Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Tig Welding Gas Types: Argon, Helium and CO2 Explained

Tig welding gas types come down to argon first, helium for extra heat, and CO2 for MIG only, with CGA-580 regulators metering the gases to the torch.

Tig Welding Gas Types: Argon, Helium and CO2 Explained
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1BETOOLL Dual Output Argon RegulatorBETOOLL Dual Output Argon Regulator9.6/10View on Amazon
  2. 2Muphop Argon Regulator Flow Meter GaugeMuphop Argon Regulator Flow Meter Gauge9.6/10View on Amazon
  3. 3YESWELDER Argon CO2 Regulator with 8.2 ft HoseYESWELDER Argon CO2 Regulator with 8.2 ft Hose9.6/10View on Amazon
  4. 4BOWELD Argon/CO2 Mig Tig Flow Meter Gas RegulatorBOWELD Argon/CO2 Mig Tig Flow Meter Gas Regulator9.5/10View on Amazon

A TIG weld lives or dies on its shielding gas, and the gas choice starts before the arc: the wrong gas leaves a dirty bead, and the right gas lets the puddle flow clean. Tig welding gas types come down to argon first, helium and argon-helium mixes for special jobs, and carbon dioxide, which belongs to MIG, not TIG. This guide covers each gas and the regulators that meter it to the torch.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

BETOOLL Dual Output Argon Regulator

BETOOLL Dual Output Argon Regulator

BETOOLL9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A dual-output argon regulator with 2 flowmeters, 0-60 SCFH at 50 PSI, a 0-4500 PSI gauge and 2 hoses of 6.6 ft for two machines.

Pros

  • Dual flowmeters feed two machines with separate adjustments
  • 0-60 SCFH flow at 50 PSI with a ball flow indicator
  • 0-4500 PSI gauge monitors tank gas levels
  • Brass body, with 2 hoses of 6.6 ft included

Cons

  • No warranty term is stated
  • No certification is stated
  • Argon and argon blends only; helium is not listed
  • Dual output adds bulk at 6.8 x 8.0 x 4.9 inches
Muphop Argon Regulator Flow Meter Gauge

Muphop Argon Regulator Flow Meter Gauge

Muphop9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A brass argon regulator with a 0-60 CFH square flow tube, a 1 1/2 inch gauge reading 0-4000 PSI, a CGA-580 inlet and a 6.6 ft hose.

Pros

  • Works with argon, CO2 and helium on a CGA-580 inlet
  • Square flow tube reads 0-60 CFH
  • Large 1 1/2 inch gauge reads 0-4000 PSI
  • Brass build, 6.6 ft hose, clamp and mounting nut included

Cons

  • No warranty term is stated
  • No certification is stated
  • Single output feeds one machine only
  • No ball indicator is stated for the flow tube
YESWELDER Argon CO2 Regulator with 8.2 ft Hose

YESWELDER Argon CO2 Regulator with 8.2 ft Hose

YESWELDER9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An argon and CO2 regulator with a 0-4000 PSI inlet gauge, dual-scale outlet gauges for argon 0-30 CFH and CO2 0-20 CFH, and an 8.2 ft hose.

Pros

  • Dual-scale outlet gauge reads argon 0-30 CFH and CO2 0-20 CFH
  • Works with argon, helium and CO2
  • 8.2 ft hose included
  • Three outlet fittings: 9/16 inch male, 5/8 inch female and 1/4 inch hose barb

Cons

  • No warranty term is stated
  • No certification is stated
  • Argon flow tops out at 30 CFH, below the 0-60 CFH models here
  • Single output feeds one machine only
BOWELD Argon/CO2 Mig Tig Flow Meter Gas Regulator

BOWELD Argon/CO2 Mig Tig Flow Meter Gas Regulator

BOWELD9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single argon and CO2 flowmeter regulator with a 0-60 CFH square flow tube, a 1 1/2 inch gauge reading 0-3500 PSI, and a CGA-580 inlet.

Pros

  • Square flow tube reads 0-60 CFH with a ball indicator
  • Works with argon, helium and CO2
  • Fits female 9/16 inch by 18 nut or male 5/8 inch by 18 fitting
  • Hose clamp and mounting nut included

Cons

  • No warranty term is stated
  • No certification is stated
  • No hose included; the box holds the regulator, a clamp and a nut
  • Inlet gauge tops out at 3500 PSI, the lowest here

Tig welding gas types at a glance

Argon is the gas for TIG on steel, stainless and aluminum: it shields the puddle and the tungsten without adding anything to the weld. Helium runs hotter and suits thick aluminum, often mixed with argon. CO2 shields MIG welds on steel and does not belong on a TIG torch. The regulators below meter argon and CO2 through CGA-580 inlets, and the YESWELDER, BOWELD and Muphop also list helium.

Side by side

Regulator Gear Score Inlet gauge Flow range Hose
BETOOLL HW9003N-2 9.6/10 0-4500 PSI 0-60 SCFH 2 x 6.6 ft
Muphop YQ1 9.6/10 0-4000 PSI 0-60 CFH 6.6 ft
YESWELDER WX-03-CGA580 9.6/10 0-4000 PSI Argon 0-30 CFH, CO2 0-20 CFH 8.2 ft
BOWELD BO191 9.5/10 0-3500 PSI 0-60 CFH Not stated

Flow ranges are the maker’s stated gauge ranges, so set the regulator inside its stated range.

Argon: the default TIG gas

Argon suits TIG on steel, stainless and aluminum because it shields without reacting with the puddle. Every regulator here meters argon: the YESWELDER reads argon 0-30 CFH on its outlet gauge, and the BETOOLL, BOWELD and Muphop read 0-60 CFH or 0-60 SCFH. The regulators here are also listed for MIG work, so one regulator can serve either machine in a mixed shop.

Helium and argon-helium mixes

Helium adds heat to the arc, which helps on thick aluminum and copper where argon alone struggles to wet the joint. The YESWELDER, BOWELD and Muphop listings all state helium compatibility alongside argon and CO2, so those three regulators connect to a helium or argon-helium bottle when the job calls for it.

CO2: a MIG gas, not a TIG gas

CO2 shields MIG welds on steel, where it gives deep penetration. It does not shield TIG: the arc breaks CO2 down and the weld picks up oxygen, which leaves a dirty bead. The regulators here still list CO2 scales, the YESWELDER reads CO2 0-20 CFH, for the MIG machine in a mixed shop. If the bottle says CO2, it feeds the MIG gun, not the TIG torch.

The gear for TIG welding gas types

The regulators below meter the gases above to the torch: each one takes a CGA-580 cylinder, reads tank pressure on a gauge, and meters flow on a scale the welder can read.

Compressed gas. Chain gas cylinders upright, keep the regulator and hoses clear of the arc and hot metal, and check the manual before the first weld. Weld with ventilation and keep flammables clear of the arc.

FAQ for welders

Does CO2 work for TIG welding?

No. CO2 suits MIG on steel, not TIG. The YESWELDER reads CO2 0-20 CFH on its outlet gauge for MIG work, while its argon scale reads 0-30 CFH for TIG. Use argon on the TIG torch.

What gas suits TIG on aluminum?

Argon. It shields the puddle and the tungsten without adding anything to the weld. Helium or an argon-helium mix adds heat for thick aluminum, and the YESWELDER, BOWELD and Muphop regulators (on Amazon) all state helium compatibility.

What does a flowmeter regulator do?

It drops cylinder pressure to a working level and meters shielding gas to the torch at a set flow. The BETOOLL reads 0-60 SCFH at 50 PSI, and the BOWELD and Muphop read 0-60 CFH. Match the CGA-580 inlet to the cylinder valve.

Does helium need a different regulator?

No, if the regulator lists helium. The YESWELDER, BOWELD and Muphop listings all state argon, helium and CO2 compatibility on a CGA-580 inlet. The BETOOLL lists argon and argon blends on the same CGA-580 inlet.

Related: best TIG welder, best shielding gas for TIG welding, argon vs helium for TIG welding, argon gas regulator for TIG welding and the welding consumables hub.

More buying guides

Welding Consumables ·

TIG Welding Rod Types and Uses

ER70S-6 covers mild steel and ER308L covers stainless, and this guide sorts the families by metal, diameter and pack size so the rod matches…

Welding Consumables ·

Types of Gas Regulators for Welding

Single-stage, two-stage, flowmeter and preset regulators all drop cylinder pressure to working pressure, but they differ in steadiness, flow reading and fit, and the…