Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Chipping Hammer Uses for Slag Removal

A chipping hammer chips slag off stick and flux core welds and clears spatter from the bead. What it does, when to reach for the wire brush, and which of the two hammers here fits the work.

Chipping Hammer Uses for Slag Removal
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ESTWING Welding/Chipping HammerESTWING Welding/Chipping Hammer9.6/10View on Amazon
  2. 2VASTOOLS Welding Chipping Hammer with Coil SpringVASTOOLS Welding Chipping Hammer with Coil Spring9.5/10View on Amazon

The bead is laid and the slag crust has cooled into a hard shell over the weld. The tool that knocks that crust off is a chipping hammer, and chipping hammer uses run past slag removal: the same hammer clears spatter, cleans the bead before the next pass, and, with a wire brush, takes rust and paint off the metal before you strike an arc. This guide covers what the hammer does, when to reach for the brush instead, and which of the two hammers here fits the work.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

ESTWING Welding/Chipping Hammer

ESTWING Welding/Chipping Hammer

Estwing9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13 oz forged hammer with a 7/8 in chisel, replaceable pointed tips, and a shock reduction grip that cuts impact vibration by 70%.

Pros

  • Forged in one piece from solid American steel
  • Replaceable pointed tips for precision clean-up
  • Shock reduction grip cuts impact vibration by 70%
  • 7/8 in chisel side for chipping slag and spatter

Cons

  • No wire brush included in the box
  • 13 oz is light for thick, heavy slag
  • No spare tips in the box
  • 7/8 in chisel is narrower than the VASTOOLS chisel
VASTOOLS Welding Chipping Hammer with Coil Spring

VASTOOLS Welding Chipping Hammer with Coil Spring

VASTOOLS9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A three piece set with a high carbon steel chipping hammer, a 1-1/16 in chisel, a coil spring handle, and an 11 in wire brush.

Pros

  • 1-1/16 in chisel clears slag faster than a narrower edge
  • Three pieces: hammer and 11 in wire brush in one set
  • Coil spring handle absorbs the shock of contact
  • Brush has 4x15 rows for coverage on rust, paint and scale

Cons

  • No stated warranty term
  • Chisel and point are fixed, not replaceable
  • No vibration reduction figure stated
  • 1-1/16 in chisel is wide for tight corners

Chipping hammer uses in one paragraph

A chipping hammer has one main job and several smaller ones. The main job is chipping the slag crust off a stick or flux core weld once the bead has cooled enough to work. The crust lifts in chips under light taps from the chisel end, and the pointed end picks slag out of corners and along the edge of the bead. The same hammer knocks weld spatter off the metal around the bead, and it cleans the joint before the next pass so the new bead lays on clean metal. With a wire brush in the other hand, the hammer’s partner tool, you sweep the loosened slag away and take rust, paint and scale off the joint before welding. A gas MIG bead leaves no slag, so the hammer earns its keep on stick and flux core, though it still knocks spatter off a MIG bead.

Chipping hammers for slag removal

The two hammers here both chip slag, and the choice is between a single forged hammer with replaceable tips and a three piece set that adds a wire brush.

Side by side

VASTOOLS 3-piece set Estwing E3-WCT What changes
Chisel width 1-1/16 in 7/8 in Wider chisel clears faster
Listed dimensions 10.5 x 6.1 x 1.6 in 11.1 x 7.1 x 1.3 in Similar hand tool size
Handle Coil spring handle Molded vinyl shock reduction grip Estwing states a 70% cut
In the box Hammer and wire brush, 3 pieces Hammer only, 1 piece Set adds the brush
Replaceable tips Not stated Yes, replaceable pointed tips Estwing tips swap out
Vibration Spring handle absorbs shock Grip cuts vibration by 70% Both soften the shock

A wider chisel covers more crust per tap, so it clears a wide flat bead faster, and the brush decides how clean the bead looks after. The Estwing trades the brush for replaceable tips and a grip that cuts vibration, while the VASTOOLS set trades replaceable tips for the brush and the wider chisel. Pick by the work: tight corners and detail want the replaceable point, wide flat beads want the wide chisel and the brush.

How to use a chipping hammer

  • Let the bead cool. Hot slag burns on contact, so wait until the bead has lost its glow.
  • Wear safety glasses under the helmet. Chipping throws small sharp chips off the bead, and glasses keep them out of the eyes while the helmet is up.
  • Tap, do not swing. Light taps with the chisel end lift the crust; hard swings dent the bead and bounce the hammer.
  • Work from the edge in. Start at the edge of the crust and work toward the middle, then pick the corners with the point.
  • Brush after chipping. Sweep the loosened slag off with the wire brush and check the bead before the next pass or a coat of paint.

When the wire brush does the work

The brush is not a second hammer. It sweeps loosened slag off the bead, cleans light rust and paint from the joint, and leaves the metal ready for the next pass or a coat of paint. The VASTOOLS brush has 4×15 rows of bristles about 1 in long. Use the brush after the hammer, not instead of it: bristles bend on a hard crust and will not lift it.

FAQ for welders

What is a chipping hammer used for?

Chipping the slag crust off stick and flux core welds, knocking spatter off the metal, and cleaning the bead before the next pass or paint. With a wire brush it also cleans rust, paint and scale from the joint.

Do I need a chipping hammer for MIG welding?

For gas MIG, no slag to chip: a gas shielded bead leaves none, though the hammer still knocks spatter off a MIG bead. For flux core, yes: flux core leaves a slag crust like stick welding, and the hammer chips it off. See our best flux core welder guide for machines that run it.

Can a chipping hammer clean rust and paint?

The hammer itself chips hard crust; the wire brush does the rust and paint work. The VASTOOLS set pairs the hammer with an 11 in brush made for paint stains, rust, slag, solder and scale, per the listing.

Do chipping hammer tips wear out?

Yes. The chisel edge dulls and the point blunts with use. The Estwing E3-WCT (on Amazon) has replaceable pointed tips, so you swap the tip instead of the hammer, while the VASTOOLS chisel and point are fixed.

Should I wear safety glasses when chipping slag?

Yes, under the helmet. Chipping throws small sharp chips off the bead, and glasses keep them out of the eyes while the helmet is up.

Related: best stainless steel chipping hammer, air hammer vs chipping hammer, ball peen hammer uses, and the metal fab tools hub.

More buying guides