Gas Cylinder Valve Types for Welding
Gas cylinder valve types come down to the fitting on the cylinder: CGA580 and CGA320 inlets for welding gases, a type-1 connection for propane, and a safety cap that guards an acetylene valve.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ARCCAPTAIN Argon/CO2/Helium Regulator9.6/10View on Amazon - 2
Acetylene Cylinder Safety Cap9.6/10View on Amazon - 3
Nitrogen Regulator 0-600PSI CGA580 Inlet9.6/10View on Amazon - 4
GasOne 2113+50105 4 ft Regulator and Propane Brass9.4/10View on Amazon
A cylinder valve is the fitting on top of a gas cylinder, and gas cylinder valve types are told apart by the connection on that fitting. The connection decides which regulator screws on, and matching the fitting to the gas keeps the setup safe to use. Match the fitting first, then the regulator to the gas and the work.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Pros
- Covers argon, CO2 and helium in one regulator
- Argon 0-60, CO2 0-65, helium 0-180 CFH
- Brass body, pressure relief valve, filter
- 1 Year warranty, 2 hose clamps, 1 hose barb
Cons
- No hose included, only 1 hose barb and 2 clamps
- Fits only CGA580 and CGA320
- No mixed-gas flow range is stated
- A single outlet serves a single cylinder

Acetylene Cylinder Safety Cap
The valve-protection step for an acetylene cylinder: a safety cap on a 3-1/8 x 11 fine thread.
Pros
- Protects the valve if the cylinder falls
- Fits a 3-1/8 inch collar, 3-1/8 x 11 thread
- Built to DOT, OSHA and MSHA requirements
- 1-year warranty with free replacement
Cons
- Fits only a 3-1/8 inch collar
- Needs a #3 Master Lock, a part to buy
- Covers the valve only, no regulator function
- The cap must come off before use

Nitrogen Regulator 0-600PSI CGA580 Inlet
The nitrogen step for pressure checks and purging, with a CGA580 inlet.
Pros
- CGA580 inlet fits nitrogen, argon, helium, inert gas tanks
- 0-4000 PSI cylinder gauge, 0-600 PSI output gauge
- Solid brass body, self-reseating relief valve
- 3000 PSI max input, 500 PSI max output
Cons
- No warranty term is stated
- No hose included, model sold without one
- Relief valve does not protect the downstream system
- 1/4-inch male flare outlet needs matching fittings

GasOne 2113+50105 4 ft Regulator and Propane Brass
The propane step for burners: a 4 ft steel braided hose and regulator.
Pros
- Steel braided hose, 4FT (48in) long
- Fits type-1 (QCC-1) tank connections
- Adjustable 0 to 20 PSI output for high-pressure burners
- 3/8-inch flare, 5/8 inch outside diameter
Cons
- No warranty term is stated
- Tools required for a secure leak free connection
- Propane only, not MIG or TIG shielding gas
- The 4 ft hose limits burner distance from the tank
Gas Cylinder Valve Types at a Glance
Shielding-gas cylinders use a CGA connection, a numbered fitting that pairs a gas family with a regulator inlet. CGA580 is the common inlet for argon, helium, nitrogen and other inert gases, and CGA320 is the inlet for carbon dioxide. Propane takes a type-1 (QCC-1) tank connection, while an acetylene cylinder valve is covered by a safety cap when the cylinder is moved or stored.
Side by Side
| Product | Connection | Stated range | Use | Warranty |
|---|---|---|---|---|
| ARCCAPTAIN Argon CO2 Helium Regulator | CGA580 and CGA320 inlet | 0-4000 PSI; argon 0-60, CO2 0-65, helium 0-180 CFH | MIG and TIG shielding gas | 1 Year |
| DiaoTu Acetylene Cylinder Safety Cap | 3-1/8 x 11 fine thread, fits 3-1/8 inch collar | Not stated | Guards the valve in transport and storage | 1-year warranty |
| NAKAO Nitrogen Regulator 0-600 PSI | CGA580 inlet, 1/4-inch male flare outlet | 0-4000 PSI cylinder gauge, 0-600 PSI output | HVAC purging, pressure checks, brazing, soldering | Not stated |
| GasOne 4 ft Propane Regulator and Hose | Type-1 (QCC-1) tank connection, 3/8 flare | Adjustable 0 to 20 PSI output | Propane burners, turkey fryers, smokers | Not stated |
Read the inlet marking on the cylinder valve before ordering: CGA580 and CGA320 inlets are not interchangeable, and the wrong one will not seal. Check the outlet thread too, since the regulators below use 9/16-inch, 5/8-inch and 1/4-inch threads and a 3/8-inch flare.
CGA580, CGA320 and the Other Fittings
- Argon, helium and nitrogen. CGA580 is the inlet for these gases. The NAKAO regulator (on Amazon) below pairs it with a 0-600 PSI output gauge for purging, pressure checks, brazing and soldering.
- Carbon dioxide. CGA320 is the inlet for CO2. The ARCCAPTAIN regulator (on Amazon) lists it beside CGA580, with argon at 0-60 CFH and helium at 0-180 CFH.
- Propane. A propane tank takes a type-1 (QCC-1) connection and a 3/8 flare M x 1/8 MNPT brass orifice, with a 4FT (48in) steel braided hose and an output of 0 to 20 PSI.
- Acetylene. An acetylene cylinder valve needs a safety cap when the cylinder is moved or stored. The DiaoTu cap fits a 3-1/8 inch collar on a 3-1/8 x 11 fine thread.
How to Match a Regulator to a Cylinder
Read the CGA marking stamped on the cylinder valve, then buy a regulator with the same inlet. Match the outlet thread to the hose and check the flow range against the work: the ARCCAPTAIN regulator lists argon at 0-60 CFH and helium at 0-180 CFH for MIG and TIG, while a nitrogen regulator with a 0-600 PSI output gauge suits pressure checks and purging. For propane, confirm a type-1 (QCC-1) tank connection and an output of 0 to 20 PSI. See the best gas regulator for MIG welding guide and the best propane gas regulator guide.
Gear for This Guide
These regulators and the safety cap below cover the connections in this guide: CGA580 and CGA320 inlets, a type-1 propane connection, and a cap that guards an acetylene valve.
Compressed gas safety. Keep cylinders upright and chained so they cannot fall, check every connection for leaks after opening the valve, and work with ventilation. The safety cap stays on an acetylene cylinder until the cylinder is chained in place.
For more options, see our welding consumables guides.
FAQ for welders
What does CGA580 fit?
CGA580 is the inlet for nitrogen, argon, helium and other inert gas tanks. The NAKAO regulator below uses a CGA580 inlet.
Can a single regulator cover argon, CO2 and helium?
Yes, when the listing states all three gases and both inlets. The ARCCAPTAIN regulator is built for argon, CO2 and helium, with a 0-4000 PSI inlet pressure range.
What fitting does a propane tank use?
A propane tank uses a type-1 (QCC-1) connection. The GasOne kit fits type-1 tank connections with a 3/8 flare M x 1/8 MNPT brass orifice and a 4FT (48in) steel braided hose.
How do I protect a cylinder valve when moving a cylinder?
Fit a safety cap over the valve before the cylinder is moved or stored. The DiaoTu cap fits a 3-1/8 inch collar on a 3-1/8 x 11 fine thread.
Related: small vs large welding gas cylinder, single stage vs dual stage gas regulator, best gas regulator for MIG welding, and best propane gas regulator.




