Propane Forge Temperature: What Heat to Expect
The makers list these forges as reaching welding temperature, with rated temperatures of 2600°F or 2700°F on the models covered here.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
MMasters 2 Burner Propane Forge Kit with Fire Bricks9.4/10View on Amazon - 2
Nelyrho 1 Burner Propane Blacksmith Forge Kit9.4/10View on Amazon - 3
VEVOR Portable Propane Forge9.7/10View on Amazon
A blade blank goes into the forge dull gray and needs to come out hot enough to move under the hammer. That change is the whole job of a propane forge, and propane forge temperature is the number that decides whether the steel gets there. This guide covers what heat to expect, what sets it, and how to read the figures makers put on their forges.
The forges covered here are rated at 2600°F or 2700°F, with one triple-burner model giving a 2500°F welding temperature. Those figures are the makers’ listed figures, not a promise for every heat, and the rest of this guide explains what sets the heat on the way from a cold start to full fire.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
What propane forge temperature to expect
The common rating in this guide is 2600°F. ATkrou and Nelyrho rate their four-burner and single-burner forges at 2600°F, and Simond Store rates its double-burner forge at 2600°F. Yoursme and E-cowlboy rate their two-burner forges at 2700°F, or 1482°C, and Yoursme gives a 2500°F welding temperature for its triple-burner model. The spread is narrow, and burner count alone does not set the ceiling: a single-burner Nelyrho forge carries the same 2600°F rating as the four-burner version from the same maker.
Rated temperatures side by side
| Forge | Burners | Rated temperature | Burner pressure | Body |
|---|---|---|---|---|
| ATkrou 4 Burner | 4 | 2600°F | Not stated | Stainless steel |
| Nelyrho 4 Burner | 4 | 2600°F | 0-30 PSI | Stainless steel |
| Nelyrho 1 Burner | 1 | 2600°F | 0-30 PSI | Stainless steel |
| Yoursme 2 Burner | 2 | 2700°F | 1-25 PSI | 16 gauge steel |
| E-cowlboy Dual Burner | 2 | 2700°F | 1-25 PSI | 16 gauge steel |
| Simond Store Double Burner | 2 | 2600°F | Not stated | Steel |
| Yoursme 3 Burner | 3 | 2700°F | 1-25 PSI | 16 gauge steel |
Read the rating with its condition. Simond Store’s blanket is rated to resist 2600°F, or 1425°C, which matches the forge rating, and Yoursme lists 2700°F as a welding temperature on its two-burner forge. Each row carries the rated figure for one model, with pressure and body material alongside it so the numbers stay in context.
What sets the temperature
Burner count spreads heat across the chamber, but in the models covered here it does not by itself raise the rated ceiling. The Yoursme forges space their burners 200mm apart, center to center. The ATkrou four-burner kit (on Amazon) measures 28.7 inches long, and the Simond Store double-burner forge measures 18.0 inches long with an inside chamber 4.4 inches high, 6.3 inches wide and 18 inches long. ATkrou says its four burners are distributed in equal proportions, so the heat is evenly distributed inside the forge, which is more suitable for heating long rods.
Gas pressure is the throttle. Nelyrho gives a burner nozzle pressure range of 0-30 PSI. Yoursme and E-cowlboy give an operating pressure range of 1-25 PSI, and the regulator gauge reads 0-0.6 Mpa, where 0.1 Mpa equals 1 Bar or 14.5 PSI. Open the gas inlet valves, then adjust the gas pressure to control the firepower. Simond Store notes you can check the pressure in the manometer while adjusting it.
Air supply also matters. The Yoursme, E-cowlboy and Simond Store burners carry an air choke valve on top that regulates the amount of air mixed with the propane during combustion. Yoursme and E-cowlboy state that a burner without an air choke cannot reach maximum temperature, because different pressures need different quantities of air. Set the choke for the pressure the forge is running at, not for the last job.
Doors and insulation hold the heat the burners make. Closing the two doors heats steel quicker, and ATkrou adds that one door stays open during extended high-temperature use to prevent overheating and maintain airflow. The Yoursme and Simond Store forges use a 1-inch thick ceramic fiber blanket, and Simond Store coats its blanket with rigidizer. ATkrou recommends applying refractory cement and covering with ceramic fiber, and Nelyrho recommends refractory materials or rigidizer on the fire-resistant insulation.
Running the forge at heat
Set up in order on the Yoursme kit. Assemble the forge, connect it to a standard propane tank with the POL CGA-510 connection and the 6.5-foot gas hose, and put the firebrick into the forge. Put a lit combustible into the forge, open all the gas inlet valves, and adjust the gas pressure to control the firepower. That kit includes 3 firebricks, 2 long and 1 short.
Simond Store notes its double-burner forge can run on 1 or 2 burners through the gas ball valve, and Yoursme notes its triple-burner forge allows the use of 1, 2 or 3 burners. After heating, disconnect the hoses or burners so residual heat in the hose cannot melt it. That shutdown step is one both ATkrou and Nelyrho warn about: a connected hose can take heat damage after use.
Run a propane forge outdoors or with strong ventilation, keep a CO alarm and a fire extinguisher close, and never leave a lit forge alone. That setup follows CPSC carbon monoxide guidance. A forge at full heat is an open flame in a steel box, and it deserves the same respect as any other shop fire.
FAQ for welders
How hot does a propane forge get?
The forges covered here are rated at 2600°F or 2700°F, with Yoursme giving a 2500°F welding temperature for its triple-burner model. Those are the makers’ listed figures. The heat at the work depends on pressure, air and the doors, while burner count affects how evenly the heat spreads across the chamber.
Is 2600°F hot enough to weld steel?
Simond Store says its 2600°F forge can reach welding temperature, and Yoursme lists 2700°F as a welding temperature on its two-burner forge. That is Simond Store’s claim for its own double-burner forge, not a rating that applies to every forge at 2600°F.
How many burners does a propane forge need?
The forges covered here run 1, 2, 3 or 4 burners, and a single-burner Nelyrho forge carries the same 2600°F rating as the four-burner version. More burners spread heat more evenly across the chamber, and Simond Store notes its double-burner forge can run on 1 or 2 burners through the gas ball valve.
What gas pressure does a propane forge run at?
Nelyrho gives a burner nozzle pressure range of 0-30 PSI. Yoursme and E-cowlboy give an operating pressure range of 1-25 PSI, with a regulator gauge that reads 0-0.6 Mpa. Adjust the gas pressure to control the firepower, and set the air choke to match the air to the pressure.
Do the forge doors stay open or shut?
Close both doors to heat steel quicker, but keep one door open during extended high-temperature use to prevent overheating and maintain airflow. That is the guidance ATkrou gives for its four-burner forge.
Related: best propane forge for blacksmithing, best 2 burner forge, electric vs propane forge, best forge refractory cement, and the metal fab tools hub. Also see propane forge for the home shop.




