Hacksaw vs Angle Grinder for Metal: Which One Should You Buy?
Two hacksaws and one 4.5 inch angle grinder compared on power, blades, weight and warranty: hand tools against 11 amps and 11,000 rpm.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
DEWALT Angle Grinder, 4.5 Inch, 11 Amp9.5/10View on Amazon - 2
DOWELL Hacksaw Set, 3 Pcs Hack Saws for Metal9.5/10View on Amazon - 3
Pasco 4290 Tiny Tim Hacksaw9.3/10View on Amazon
Verdict. Pick the DEWALT angle grinder when the job is cutting a lot of metal fast: 11 amps and 11,000 rpm against hand power. Pick a hacksaw when the cut is small, the work is far from an outlet, or sparks and noise are a problem. The DOWELL set covers full-size cuts with three frames and spare blades; the Pasco Tiny Tim fits where nothing else reaches.
A piece of angle iron needs trimming and the nearest outlet is across the yard. The hacksaw vs angle grinder for metal question is really about the job: how much metal, how fast, and where. This comparison puts two hacksaws against one 4.5 inch angle grinder on what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Hacksaw vs angle grinder for metal: the three tools compared
| # | Product | Gear Score | Buy |
|---|---|---|---|
| 1 | DEWALT Angle Grinder, 4.5 Inch, 11 Amp | 9.5/10 | Buy on Amazon |
| 2 | DOWELL Hacksaw Set, 3 Pcs Hack Saws for Metal | 9.5/10 | Buy on Amazon |
| 3 | Pasco 4290 Tiny Tim Hacksaw | 9.3/10 | Buy on Amazon |

DEWALT Angle Grinder, 4.5 Inch, 11 Amp
A 4.5 inch, 11 amp corded angle grinder at 11,000 rpm with a paddle switch and a 3 year limited warranty.
Pros
- 11 amp AC/DC motor at 11,000 rpm, 1.8 HP
- Paddle switch with safety lock-off against accidental starts
- One-touch guard rotates 360 degrees with a single action
- 3 year limited warranty
Cons
- 6.2 pounds, the heaviest here
- Corded electric, so the work stays near an outlet
- No disc stated in the included components
- Auto-off brushes stop the tool when the brushes wear out

DOWELL Hacksaw Set, 3 Pcs Hack Saws for Metal
A 3-piece hacksaw set with 12, 10 and 6 inch frames plus 8 extra blades, carbon steel blades and aluminum alloy frames.
Pros
- Three frames, 12, 10 and 6 inch, plus 8 extra blades
- 24TPI carbon steel blades for metal, 8TPI for wood
- 90 and 45 degree blade mounting on the 12 inch frame
- Aluminum alloy frames with ergonomic non-slip grips
Cons
- No warranty term is stated
- Blades are consumables; the listing says to replace them when teeth wear
- Manual cutting is slow next to a powered grinder

Pasco 4290 Tiny Tim Hacksaw
A compact 6 inch mini hacksaw with a 32-tooth alloy steel blade and vinyl grip handle for tight areas.
Pros
- Compact 6 inch frame for tight areas
- 32-tooth alloy steel blade cuts steel and brass
- Vinyl grip handle
- 3.84 ounces, the lightest here
Cons
- 6 inch blade only; short strokes on long cuts
- No spare blades included
- Warranty type stated with no term or length
- Plastic handle
Other welders and gear to compare
EXKRAEFT Flap Discs 4 1/2 for Angle GrinderCheck price on Amazon
3 x 3/8'' Flap Discs for Angle GrinderCheck price on Amazon
Flap Discs 5" for Angle Grinder Self-Sharpening PurpleCheck price on Amazon
20 PCS Flap Discs 4.5" for Angle Grinder Type 29Check price on Amazon
10 Pack Flap Discs 4-1/2" for Angle Grinder 40 Grit T29Check price on Amazon
397661-01 Grinder Guard 4-1/2" 4.5inch Replace for AngleCheck price on Amazon
Side by side
| DEWALT DWE402 Grinder | DOWELL 3-Pc Hacksaw Set | Pasco Tiny Tim Hacksaw | |
|---|---|---|---|
| Power | 11 amp corded electric | Manual | Manual |
| Speed | 11,000 rpm | Not stated | Not stated |
| Blade / disc | 4.5 inch | 12, 10 and 6 inch | 6 inch |
| Weight | 6.2 lb | 0.94 kg | 3.84 oz |
| Warranty | 3 year limited | Not stated | Limited, no term stated |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 22 October 2026. No listing here states a CSA, UL or ETL listing.
Power: hand vs corded
The DEWALT is the only powered tool here: an 11 amp, 120V corded motor rated at 11,000 rpm and 1.8 HP. The DOWELL and Pasco hacksaws are manual, so their cutting speed is whatever your arm gives them. If the work is far from an outlet, the corded grinder stays home; the hacksaws go anywhere.
Cutting speed
Only the DEWALT states a speed figure, 11,000 rpm, so there is no listing-to-listing speed comparison to make. In practice a grinder removes metal far faster than a hand saw, but the listings do not give a cut rate, so treat speed as a power-source difference, not a measured one. For a few cuts in thin stock, the setup time of the grinder can eat the advantage.
Blades and discs
The DOWELL set ships three frames, 12, 10 and 6 inch, plus 8 extra blades: 24TPI carbon steel blades for metal and 8TPI blades for wood on the 12 inch frame. The Pasco carries one 6 inch, 32-tooth alloy steel blade and no spares. The DEWALT box lists a guard, a side handle and a wrench, with no disc stated, so budget for cutting discs separately.
Weight and handling
The DEWALT weighs 6.2 pounds, the DOWELL set 0.94 kg for all three saws, and the Pasco 3.84 ounces. The grinder adds a paddle switch with a safety lock-off, a one-touch guard that rotates 360 degrees, and a side handle. The hacksaws add nothing powered: the DOWELL offers 90 and 45 degree blade mounting on the 12 inch frame, and the Pasco offers a compact frame for tight areas.
Warranty
The DEWALT states a 3 year limited warranty. The Pasco spec table names a limited warranty type with no term or length, so it earns no warranty points. The DOWELL listing states no warranty at all.
Choose the DEWALT DWE402 grinder if
- You cut metal often and want the job done fast.
- You have a 120V outlet or generator at the work site.
- You want a stated 3 year limited warranty.
- Sparks, noise and dust are acceptable where you work.
Choose a hacksaw if
- The work is far from power, or the cut list is short.
- You want quiet, spark-free cutting, indoors or out.
- You want spare blades in the box, as the DOWELL set provides.
- The cut is in a tight spot, where the Pasco Tiny Tim fits.
FAQ for welders
Is a hacksaw or an angle grinder better for cutting metal?
It depends on the job. The DEWALT grinder cuts far faster with 11 amps and 11,000 rpm, but it needs a 120V outlet and throws sparks. A hacksaw is slower, quiet and spark-free, and it works anywhere. For a few small cuts, the hacksaw often wins on simplicity.
Can the DEWALT DWE402 cut metal?
Yes, it is a 4.5 inch metal cutting grinder: 11 amp, 11,000 rpm, with a paddle switch and guard. The box lists the guard, side handle and wrench, but no disc, so buy metal cutting discs rated at or above 11,000 rpm separately.
What blades come with the DOWELL hacksaw set?
Three frames in 12, 10 and 6 inch plus 8 extra blades: 24TPI carbon steel blades for metal and 8TPI blades for wood on the 12 inch frame. The listing calls blades consumables and says to replace them when the teeth wear. The spec table total of 288 teeth covers the whole set, not one blade.
Will the Pasco Tiny Tim cut steel?
The bullets say it cuts steel and brass, with a 6 inch, 32-tooth alloy steel blade. It is made for tight areas, not long cuts: the short frame means short strokes. No spare blades are included.
Do any of these need an outlet?
Only the DEWALT: it is corded electric at 120V and 11 amps. The DOWELL and Pasco hacksaws are fully manual and need no power at all.
Related: best angle grinder, best angle grinder for cutting metal, best angle grinder for welding prep.
Scoring, line by line
All three tools are scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| DEWALT DWE402 Grinder | 9.5 | 30 | 21 | 20 | 0 | 3 |
| DOWELL 3-Pc Hacksaw Set | 9.5 | 28 | 20 | 22 | 0 | 0 |
| Pasco Tiny Tim Hacksaw | 9.3 | 23 | 19 | 19 | 0 | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.
Before you strike an arc. An angle grinder throws sparks and debris: wear a face shield over safety glasses, gloves and flame resistant clothing, and keep the guard on the tool. Clamp the work before cutting, keep the disc rated at or above the grinder’s 11,000 rpm, and clear anything flammable from the area.




