Digital Caliper vs Micrometer: Which One Should You Buy?
The Starrett and HFS calipers cover a 0-6 inch range, while the REXBETI and Mitutoyo micrometers state finer accuracy, plus or minus 0.0001 inch.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
REXBETI Outside Micrometer9.5/10View on Amazon - 2
Starrett Stainless Steel Electronic Slide Caliper9.5/10View on Amazon - 3
Mitutoyo 103-177, 0-1 X .001 Outside Micrometer9.4/10View on Amazon - 4
HFS Imperial 0-6 Inch Dial Caliper9.4/10View on Amazon
Verdict. The micrometer examples state finer accuracy, while the caliper examples cover a wider range. Pick the micrometer side for fine outside diameters, and pick the caliper side for general measuring across a shop day.
A shaft needs checking against a drawing, a hole needs a true diameter, and the tool in your hand decides whether the reading means anything. This digital caliper vs micrometer comparison puts caliper examples against micrometer examples, using what each maker states about range, resolution, accuracy and build, so you can pick the side that fits the work.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The four tools

REXBETI Outside Micrometer
A 0-25 mm digital outside micrometer with 0.00005 inch resolution, carbide-tipped faces, a ratchet stop, a hard case and a spare battery.
Pros
- 0.00005 inch / 0.001 mm resolution with plus or minus 0.0001 inch stated accuracy
- Carbide-tipped measuring faces resist wear from repeated contact
- Ratchet stop applies uniform measuring force for repeatable readings
- Hard protective case and a spare battery in the box
Cons
- Range tops out at 25 mm, far shorter than the 0-6 inch calipers
- No weight stated in the listing
- No warranty term stated
- Digital display needs a battery; only one spare is included

Starrett Stainless Steel Electronic Slide Caliper
A 0-6 inch stainless steel electronic caliper with a large LCD, .0005 inch resolution, in/mm conversion and a fine adjustment thumb wheel.
Pros
- .0005 inch / 0.01 mm resolution on a large, high-contrast LCD
- 0-6 inch range with inch/millimeter conversion
- Hardened stainless steel measuring surfaces for durability and corrosion resistance
- Auto-off after 30 minutes, with no loss of position on wake
Cons
- No accuracy figure stated, only resolution
- No case stated in the listing
- No warranty term stated
- 0.7 lb, the highest stated weight here

Mitutoyo 103-177, 0-1 X .001 Outside Micrometer
A 0-1 inch outside micrometer with carbide-tipped faces, a ratchet stop, plus or minus 0.0001 inch stated accuracy and a fitted plastic case.
Pros
- Plus or minus 0.0001 inch stated accuracy
- Carbide-tipped measuring faces
- Ratchet stop mechanism
- 0.55 lb, the lowest stated weight here, with a fitted plastic case
Cons
- 0-1 inch range, the narrowest range here
- 0.001 inch graduations, coarser than the digital micrometer reading
- Box names only the micrometer and its fitted case
- No metric mode stated

HFS Imperial 0-6 Inch Dial Caliper
A 0-6 inch mechanical dial caliper with plus or minus 0.001 inch accuracy, four-way measuring and a fitted protective case.
Pros
- Four-way measuring: outside, inside, depth and step
- Plus or minus 0.001 inch accuracy with 0.001 inch graduations
- Shock-resistant dial for shop use
- Fitted protective case included
Cons
- Mechanical dial, no digital readout or metric conversion stated
- 0.001 inch graduations read coarser than the Starrett .0005 inch resolution
- Hardened carbon steel with no stated corrosion resistance
- 0.66 lb, heavier than the Mitutoyo at 0.55 lb
Digital caliper vs micrometer side by side
| REXBETI Digital Micrometer | Starrett EC799A-6/150 | Mitutoyo 103-177 | HFS Imperial Dial Caliper | |
|---|---|---|---|---|
| Gear Score | 60 | 59 | 56 | 55 |
| Range | 0-25 mm | 0-6 in | 0-1 in | 0-6 in |
| Resolution | 0.00005 in / 0.001 mm | .0005 in / 0.01 mm | .001 in graduations | 0.001 in graduations |
| Stated accuracy | ±0.0001 in | Not stated | +/-0.0001 in | ±0.001 in |
| Measuring faces | Carbide tipped | Hardened stainless steel | Carbide tipped | Hardened carbon steel |
| Display | Large LCD, inch/metric | Large LCD, in/mm | Satin chrome graduations | Mechanical dial |
| Ratchet stop | Yes | Not stated | Yes | Not stated |
| In the box | Hard case, extra battery | Not stated | Fitted plastic case | Fitted protective case |
| Weight | Not stated | 0.7 lb | 0.55 lb | 0.66 lb |
| Warranty | Not stated | Not stated | Not stated | Not stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 22 November 2026. No maker here states a warranty term or a safety certification, and the REXBETI gives no weight.
Resolution and accuracy
Resolution is the smallest change a tool shows, and accuracy is how close the reading sits to true. The REXBETI digital micrometer lists 0.00005 inch resolution with plus or minus 0.0001 inch accuracy: the finest resolution in this comparison, with accuracy tied with the Mitutoyo. The Mitutoyo micrometer states plus or minus 0.0001 inch accuracy with 0.001 inch graduations. The Starrett caliper lists .0005 inch resolution and names no accuracy figure, while the HFS dial caliper states plus or minus 0.001 inch accuracy with 0.001 inch graduations. Read resolution and accuracy as separate figures: a fine display step does not by itself prove a fine accuracy claim.
Range
Range is where the two sides split hardest. Both caliper examples cover 0-6 inch. The REXBETI micrometer covers 0-25 mm, and the Mitutoyo covers 0-1 inch. The micrometer examples cover a narrow band of sizes. Both state plus or minus 0.0001 inch accuracy, finer than the HFS figure of plus or minus 0.001 inch, while the Starrett states no accuracy figure. The Mitutoyo graduations at 0.001 inch still read coarser than the Starrett display step of .0005 inch, so range alone does not make a reading finer.
What each tool measures
The HFS dial caliper is the only example here that measures four ways: outside, inside, depth and step, with a thumb roller for fine adjustment and a locking screw to hold the reading. The Starrett electronic caliper is a slide caliper with a fine adjustment thumb wheel, and it converts between inch and millimeter readings. The micrometers measure outside diameters: the REXBETI states outside-diameter measurement, and the Mitutoyo is an outside micrometer. For inside, depth or step work, the caliper side is the only side with an example that states it.
Build, faces and cases
The Starrett lists hardened stainless steel measuring surfaces, and the HFS lists precision-finished hardened carbon steel. The micrometer faces are carbide tipped on both the REXBETI and the Mitutoyo, and both micrometers have a ratchet stop; the REXBETI maker says its ratchet stop applies uniform measuring force. Cases come with three of the four: the HFS lists a fitted protective case, the REXBETI a hard protective case, and the Mitutoyo a fitted plastic case. The Starrett names no case. On weight, the Mitutoyo lists 0.55 lb, the HFS 0.66 lb and the Starrett 0.7 lb; the REXBETI gives no weight, so it cannot be ranked on heft.
Choose the digital caliper if
- You measure sizes up to 6 inches, beyond the reach of either micrometer here.
- You measure inside, depth or step features as well as outside ones, which the HFS dial caliper states.
- You want a large LCD with inch and millimeter conversion, which the Starrett caliper offers.
- You prefer a mechanical dial readout over a digital display, which the HFS dial caliper offers.
Choose the micrometer if
- Your work is outside diameters in a narrow size band.
- You want the finest stated accuracy here, plus or minus 0.0001 inch.
- You want carbide-tipped faces and a ratchet stop for repeatable pressure.
- You want a fitted case in the box.
Before You Strike an Arc
- Zero the Starrett with its zero button before the first measurement of the day, and re-check zero after the tool has been moved.
- Wipe the carbide faces of the micrometers clean before measuring, so grit does not sit between the faces and the work.
- Keep the HFS, REXBETI and Mitutoyo in their fitted cases between jobs; the Starrett names no case.
- Keep the REXBETI spare battery with the tool, so a flat battery does not stop a measuring session.
FAQ for welders
Which is more accurate, a digital caliper or a micrometer?
Between these four, the micrometer side states the finer accuracy: both the REXBETI and the Mitutoyo state plus or minus 0.0001 inch. The HFS dial caliper states plus or minus 0.001 inch, and the Starrett states resolution of .0005 inch without naming an accuracy figure. Accuracy and resolution are separate figures, so compare the stated accuracy numbers, not the display steps.
Can a digital caliper replace a micrometer?
For general measuring across a 0-6 inch range, yes, and the HFS also measures inside, depth and step. For fine outside diameters, the micrometer examples state plus or minus 0.0001 inch accuracy, finer than the HFS figure of plus or minus 0.001 inch. Keep the micrometer for the finest outside work, and the caliper for everything else.
What does 0.00005 inch resolution mean on the REXBETI?
It is the smallest change the display shows, stated as 0.00005 inch or 0.001 mm. Resolution is not accuracy: the same maker states accuracy of plus or minus 0.0001 inch. A fine display step helps you read small changes, but the accuracy figure is what bounds the error.
Which of these tools come with a case?
The HFS lists a fitted protective case, the REXBETI a hard protective case, and the Mitutoyo a fitted plastic case. The Starrett names no case. The REXBETI also includes a spare battery.
Which micrometer here reads in metric?
The REXBETI switches between inch and metric readings with a single button, and its display shows both. The Mitutoyo is a 0-1 inch micrometer with no metric mode stated. The Starrett caliper converts between inch and millimeter readings.
Related: micrometer vs caliper, how to use digital calipers, best manual caliper, and the best micrometer set with case.
Scoring, line by line
Each tool is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| REXBETI Digital Micrometer | 9.5 | 32 | 21 | 20 | 0 | 0 |
| Starrett EC799A-6/150 | 9.5 | 30 | 21 | 20 | 0 | 0 |
| Mitutoyo 103-177 | 9.4 | 28 | 21 | 19 | 0 | 0 |
| HFS Imperial Dial Caliper | 9.4 | 27 | 20 | 20 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.




