings and regulator family.
Other welders and gear to compare
YESWELDER Welding Gas FlowmeterCheck price on Amazon
40 cu/ft 75% Argon 25% CO2 Welding Gas Cylinder Tank CGA 580Check price on Amazon
Argon Co2 Professional Gas Flow Meter Tester FlowmeterCheck price on Amazon
YESWELDER Dual Output Argon Regulator Flow Meter Two OutletsCheck price on Amazon
20 cu ft Steel Argon CylinderCheck price on Amazon
Flame Tech Argon RegulatorCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Argon vs helium for mig welding side by side
| Argon | Helium | What the gear says | |
|---|---|---|---|
| Cylinder stocked here | 80 cu ft 100% argon cylinder, CGA 580 | No helium cylinder in these listings | Cylinder-only listing, no regulator stated |
| Regulator connection | CGA-580 inlet | Same CGA-580 inlet | YESWELDER: connects to argon, helium, argon/CO2 |
| Flow readout | 0 to 60 CFH tube | Same tube, gas-agnostic | 1.5 in gauge, 0 to 4000 PSI |
| Hose compatibility | Listed | Listed | OYHBO: argon, argon/CO2, helium; 300 PSI working |
| Flow at the torch | Peashooter reads 0 to 25 L/min | Stated for all gases | Reads at the nozzle, 1 L graduations |
Flow numbers are stated ranges, not settings: the YESWELDER tube reads 0 to 60 CFH and the peashooter reads 0 to 25 litres per minute. What flow you actually run comes from your machine manual, not the gear listing.
What argon gets you in these listings
The COLIBROX listing is an 80 cu ft 100% argon cylinder on a CGA 580 connection, full, at 50 pounds. The maker states a 10 year inspection date stamped on the tank, with every cylinder within 2 years of its stamped date, meeting DOT and ISO regulations. Shipping is stated for the continental US only. No regulator is stated in the package: that is a separate buy, and the YESWELDER package covers the regulator side with a hose clamp and a mounting nut.
What helium gets you in these listings
Less, honestly. No helium cylinder is listed, so the listings do not give a helium cylinder size, weight or price. What they do say: the YESWELDER regulator connects to helium tanks with no additional adapters needed, and the OYHBO hose is compatible with helium as well as argon and argon/CO2 mixture. If you source a helium cylinder, the regulator and hose family in these listings already fits it.
The gear that goes with shielding gas
YESWELDER flowmeter regulator. Brass body with a CGA-580 inlet nut, a flow tube reading 0 to 60 CFH with a floating ball, and a 1.5 inch pressure gauge reading 0 to 4000 PSI. Fits female 9/16 x 18 nuts and male 5/8 x 18 fittings, with a 1/4 inch barbed fitting for common welding hoses. The package states 1 argon regulator, 1 hose clamp and 1 mounting nut, at 1.5 pounds.
COLIBROX 80 cu ft argon cylinder. 100% argon, CGA 580, full, 50 pounds, with a 10 year inspection date stamped and DOT and ISO regulations met. A cylinder-only listing: pair it with a regulator and hose.
OYHBO inert gas hose. 6.56 feet of rubber hose with 5/8 inch UNF-18RH fittings on each end, listed for argon, argon/CO2 mixture, helium and other welding gases. Stated 300 PSI working pressure and 900 PSI burst pressure, hard to harden in cold weather per the maker.
Sxstar peashooter flow meter. A peashooter-style meter scaled 0 to 25 litres per minute in one litre graduations, placed over the MIG or TIG nozzle to read gas flow from the top of the ball. Stated for all gases, at 0.352 ounces.
Compressed gas is heavy and pressurized. Secure cylinders upright with a chain, keep them away from arc and sparks, and move them with a cart, not by the valve. See the OSHA welding overview and our Safety Disclaimer.
Shielding gas buying advice
Start with the cylinder, because everything else hangs off it. The COLIBROX listing is an 80 cu/ft 100% argon cylinder on a CGA 580 connection, shipped full at 50 pounds, with a 10 year inspection date stamped and DOT and ISO regulations met. Shipping is stated for the continental US only, so plan for freight-size delivery. A full cylinder is the convenience buy; empty cylinders from a local supplier are the usual long-term route. Either way, the CGA 580 valve is the standard thread that the YESWELDER flowmeter screws straight into, with no additional adapters needed per its listing.
Then match the regulator and hose to the cylinder. The YESWELDER flowmeter has a brass body with a CGA-580 inlet nut, a flow tube reading 0 to 60 CFH with a floating ball, and a 1.5 inch pressure gauge reading 0 to 4000 PSI. It fits female 9/16 x 18 nuts and male 5/8 x 18 fittings, with a 1/4 inch barbed fitting for common welding hoses, and the package states 1 argon regulator, 1 hose clamp and 1 mounting nut at 1.5 pounds. The OYHBO hose is 6.56 feet of rubber with 5/8 inch UNF-18RH fittings on each end, stated for argon, argon/CO2 mixture, helium and other welding gases, with 300 PSI working pressure and 900 PSI burst pressure. The maker states it is hard to harden in cold weather, which matters for an unheated garage in winter.
Finally, verify flow at the torch. The Sxstar peashooter is scaled 0 to 25 litres per minute in one litre graduations and stated for all gases at 0.352 ounces: place it over the MIG or TIG nozzle and read from the top of the ball. The listings give ranges, not settings, so take the actual flow number from your machine manual. For helium, note that no helium cylinder is listed here; the regulator and hose family already fits helium tanks, so the cylinder is the only missing piece to source.
FAQ for welders
Can one regulator handle both argon and helium?
Per the YESWELDER listing, yes. It connects to argon, helium and argon/CO2 tanks through the CGA-580 inlet nut, and the maker says no additional adapters are needed. The flow tube reads 0 to 60 CFH for any of them.
What flow rate should I set for MIG?
The listings do not state a setting, only ranges. The YESWELDER tube reads 0 to 60 CFH, and the peashooter reads 0 to 25 litres per minute at the nozzle. Take the setting from your machine manual or door chart.
Does the argon cylinder come with a regulator?
No regulator is stated in the COLIBROX listing: it is a cylinder-only listing. The YESWELDER package states 1 argon regulator, 1 hose clamp and 1 mounting nut, so the regulator is the separate buy.
How long will an 80 cu ft cylinder last?
Not from these listings alone. The cylinder states 80 cu ft, and runtime depends on the flow you set, which the listings do not prescribe. Check your machine manual for the flow it calls for.
Do I need a different hose for helium?
Not per the OYHBO listing. It lists compatibility with argon, argon/CO2 mixture, helium and other welding gases, with 5/8 inch UNF-18RH fittings, a stated 300 PSI working pressure and 900 PSI burst pressure.
How do I check flow at the torch?
The Sxstar peashooter is scaled 0 to 25 litres per minute in one litre graduations. Place it over the MIG or TIG nozzle and read the flow from the top of the ball. The listing states it for all gases.
Related: rent vs buy a welding gas cylinder, best gas regulator for MIG welding, what size gas bottle for home welding, and the welding consumables hub.




