G10 vs Micarta Knife Scales: Which One Should You Buy?
G10 and micarta both make strong knife handles, but they differ on grip, water, shaping and color, and the scales in this guide are all G10.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
IECAP LLC Bookmatched Desert Ironwood Knife Handle Scales9.7/10View on Amazon - 2
O1 Precision Ground Tool Steel Flat Bar 1/8" x 1-1/2" x 12"9.6/10View on Amazon - 3
O1 Tool Steel Precision Ground Flat Stock 3/16" x 2" x 12"9.6/10View on Amazon - 4
Tinlade 10 Pcs G10 Knife Handle Liners for ScalesView on Amazon - 5
G10 Scales Natural JADE GREEN 1/4" X 1.5" X 5.5" Knife HandleView on Amazon - 6
Malayan Products 2 Ram Horn Scales Knife Handle MakingView on Amazon - 7
IECAP LLC 4 Pieces Desert Ironwood Knife ScalesView on Amazon - 8
IECAP LLC Desert Ironwood Knife Handle ScalesView on Amazon
A knife handle starts as a flat slab, and the choice is usually between G10 and micarta. G10 vs micarta knife scales comes down to this: G10 is glass fiber in epoxy resin, steady and hard to deform, while micarta is layers of cloth or paper in resin, warmer in the hand and grippy when wet. The scales below are all G10, and no micarta scale is among them, so the micarta side here is the material in general terms while the G10 side uses the stated figures from the scales below.
Other welders and gear to compare
Tinlade 10 Pcs G10 Knife Handle Liners for ScalesCheck price on Amazon
G10 Scales Natural JADE GREEN 1/4" X 1.5" X 5.5" Knife HandleCheck price on Amazon
Malayan Products 2 Ram Horn Scales Knife Handle MakingCheck price on Amazon
IECAP LLC 4 Pieces Desert Ironwood Knife ScalesCheck price on Amazon
IECAP LLC Desert Ironwood Knife Handle ScalesCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
G10 vs micarta knife scales: the short answer
Pick G10 for a handle that must stay flat and steady through shop use and wet hands. Pick micarta for a handle that should feel warm and hold grip when wet. The sections below put them side by side, then show what the G10 scales in this guide actually state.
The difference in one paragraph
G10 is glass fiber cloth set in epoxy resin, pressed into a hard slab that stays flat and holds its shape. Micarta is layers of cloth or paper set in resin, pressed the same way, and it feels warmer in the hand and grips well when wet. Both shape with hand tools, and both serve as the handle slabs on a knife tang. The choice is about feel, water and color, not strength alone.
Side by side
| G10 | Micarta | Notes | |
|---|---|---|---|
| Base material | Glass fiber cloth in epoxy resin | Layers of cloth or paper in resin | G10 makeup is stated |
| Grip | Firm, textured surface on the slabs | Warm feel, grip holds when wet | Grip notes are general |
| Water | Stated as stable and hard to deform | Can take in oil and moisture over time | No micarta scale below |
| Shaping | Drill, saw, sand, grind or polish | Sands and shapes with hand tools | Both shape with hand tools |
| Colors | Black, white, red, blue, orange, yellow, brown and green | Browns, blacks and natural tones are the classic colors | 8 colors in the liner set |
| Form | Liners and scale blanks | Scale blanks | Every scale here is G10 |
The G10 column uses the stated figures from the scales below. The micarta column describes the material in general terms, since no micarta scale is among them.
When G10 is the better choice
- A handle that must stay flat. G10 is stated as stable in structure and hard to deform, so it suits a working knife that lives in the shop.
- Wet hands. The liners are stated as water resistant, and one slab is stated as impermeable.
- Color lines and bright handles. The liner sets come in 8 colors and 5 colors, so a liner can add a color line between scale and tang.
- A first set of scales to shape. G10 drills, saws, sands, grinds and polishes, and the SICOLAS slabs state they can be drilled, sanded and shaped to fit.
The best belt grinder for knife making guide covers the grinder that shapes these slabs.
When micarta is the better choice
- A warm feel in the hand. Micarta feels warmer than G10 and stays pleasant through a long job.
- Grip when wet. Micarta holds grip with wet hands, which suits a working knife used outdoors.
- A classic look. Micarta darkens with oil and use, and the change suits a knife that earns wear.
- Hand shaping. Micarta sands and shapes with hand tools, like G10, and it takes a matte or polished finish.
How to tell what you are buying
Scale listings name the material first, then the form. Read both before ordering:
- Material. G10 means glass fiber in epoxy resin. Micarta means cloth or paper layers in resin. If the name says neither, it is not one of these materials.
- Liner or slab. A liner is a thin sheet, 0.04 inch here, that sits between scale and tang as a color line. A slab is the handle itself, 0.31 inch or 0.28 inch here, shaped to fit the tang.
- Size against the tang. The liners here measure 6.3 x 1.97 inches or 6.3 x 2 inches, and the slabs 4.72 x 1.57 inches. Check the size against the tang before ordering.
- Pack count. The sets here hold 30 pieces, 10 pieces or 2 pieces. A liner set covers spares and color swaps; a slab pair covers one handle.
The G10 scales in this guide
Kathfly makes the liner set: 30 pieces in 8 colors, each sheet 6.3 x 1.97 x 0.04 inches, in glass fiber cloth and epoxy resin. The sheets drill, saw, grind or polish, and the set suits liners and color swaps.
SICOLAS makes the gray and black slabs: 2 pieces, each 120x40x8mm, or 4.72 x 1.57 x 0.31 inches, with a textured grip and a firm, non-slip surface. The slabs come in the raw state, not pre-shaped, and they drill, sand and shape to fit.
Tinlade makes the liner set in 5 colors: 10 pieces, each 6.3 x 2 x 0.04 inch, in epoxy resin and glass fiber. The maker gives 0.04 inch and 0.39 inch for the thickness of these sheets; check before ordering.
Cool Hand makes the green and black scales: 2 pieces, each 4.72 x 1.57 x 0.28 inches and 5.64 oz, with high hardness and abrasive resistance. The scales polish well and can be processed by hand, with a cutting tool or CNC.
| Scale | Size | Pack | Colors |
|---|---|---|---|
| Kathfly G10 spacer sheets | 6.3 x 1.97 x 0.04 in | 30 pieces | 8 colors |
| SICOLAS G10 slabs | 4.72 x 1.57 x 0.31 in | 2 pieces | Gray and Black |
| Tinlade G10 liners | 6.3 x 2 x 0.04 in | 10 pieces | 5 colors |
| Cool Hand G10 scales | 4.72 x 1.57 x 0.28 in | 2 pieces | Green and Black |
Grinding G10 dust. Grinding, sanding or sawing G10 makes fine glass fiber dust. Wear eye protection and a respirator, work with ventilation or outdoors, and keep dust off the bench and out of the shop air.
FAQ for welders
Is G10 better than micarta for a knife handle?
Neither wins on every job. G10 stays flat and steady and suits a working knife that gets wet, while micarta feels warmer and holds grip when wet. Pick by feel and use, not by name alone.
Can I shape G10 scales with hand tools?
Yes. The slabs here state they can be drilled, sanded and shaped to fit, and the liners drill, saw, grind or polish. Wear eye protection and a respirator when grinding, and work with ventilation.
What size G10 scale do I need?
Match the slab to the tang. The slabs here measure 4.72 x 1.57 inches and the liners 6.3 x 1.97 inches or 6.3 x 2 inches, so check the size against the tang before ordering.
Do G10 liners change the handle thickness?
A liner measures 0.04 inch, so it reads as a thin color line between scale and tang rather than a thick layer. Check the stated thickness before ordering.
Does micarta need a finish?
Micarta shapes and sands like G10 and can be left matte or polished. Oil and use darken it over time.
Related: best forge burner kit for knife making, carbon vs stainless knife steel, best belt grinder for knife making, and the knife making hub.




