Air Hammer Uses: Pneumatic Tools for Metalwork
Air hammer uses range from cutting and shaping sheet metal to riveting, rust removal and breaking concrete, and the right chisel decides how clean each job goes.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Air Hammer, Chisels Round Shank9.7/10View on Amazon - 2
FICHFOYE Pneumatic Air Hammer Kit9.6/10View on Amazon - 3
Smoothing Air Hammer Bits Set9.6/10View on Amazon - 4
AMGSH 10 Pcs Air Hammer Pneumatic Chisels Tools9.5/10View on Amazon
A dented fender, a rusted seam, a rivet that will not move and a patch panel that needs shaping all sit on the same bench, and each one asks for a different kind of force. Air hammer uses cover that whole spread: a pneumatic hammer drives a chisel with rapid blows to cut, shape, rivet, strip and break metal and masonry in the shop. This guide walks through each job, the chisel that fits it, and the gear that does the work.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

VEVOR Air Hammer, Chisels Round Shank
A 4500 BPM pneumatic hammer with a 19-needle scaler, 4 chisels and a 1.57 inch stroke for cutting, rust removal and demolition.
Pros
- 4500 BPM with a 1.57 inch stroke, the highest blow rate in this guide
- 19-needle scaler included for rust removal
- 4 round shank chisels, 4.7 inches long, plus 3 air nozzle connectors and a spring
- Powder-coated aluminum alloy housing with an air spring system for vibration reduction
Cons
- Air consumption of 11.5 CFM at 90 PSI needs a compressor that can keep up
- No warranty term is stated in the listing
- No case is listed in the box
- Impact energy in joules is not stated

FICHFOYE Pneumatic Air Hammer Kit
A 2500 BPM long-stroke kit with 5 chisels, a quick-change retainer and a carrying case for automotive and metal work.
Pros
- 2500 BPM with a 3-5/8 inch stroke and up to 46 J impact energy
- 5 alloy-steel chisels and a plastic carrying case in the box
- Self-locking quick-change retainer for tool-free chisel changes
- Rubber-coated grip for control and reduced vibration
Cons
- No air consumption or pressure figure is stated
- No warranty term is stated in the listing
- No weight is stated in the listing
- Chisel lengths are not stated in the listing

Smoothing Air Hammer Bits Set
A 5-piece set of alloy-steel smoothing bits in 4 shapes with a spring, for forming sheet metal, rivets and surface finishing.
Pros
- 4 bit shapes plus a spring cover forming, riveting, stripping and smoothing
- Heat-treated alloy steel with a polished, easy to clean surface
- Flat and oval heads made for forming sheet metal
- Light at 1.0 lb for the full set
Cons
- Bits only: no air hammer is included
- No warranty term is stated in the listing
- No shank size is stated in the listing
- The listing gives no hardness figure for the steel

AMGSH 10 Pcs Air Hammer Pneumatic Chisels Tools
A 10-piece set of 9 high-carbon steel chisels in different shapes with a spring, for demolition, chiseling and rust removal.
Pros
- 9 different shapes cover demolition, chiseling, rust removal and cutting hardware
- Heat-treated high carbon steel for strength and durability
- 0.401 inch shank fits 150 and 250 air hammer models
- Spring included to hold the chisel in the hammer
Cons
- Chisels only: no air hammer is included
- No warranty term is stated in the listing
- No weight is stated in the listing
Air hammer uses in metalwork
An air hammer is a pneumatic chisel driver: compressed air moves a piston that strikes the chisel again and again, in short, repeated blows. The listings behind this guide name cutting, scraping, shaping, riveting, stripping, rust removal and demolition as the core jobs.
Cutting is the job every listing in this guide names. An air hammer with a cutting chisel slices sheet metal and trims edges: the VEVOR listing names cutting metal, the FICHFOYE kit (on Amazon) lists cutting alongside scraping, shaping and demolition, and the ZMCYNG bits (on Amazon) and the AMGSH set list cutting too. A flat chisel suits straight cuts and a narrow one follows a curve.
Shaping and forming sheet metal is another core use. The flat and oval head surfaces of the ZMCYNG smoothing bits are made for forming sheet metal, and the FICHFOYE kit lists shaping among its jobs. A smoothing bit spreads each blow across a wider face, which suits planishing a dent or easing a curve.
Riveting uses the same hammering action with a different bit: the hammer sets rivets and works seams instead of cutting them apart. The ZMCYNG listing names riveting and wind pipe seam work, and the AMGSH set is made to fit pneumatic rivet hammers. A rivet set or a flat-faced bit seats the rivet head.
Rust and scale removal is where the needle scaler earns its place. The VEVOR kit includes a 19-needle air scaler for rust removal, and the AMGSH set lists removing rust and welding spots among its uses. Needles strike the surface at many points and lift scale and rust off flat steel. See the air hammer vs needle scaler guide for how the two tools differ.
Demolition rounds out the list: breaking concrete walls and flooring, demolishing masonry, crushing hard rock and chiseling. The VEVOR listing names breaking concrete walls and flooring, the FICHFOYE kit lists demolition, and the AMGSH set lists demolishing masonry and concrete and crushing solid rock.
Side by side
| Pick | Blows per minute | Stroke | Chisels in the box |
|---|---|---|---|
| VEVOR 4500 BPM Air Hammer | 4500 BPM | 1.57 in | 4 |
| FICHFOYE Pneumatic Air Hammer Kit | 2500 BPM | 3-5/8 in | 5 |
| ZMCYNG Smoothing Air Hammer Bits | Not stated | Not stated | 4 bits plus a spring |
| AMGSH Air Hammer Chisels | Not stated | Not stated | 9 chisels plus a spring |
The table above lines up the 4 picks on the figures the listings state. The VEVOR hammer (on Amazon) states the highest blow rate at 4500 BPM, while the FICHFOYE kit states the longest stroke at 3-5/8 inches and up to 46 J of impact energy. The chisel sets state no blow rate or stroke because they are bits, not hammers.
When an air hammer is the better choice
- Many repeated blows. Cutting, shaping, riveting and chipping all need the same hit landed again and again.
- Tight spots. A compact air hammer reaches seams, brackets and panels where a full swing will not fit.
- Rust and scale. A needle scaler clears a surface with many small strikes.
- Breaking masonry and concrete. Repeated blows split brittle material without the weight of a larger demolition tool.
When to reach for a different tool
- No air supply. An air hammer needs a regulated air supply, and the FICHFOYE listing says to connect only to a compatible regulated supply.
- Delicate panels. Light sheet can tear or stretch under repeated blows, so a hand tool gives more control.
- Small one-off jobs. A lone rivet or a small patch may be simpler with hand tools than with setting up the air line.
How to pick the right chisel
Match the chisel to the job. A flat or oval smoothing bit suits forming sheet metal and finishing a surface, which is the job the ZMCYNG set is made for. A pointed chisel suits breaking and chipping, and a wide flat chisel suits cutting and scraping. The AMGSH set covers that spread with 9 different shapes, and the FICHFOYE kit includes 5 chisels for cutting, scraping, splitting, shaping and leveling. Check the shank before buying bits: the AMGSH chisels (on Amazon) have a 0.401 inch shank and fit 150 and 250 air hammer models.
Chisel length matters where reach is tight. The VEVOR chisels are 4.7 inches long, or 120 mm, and the FICHFOYE kit uses a quick-change retainer that holds compatible chisels and allows fast, tool-free changes between jobs.
The gear for these jobs
The picks below cover the jobs above: a full kit, a hammer with a needle scaler for rust work, and chisel sets for hammers already in the shop.
FAQ for welders
What is an air hammer used for in metalwork?
An air hammer drives a chisel with rapid pneumatic blows to cut, shape, rivet, strip and break metal and masonry. The listings in this guide name cutting and shaping sheet metal, riveting, rust removal and breaking concrete as the main jobs.
Can an air hammer cut sheet metal?
Yes. Cutting metal is named in the listings for the VEVOR hammer, the FICHFOYE kit and the chisel sets. A cutting chisel trims sheet and follows edges, and the ZMCYNG smoothing bits are made for metal cutting and surface finishing.
Can an air hammer remove rust?
Yes, with the right attachment. The VEVOR kit includes a 19-needle air scaler made for rust removal, and the AMGSH set lists removing rust and welding spots among its uses.
What air supply does an air hammer need?
A regulated air supply from a compressor. The FICHFOYE listing says to connect only to a compatible regulated air supply, and the VEVOR listing states an average air consumption of 11.5 CFM at 90 PSI through a 1/4 NPT inlet.
Can an air hammer break concrete?
Yes, for light demolition. The VEVOR listing names breaking concrete walls and flooring, the FICHFOYE kit lists demolition, and the AMGSH set lists demolishing masonry and concrete and crushing solid rock.
Related: best pneumatic air hammer, best pneumatic air hammer under 150, air hammer vs needle scaler, and dead blow hammer uses. Also see the metal fab tools hub.




