Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Angle Grinder Cutting Guide for Clean Cuts

An angle grinder cutting guide that shows how to pick the right wheel for the metal and cut cleanly, with a diamond wheel, a thin bonded wheel and a deep pack scored for the shop.

Angle Grinder Cutting Guide for Clean Cuts
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1FOXBC 4-1/2 Inch Diamond Cutting Wheel Metal CutFOXBC 4-1/2 Inch Diamond Cutting Wheel Metal Cut9.7/10View on Amazon
  2. 2VOISEN 4 1/2 Cut Off Wheel,70 PCS Angle GrinderVOISEN 4 1/2 Cut Off Wheel,70 PCS Angle Grinder9.6/10View on Amazon
  3. 3SALI 5 Pack Cut Off Wheel 4 1/2 Inch CuttingSALI 5 Pack Cut Off Wheel 4 1/2 Inch Cutting9.5/10View on Amazon

A length of angle iron waits on the bench, a steel plate needs trimming to fit, and a piece of rebar has to come down to size. An angle grinder cutting guide answers the question before any sparks fly: which wheel cuts the metal cleanly, and how do you run it so the cut stays straight and the wheel stays in one piece. Pick the wheel for the metal, set the guard and the work, and let the wheel do the cutting.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

FOXBC 4-1/2 Inch Diamond Cutting Wheel Metal Cut

FOXBC 4-1/2 Inch Diamond Cutting Wheel Metal Cut

FOXBC9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A diamond rimmed wheel rated for 5000+ cuts on rebar, with a solid steel body and a 3 pack for the shop.

Pros

  • Diamond rimmed edge rated for 5000+ cuts on rebar
  • Maker claims 100X longer cutting life than one standard bonded cut-off disc
  • Solid steel wheel body that does not shatter or break when dropped
  • More control with less sparks and less dust than bonded discs

Cons

  • 3 pack gives fewer wheels than the 70 pack here
  • 0.1 in wheel cuts a wider kerf than the thin bonded wheels here
  • Maker describes it for dry cutting, with no wet cutting use stated
  • No warranty term is stated
VOISEN 4 1/2 Cut Off Wheel,70 PCS Angle Grinder

VOISEN 4 1/2 Cut Off Wheel,70 PCS Angle Grinder

VOISEN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 70 pack of ultra thin aluminum oxide wheels rated to 13,300 rpm for fast, burr free cutting.

Pros

  • 70 pack covers a long run of cuts without reordering
  • Maker claims 2 times the cutting life of a normal cutting wheel
  • Rated to 13,300 rpm
  • Double fiberglass mesh reinforced for safety and durability

Cons

  • No warranty term is stated
  • 70 pack suits a busy shop better than a reader who cuts rarely
  • Only one wheel size in the pack, so it fits 4.5 inch grinders only
  • Aluminum oxide grain, with no diamond edge in this pack
SALI 5 Pack Cut Off Wheel 4 1/2 Inch Cutting

SALI 5 Pack Cut Off Wheel 4 1/2 Inch Cutting

SALI9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5 pack of thin 0.045 inch aluminum oxide wheels rated to 13,300 rpm for fast, burr free cutting.

Pros

  • Thin 0.045 inch wheel for fast, burr free cutting
  • Rated to 13,300 rpm
  • Double fiberglass mesh reinforced for safety and durability
  • Aluminum oxide grain for aggressive cutting and long life

Cons

  • 5 pack runs out fast on a big cutting job
  • Thin 0.045 inch wheel is made for cutting, not grinding
  • Fits 4.5 inch grinders only
  • Aluminum oxide grain wears faster than the diamond edge here

Angle grinder cutting guide: the short version

Match the wheel to the metal and to the grinder, clamp the work so it cannot move, and cut with steady pressure while the guard stays in place. A thin bonded wheel suits clean cuts in light stock, a diamond rimmed wheel suits rebar, angle iron and pipe that wears bonded wheels down fast, and a deep pack suits a shop that cuts often.

Pick the wheel for the metal

Start with what the wheel is made to cut. The wheels here cover carbon steel, stainless steel, pipe, iron, copper and other ferrous metals, and the diamond wheel also names rebar, angle iron, cast iron, alloy steel and aluminum. Match the wheel to the metal on the bench, and the cut stays cleaner than forcing a wheel through metal it was never made for.

Thin wheels cut fast with little burr, and the thin wheels here use aluminum oxide grain for aggressive cutting. The diamond wheel trades a thin kerf for a solid steel body and a diamond edge that holds up on rebar and angle iron. Pack size matters too: a small pack suits a short job, and a deep pack suits a shop that cuts often.

Cutting wheels for this guide

The wheels below cover the cuts this guide walks through: a thin bonded wheel for clean cuts in metal and stainless steel, a diamond wheel for rebar and angle iron, and a deep pack for a shop that cuts often.

Side by side

Wheel Pack size Wheel size Max speed Abrasive Reinforcement
FOXBC Diamond Cutting Wheel 3 Pack 3 4.5 in Not stated Diamond Solid steel body
VOISEN 70 Pack Cut Off Wheel 70 4.5 in 13,300 rpm Aluminum oxide Double fiberglass mesh
SALI 5 Pack Cut Off Wheel 5 4.5 in 13,300 rpm Aluminum oxide Double fiberglass mesh

The diamond wheel is the long life pick, the deep pack is the volume pick, and the thin 5 pack is the light stock pick. Each wheel here is a 4.5 inch wheel for a 4.5 inch grinder, so the choice comes down to the metal, the job size, and how many wheels the shop wants on hand.

Set the grinder up before the cut

Clamp the work so it cannot move, and keep the guard in place with eye and face protection on. No gloves near rotating parts, and clear the bench of anything flammable before the wheel spins. Check the wheel for cracks or chips before mounting it, and match the wheel to the grinder it fits. OSHA machine guarding rules cover guards and safe grinder setup, and the grinder manual states the wheel sizes the machine takes.

Make the cut

Mark the line, start the wheel away from the metal, and let it reach full speed before it touches the work. Feed the wheel into the cut with steady pressure and let the wheel do the work, without leaning on it or twisting it sideways. A cutting wheel cuts in a straight line, and side pressure bends a thin wheel and can break it. Let the wheel stop on its own before setting the grinder down.

For more options, see our metal fab tools guides.

FAQ for welders

Can a cutting wheel cut stainless steel?

Yes. The thin wheels here name stainless steel, and the diamond wheel names it too. Use a wheel that names stainless steel, keep the cut steady, and let the wheel do the work so the edge stays clean.

How long does a diamond cutting wheel last?

The maker of the diamond wheel here rates it for 5000+ cuts on rebar and claims 100X longer cutting life than one standard bonded cut-off disc. How long a wheel lasts in the shop depends on the metal, the pressure on the wheel, and how the wheel is stored, so treat the rating as the maker claim and keep a spare wheel on hand.

What size wheel fits a 4.5 inch grinder?

A 4.5 inch wheel made for a 4.5 inch grinder. Each wheel here is a 4.5 inch wheel, and the listings name 4.5 inch angle grinders as the fit. Check the grinder manual for the wheel size it takes before ordering.

Do these wheels cut rebar and angle iron?

The diamond wheel names rebar, angle iron, cast iron, stainless steel, alloy steel, aluminum, pipes and sheet metal for dry cutting. The thin bonded wheels name metal and stainless steel, pipe, iron, copper and ferrous metals. Pick the wheel that names the metal on the bench.

Why pick a thin wheel?

A thin wheel cuts fast with little burr and little material loss, which suits clean cuts in light stock. The thin wheels here are 0.045 inch and ultra thin, and both use aluminum oxide grain with a double fiberglass mesh reinforcement.

Related: best angle grinder for cutting metal, best angle grinder, hacksaw vs angle grinder for metal, and best chop saw for metal cutting.

More buying guides